Seville Classics 20185 User manual

TR180321
ASSEMBLY INSTRUCTIONS
UltraHD Rolling Cabinet (Model No. 20185)
28in. W x 25in. D x 34.5in. H
(71.1cm x 63.5cm x 87.6cm )
Reference page 15 for special care and
maintenance of stainless steel

(pg 1 of 16)

(pg 2 of 16)
Small Drawer
Medium Drawer
Large Drawer
#12-3
#12-2

(pg 3 of 16)
(#7) UPPER BACK PANEL x 1 PC
(#8) DOOR x 1 PC
(#5) MIDDLE PANEL x 1 PC
(#6) BOTTOM BACK PANEL x 1 PC
(#1) BOTTOM PANEL x 1 PC
(#2) FRONT FRAME x 1 PC
Please check the parts carefully according to the parts list. If you are missing any parts, please
contact our customer service department (please refer to page 16 of 16).
PARTS LIST
(#4) LEFT PANEL x 1 PC
(#3) RIGHT PANEL x 1 PC

(pg 4 of 16)
(#12-1) SMALL DRAWER FRONT PANEL x 2 PCS
(#11) PUSH BAR x 1 PC
(#12-4) SMALL DRAWER BACK PANEL x 2 PCS
(#12-5) SMALL DRAWER BASE PANEL x 3 PCS
(#12-2) LARGE/SMALL DRAWER LEFT PANEL x 3 PCS
(#12-3) LARGE/SMALL DRAWER RIGHT PANEL x 3 PCS
(#9) MIDDLE SHELF x 1 PC
(#10) STAINLESS STEEL TOP x 1 PC
Please check the parts carefully according to the parts list. If you are missing any parts, please
contact our customer service department (please refer to page 16 of 16).
PARTS LIST

(pg 5 of 16)
PARTS LIST
(#13-4) MEDIUM DRAWER BACK PANEL x 1 PC
(#16-5) LARGE DRAWER BACK PANEL x 1 PCS
(#14) SWIVEL WHEEL WITH BRAKE x 2 PCS
(#16-1) LARGE DRAWER FRONT PANEL x 1 PC
(#16-4) LARGE DRAWER BOTTOM PANEL x 1 PC
(#13-3) MEDIUM DRAWER RIGHT PANEL x 1 PCS
(#13-1) MEDIUM DRAWER FRONT PANEL x 1 PC
(#13-2) MEDIUM DRAWER LEFT PANEL x 1 PC
Please check the parts carefully according to the parts list. If you are missing any parts, please
contact our customer service department (please refer to page 16 of 16).

(pg 6 of 16)
(#19) LEFT BACK CORNER PROTECTOR x 1 PC
(#18) RIGHT BACK CORNER PROTECTOR x 1 PC
(#21) SCREW B (M4 x 8) x 96 PCS
(#20) SCREW A (M4 x 10) x 60 PCS
(#22) DOOR / DRAWER KEY x 4 STRINGS
(#23) HOOK x 4 PCS
Please check the parts carefully according to the parts list. If you are missing any parts, please
contact our customer service department (please refer to page 16 of 16).
PARTS LIST
(#15) SWIVEL WHEEL W/O BRAKE x 2 PCS
(#17) BUMPER x 4 PCS

(pg 7 of 16)
(#24) SCREWDRIVER x 1PC
(#25) SCREW D (M8 x 18) x 16 PCS
PARTS LIST
(#26) SCREW C (M4 x 18) x 16 PCS
(#27) Middle Crossbar x 1 PC
(#28) LARGE DRAWER MAT x 1 PC
(#29) SMALL DRAWER MAT x 3 PCS
Please check the parts carefully according to the parts list. If you are missing any parts, please
contact our customer service department (please refer to page 16 of 16).

TIP:
Step 1.
Step 2.
Step 3.
Locate the Front Frame (#2) and attach to the "Front"
of the Stainless Steel Top (#10) using Screw Driver
(#24) and Screw A (#20).
Note: The screw holes have some tolerance so make
sure that the top and sides of the Front Frame are
flushed with the Stainless Steel Top – this may save
time by avoiding having to make slight adjustments
later.
Install the Left Panel (#4)
Attach the Left Panel (#4) to Front Frame (#2) and
Stainless Steel Top (#10). Make sure the “Top” of the
Left Panel (#4) is on the Stainless Steel Top (#10) and
the screw holes are lined up to the Front Frame (#2).
Use Screw Driver (#24) and Screw A (#20) to tighten
the Left Panel (#4) to the Front Frame (#2) and
Stainless Steel Top (#10).
ASSEMBLY INSTRUCTIONS (pg 8 of 16)
UltraHD Rolling Cabinet (Model No. 20185)
A magnetic screwdriver is included for your
convenience. If a power screwdriver is used, keep on
a low torque setting.
Open the package, remove and place all parts to the
side. Then open the package of the Stainless Steel Top
(#10).
Note: The Stainless Steel Top is packed within an
inner cardboard box. Assemble on top of the
cardboard to help avoid scratching the stainless steel
top.
Install Front Frame (#2)

Step 4.
Step 5.
Install the Bottom Panel (#1).
Step 6.
Attach the Bottom Panel (#1) to the Left Panel (#4),
Right Panel (#3), Front Frame (#2) and Bottom Back
Panel (#6). Line up the screw holes and use Screw A
(#20) to tighten.
ASSEMBLY INSTRUCTIONS (pg 9 of 16)
UltraHD Rolling Cabinet (Model No. 20185)
Install the Right Panel (#3)
Attach the Right Panel (#3) to Front Frame (#2). Make
sure the “Top” of the Right Panel (#3) is on the
Stainless Steel Top (#10). Use Screw Driver (#24) and
Screw A (#20) to tighten the Right Panel (#3) to the
Front Frame (#2)and Stainless Steel Top (#10).
Install the Upper Back Panel (#7) and Bottom Back
Panel (#6)
a. Attach the Upper Back Panel (#7) between the Left
Panel (#4) and Right Panel (#3). Make sure the “Top”
of the Upper Back Panel (#7) is on the Stainless Steel
Top (#10) as the sticker indicates. Line up the screw
holes and use Screw A (#20) to tighten up the Upper
Back Panel to the Stainless Steel Top (#10), Left Panel
(#4) and Right Panel (#3).
b. Attach Bottom Back Panel (#6) between the Left
Panel (#4) and Right Panel (#3). Make sure the “Top”
of the Bottom Back Panel (#6) is on the Upper Back
Panel (#7) as the sticker indicates. Line up the screw
holes and use Screw A (#20) to tighten the Bottom
Back Panel (#6) to the Upper Back Panel (#7), Left
Panel (#4) and Right Panel (#3).

Step 7.
Step 8.
Step 9.
ASSEMBLY INSTRUCTIONS (pg 10 of 16)
UltraHD Rolling Cabinet (Model No. 20185)
Install Wheels (#14 and #15)
Attach Wheels (#14 and #15) to the Bottom Panel (#1)
and surrounding frame. Make sure the Swivel Wheels
with Brake are installed at the front side. Use Screw D
(#25) to tighten them.
Install Bumpers (#17)
Attach Bumpers (#17) to the bottom four corners of
the cabinet. Use Screw C (#26) to tighten them.
Install the Middle Panel (#5)
Install the middle panel as the left photo show. Use 2
pcs of Screw A (#20) to tighten with the Bottom Panel
(#1).
Front
Back

Step 10.
Note:
Step 11.
Attach the Push Bar (#11) and Back Corner
Protection (#18 and #19)
Attach the Push Bar (#11) to the front side
of the cabinet. Use 8 pcs of Screw A (#20)
to tighten. Then attach the Right Back
Corner Protection (#18) to the right side of
the cabinet and Left Back Corner Protection
(#19) to the left side of the cabinet. Use 10
pcs of Screw A (#20) to tighten them.
ASSEMBLY INSTRUCTIONS (pg 11 of 16)
UltraHD Rolling Cabinet (Model No. 20185)
Lift the Storage Cabinet upright, fix the Middle Panel (#5) with the Upper
and Bottom Back Panel (#6 & #7) using 3 pcs of Screw A (#20) to tighten.
Install Middle Crossbar (#27)
Install the Middle Crossbar (#27) with the
Left Panel (#4) and Middle Panel (#5) as the
left photo shows. Use Screw A (#20) to
tighten.
Make sure the inner side of the Middle
Crossbar is faceing upward

Step 12:
Step 13:
Step 14:
ASSEMBLY INSTRUCTIONS (pg 12 of 16)
UltraHD Rolling Cabinet (Model No. 20185)
Install Large Drawer Base Panel (#16-4)
Fit and attach Large Drawer Base Panel (#16-4) into
the back slot of stainless steel Drawer Front (#16-1),
use Screw B (#21) to tighten.
Install Large Drawer Side Panel (#12-2 & #12-3)
Attach Large Drawer Side Panels (#12-2 and #12-3)
to the back of Drawer Front (#16-1). Make sure the
Drawer Side Panels (#12-2 and #12-3) are placed all
the way into the slot, making contact with the inner
wall of the front panel. Line up the screw holes and
use Screw B (#21) to tighten them.
Install Large Drawer Back Panel (#16-5).
Attach the Large Drawer Back Panel (#16-5) to the
rest of the assembled drawer. Use Screw B (#21) to
tighten.
#16-1

Step 15：
Step 16.
Step 17.
NOTE:
Step 18.
ASSEMBLY INSTRUCTIONS (pg 13 of 16)
Install Small Drawer Side Panels (#12-2 and #12-3).
Fit and attach Small Drawer Side Panels (#12-2 and #12-3) one
at a time into the back of the Small Drawer Front Panel (#12-
1). Make sure the Drawer Side Panels are placed in all the way
making contact with the rear of the Small Drawer Front Panel
(#12-1). Line up the screw holes and use Screw B (#21) to
tighten them.
Install Small Drawer Base Panel (#12-5).
From above, fit and attach Small Drawer Base Panel (#12-5)
between the two sides and into the back of the Small Drawer
Front Panel (#12-1). Use Screw B (#21) to tighten.
Note: Do not fully tighten any one screw until all screws are
partially screwed in.
UltraHD Rolling Cabinet (Model No. 20185)
Attach the Small Drawer Back Panel (#12-4) to the rest of the
assembled drawer. Use Screw B (#21) to tighten.
Once you have the first Small Drawer assembled, repeat
Steps 15-17 to assemble the other two Small Drawers.
Once completed, you should have three Small Drawers.
Assemble and Install Medium Drawer the same way.
Repeat Steps 15-17 using Medium Drawer Left Panel (#13-2),
Medium Drawer Right Panel (#13-3), Medium Drawer Front
Panel (#13-1), Medium Drawer Back Panel (#13-4) and Drawer
Base Panel (#12-5) to assemble the Medium Drawer. Once
assembled, you should have one Medium Drawer.
Install Small Drawer Back Panel (#12-4).
#12-1

Step 19.
Note: The Medium Drawer is at the bottom
The oval hole at the front of the slider allows for the gaps
between the drawers to be adjusted. Make the adjustments
once all the drawers are installed
ASSEMBLY INSTRUCTIONS (pg 14 of 16)
UltraHD Rolling Cabinet (Model No. 20185)
Place the Small and Large Drawers (#12)(#16)
Pull out the sliders completely, then attach the
drawer to the sliders. Make sure the square holes
on the drawer side panels are line up, and the
drawer is hooked onto the sliders completely.
Use 4pcs Screw B (#21) to tighten the drawer, and
put the Drawer Mat (#28) and (#29) into the
drawer.
Repeat Step 19 to place the rest of the drawers

Step 19.
Step 20.
Install the Door Panel (#8)
Attach the Door (#8) to the unit using
Screw B (#21) to tighten.
Note: The screw holes on the door hinge have
tolerance, enabling the door to be adjusted and
centered in the door frame.
Stainless Steel Maintenance:
These parts have an UltraGuard® fingerprint resistant finish. Do
not use traditional stainless steel cleaners on this unit. Lightly
wipe off once a month with clean warm water and a soft cloth
(preferably a microfiber cloth). This is the safest formula to
prevent new stains from appearing over time and manage
unwanted fingerprints or grease marks. Remember to always
wipe in the direction of the surface grain (NEVER ACROSS) and
always use a lint-free cloth. Once the surface is
clean,thoroughly wipe dry with a soft absorbent cloth.
ASSEMBLY INSTRUCTIONS (pg 15 of 16)
UltraHD Rolling Cabinet (Model No. 20185)
Install the Shelf (#9).
a. Decide the height for the Middle Shelf (#9), place the Hooks (#23) into the hook slots and push down.
Note: The Middle Shelf has 4 Hooks at four corners for support. Place the 4 Hooks at the four corners
and make sure they are the same height.
b. Place the Middle Shelf (#9) into the cabinet and push down onto the Hooks (#23).

***Please visit our website or call and inquire about our additional UltraHD Line***
CONTACT INFORMATION (pg 16 of 16)
*If you are missing any parts, have any questions, or need additional assistance in assembly, please contact
our bilingual (English and Spanish) customer service department at:
Seville Classics, Inc.
19401 South Harborgate Way
Torrance, CA 90501
USA
Telephone: [phone] within USA
Hours: 9:00am - 4:30pm (Pacific Standard Time)
Fax: [phone]
E-mail: [email protected]
Website & Online Store: www.sevilleclassics.com
UltraHD Line
Model No. 16238
UltraHD Storage Cabinet
Model No. 16236
UltraHD Storage Cabinet
Model No. 20238
UltraHD Rolling Cabinet
Model No. 20184
UltraHD 6-Drawer Rolling Cabinet

Model No. 20296
UltraHD Height Adjustable Workbench
Model No. 20217
UltraHD Trash Bin
Model No. 20255
UltraHD Tool Box
UltraHD Line
Model No. 20230
UltraHD Wall Cabinet
Model No. 20262
UltraHD Rolling Workbench
Model No. 20283
UltraHD Mobile Work Table