Serta Executive User manual

Executive Chair
PRODUCT GUIDE & ASSEMBLY INSTRUCTIONS
So comfortable,
you’ll feel the difference
the moment you sit down.

Should you prefer to speak with a
customer service representative,
you may call toll free:
1-855-372-2315
22

Guidelines
FAILURE TO FOLLOW THESE WARNINGS
WHEN IN USE COULD RESULT IN INJURY
• Do not stand on the item or use as a step ladder
• Do not use this item unless all bolts and screws are
firmly secured and fastened.
• Check all bolts and screws every 90 days. As
necessary tighten if any are loose.
• Lift up then move. Pushing over or dragging this
product can result in an injury or cause damage to
the floor and piece.
33

Pre-Assembly Preparation:
Please read through this instruction booklet before
beginning assembly of this item.
Two adults are recommended for assembly.
• Clear out the space for assembly and lay out all
parts on Parts List, extra room will allow you to
easily determine if all the pieces are present.
• Save all packing materials until assembly is
complete to avoid accidentally discarding smaller
parts or hardware.
• Keep small parts and pieces away from children
and pets until fully assembled.
• Please check for any loose screws and tighten them
before you use.
WARNING:
DO NOT LET CHILDREN PLAY IN OR AROUND
THE UNIT DUE TO THE POSSIBLE RISK OF INJURY.
4

Parts List
5
Casters (5) Star Base (1)
Gas Lift with
Telescoping Cover (1) Seat Plate (1)
Left Arm (1) Right Arm (1)
Seat Cushion (1) Back Cushion (1)
D1

6
Parts List
1” Big Screws (2) 1-1/2” Big Screws (2)
1-1/4” Small Screws (8) Plastic Caps (8)
Allen Key (1)

Step 1
Place the Star Base (B) upside down and insert 5 Casters (A)
into the holes on the Star Base (B).
7
B
A

Step 2
Turn the Star Base (B) over and insert the Gas Lift with Telescoping
Cover (C) through the center hole on top of Star Base (B).
8
B
C

Step 3
Place the Back Cushion (G) between Arms (E1 & E2) and use
1-1/4" Small Screws (J) to fasten screws on both the arms and
back cushion.
Do not tighten the screws completely! Please keep levers to the
down position for easy assembling.
9
E1
E2
L
J
G

Step 4
Place Seat Cushion (F) between Arms (E1 & E2), and use 1-1/4"
Small Screws (J) to fasten screws on both the arms and seat
cushion. Note: Tighten all the screws completely.
10
E1
E2
G
L
F
J

Step 5
Attach Seat Plate (D) to the bottom of the Seat Cushion (F)
(with the front of the seat plate facing the front of seat cushion).
Attach by using 1-1/2” Big Screws (I) for the front holes of the
Seat Plate (D) and 1” Big Screws (H) for the rear holes of the
Seat Plate (D) and tighten screws.
Note: Tighten the screws completely.
11
D
F
I
H
L

Step 6
Insert Lever (D1) of Seat Plate (D) to the pre-attached cable
lever receiver on the underside of Seat Cushion (F) (with the
front of the lever facing the front of seat cushion). Push down
the key on the receiver to pull out the lever.
12
Insert Push
Disassemble the lever
Assemble t he lever
Insert
F
D1

Step 7
Lift the lids of the EZ cable connectors as shown. Insert the ends
of the arm cables into the grooves of the EZ cable connectors
and snap them into place as shown. Then close the lids.
Note: Connect the EZ cable connector of the back cushion to
the left arm cable, the seat plate to the right arm cable. Be
careful not to cross the cables. Finally fix the cables into the
plastic clips attached to the bottom of the seat cushion.
13
E1
E2
F
G
D
STEP 1:LIFT L I D
STEP 2:INSE R T ARMCAB L E
STEP 3:CLOS E LID
S T E P 1 : LI F T LI D
S T E P 2 : IN S E R T A R M C A B L E
S T E P 3 : CL O S E L I D
Lids/Tapas
EZ Cable/Cable EZ
Cable ends/
Puntas de cable

Step 8
Position the assembled chair upright with the Seat Plate (D)
facing down. Insert the Gas Lift with Telescoping Cover (C) into
the center hole of the Seat Plate (D) and press down until fully
engaged.
14
D
C
F

Step 9
Press the Plastic Caps (K) into armrest holes once all screws
have been tightened.
15
K
K

Operating Instructions
Function Instruction - 1
To Adjust Seat Height:
While seated, lean forward and reach under the right side of
the arm to find the lever. Lift the lever and raise your body up
slightly to allow the chair to rise to the desired height. Once
desired height is reached, release lever to lock chair at
desired height. To lower the seat, lift the lever while seated.
The chair will descend until the lever is released or the chair
reaches the bottom position.
16

17
Operating Instructions
Function Instruction - 2
To Operate Tilt Lockout:
While seated, reach under the left side of the arm to find the
lever. Push up the lever and lean back to allow the chair to tilt
backwards. To lock the chair in the upright or vertical position,
sit upright and pull the lever to the down position.

Operating Instructions
Function Instruction - 3
To Adjust Tension On The Tilt:
Reach under the front center of the chair, grasp the round knob
(R) and turn it counter- clockwise to stiffen the tilt mechanism for
a heavier user. Turn the knob (R) clockwise to loosen the tilt
mechanism for a lighter user. Rotate the knob (R) until the desired
resistance is reached.
18
R

Operating Instructions
Function Instruction - 4
Adjusting to 360 Motion Support:
While seated, the 3D lumbar can dynamically provide continu-
ous support by connecting with your body's natural movement.
The 3D lumbar conforms to the curve of your spinal cord and is
intended to relieve your back from stress.
19

Operating Instructions
Function Instruction - 5
360˚ Swivel:
360˚ seat swivel.
20