Seville Classics UltraHD 20262 User manual

ASSEMBLY INSTRUCTIONS
UltraHD® 2-Door Rolling Workbench
(Model No. 20262, 20142, 20152)
77 in. W x 20 in. D x 37.5 in. H
(1.95 m W x 50.8 cm D x 95.2 cm H)
Granite Graphite Red
Reference page 15 for special care
and maintenance of stainless steel
TR200221

1
Large
Drawer
Medium
Drawer
Small
Drawers
#24
#26
#12
#13
#20-A #18 #20-B #19 #3 #17
#13-B
#42
#57
#2
#9
#4
#40
#8
#6
#11
#27
#5
#23
#15
#1
#27-B
#41
#12-B
2

Small Drawer
Medium Drawer
Large Drawer
#13-4
#13-2
#15
#13-1
#12-1
#12-5
#12-2
#15
#26-1
#26-2
#15
3

(#1) LEFT SIDE PANEL x 1 PC
(#2) RIGHT SIDE PANEL x 1PC
PARTS LIST
Please check the parts carefully according to the parts list. If you are missing any parts, please contact our
customer service department (please see page 15.)
(#4) BACK FRAME x 1 PC
(#3) FRONT FRAME x 1 PC
(#8) SOLID HARDWOOD TOP x 1 PC
(#9) PUSH BAR x 2 PCS
(#5) BASE PANEL x 1 PC
(#6) SHELF x 1 PC
34

(#12-5) MEDIUM-SIZE DRAWER BACK PANEL x 1 PC
(#12-2) MEDIUM-SIZE DRAWER BOTTOM PANEL x 1 PC
(#13-1) LARGE DRAWER FRONT PANEL x 1 PC
(#13-2) LARGE DRAWER BOTTOM PANEL x 1 PC
(#12-B) WHEEL WITH BRAKE x 2 PCS
(#13-B) WHEEL W/O BRAKE x 2 PCS
(#11) LEFT SIDE SLIDER SUPPORT x 1PC
(#12-1) MEDIUM-SIZE DRAWER FRONT x 1 PC
5
PARTS LIST
Please check the parts carefully according to the parts list. If you are missing any parts, please contact our
customer service department (please see page 15.)

(#13-4) LARGE DRAWER BACK PANEL x 1 PC
(#15) SCREW B (M4 x 8L) x 195 PCS
(#20-B) RIGHT DOOR x 1PC
(#21) SCREW DRIVER x 1 PC
(#18) LEFT DOOR HINGE x 2PCS
(#17) SCREW D ( M8 x 18L) x 16 PCS
(#19) RIGHT DOOR HINGE x 2PCS
(#20-A) LEFT DOOR x 1PC
6
PARTS LIST
Please check the parts carefully according to the parts list. If you are missing any parts, please contact our
customer service department (please see page 15.)

(#27-B) WASHER (M8) x 6 PCS
(#40) SCREW E (M8 x 18L) x 6 PCS
(#22) KEY x 6 PCS
(#24) DRAWER MAT x 11 PCS
(#25) WRENCH x 1 PC
(#26-1) SMALL DRAWER FRONT x 9 PCS
(#26-2) SMALL DRAWER CASE x 9 PCS
(#27) RIGHT SIDE SLIDER SUPPORT x 1 PC
M8X20 pcs
7
PARTS LIST
Please check the parts carefully according to the parts list. If you are missing any parts, please contact our
customer service department (please see page 15.)

(#41) SCREW F (M4 x 8L) x 32 PCS
(#42) SCREW G (M4 x 30L) x 16 PCS
(#57) BUMPER x 4 PCS
(#23) MAGNET x 1 PC
78
PARTS LIST
Please check the parts carefully according to the parts list. If you are missing any parts, please contact our
customer service department (please see page 15.)

TIP:
Step 1.
Step 2.
Step 3.
Once the Left Side Panel (#1) is securely fastened,
test the slider to make sure it extends in the correct
direction (Away from the Back Frame (#4).
UltraHD® 2-Door Rolling Workbench (Model No. 20262, 20142, 20152)
A magnetic screwdriver is included for your
convenience. If using a powered screwdriver, keep
torque setting on LOW.
Open both boxes.Remove the cardboard box
containing the Solid Hardwood Top (#8) and set the
other parts to the side.
Leave the Hardwood Top (#8) on top of cardboard
to reduce the chance of scratching during assembly.
Install Back Frame (#4) to Solid Hardwood Top (#8).
[Use the Wrench (#25) for this step]
Place the Back Frame (#4) as the left picture shows
and use 3 pcs Screw E (#40) and Washers (#27-B) to
fasten. Attach the "Top" of the Back Frame (#4), as
indicated by the attached sticker, to the Solid
Hardwood Top (#8) (The Solid Hardwood Top has
no set front or back end).
Make sure the back and side are flush with the
Solid Hardwood Top. Do not tighten any screws
completely until all screws for that part have been
partially screwed in.
Install Left Side Panel (#1).
Attach Left Side Panel (#1) to Back Frame (#4),
making sure the "Top" of Left Side Panel (#1) is on
the Solid Hardwood Top (#8). Use 3 pcs of Screw B
(#15) and Screw Driver (#21) to fasten.
9
*NOTE: We recommend using TWO people to assemble the workbench.
NOTE:
#
8
NOTE:
NOTE:

Step 7.
10
UltraHD® 2-Door Rolling Workbench (Model No. 20262, 20142, 20152)
*NOTE: We recommend using TWO people to assemble the workbench.
#11 #15
#15
#27
#15
#2
#3
#15
#27- B
#40
Step 4.
Step 5.
Step 6.
Install Left Side Slider Support (#11)
Attach the Left Side Slider Support (#11) to the
Back Frame (#4), make sure the "Top" of Left
Side Sli der Support (#11) is close to the Solid
Hardwood Top (#8 ). The “Top” is indicated by a
sticker on one of th e vertical columns.
Use 3 pcs of Screw B (#15) and Scr ewdriver (#21)
to fasten.
The Drawer Slides will face those on the Left
Side Panel (#1) .
Install Right Side Slider Support (#27)
Attach the Right Side Slider Support (#27) to the
Bac k Frame (#4), make sure the "Top" of Right
Side Sli der Support (#27) is close to the Solid
Hardwood Top(#8 ). The “Top” is indicated by a
sticker on one of th e vertical columns.
Use 2 pcs of Screw B (#15) and Scr ewdriver (#21)
to fasten.
The Drawer Slide will face those on the Right
Side Panel (#2).
Install the Right Side Panel (#2).
Attach the Right Side Panel (#2) to the Back
Frame (#4 ), make sure the "Top" of Right Side
Panel (#2) is close t o the Solid Hardwood Top(#8).
The “Top” is indicated by a sticker on one of the
vertical columns. U se 3 pcs of Screw B (#15) and
Screw Driver (#21) to fasten.
Install the Front Frame (#3).
A: Attach the "Top" of the Front Frame (#3) to the
Solid Hardwood Top (#8). The other screw holes
will align with the Left and Right Side Panels (#1
and #2), Left Side Slider Support (#11) and Right
Side Slider Support (#27).
B: Use 11 pcs of Screw B (#15) and Screwdriver
(#21) to fasten the Front Frame (#3) on the Left
and Right Side Panels (#1 and #2), Left Side Slider
Support (#11) and Right Side Slider Support (#27).
C: Make sure the four edges of the Cabinet are
aligned, then fasten the Front Frame (#3) on the
Solid Hardwood Top (#8) by using 3 pcs of Washer
(#27-B) and Screw E (#40) with Wrench (#25).
The ball bearing track will have to be pulled out
1" to expose the screw holes used for fastening
to the Front Frame #3.
Note:
Note:
Note:

Step 8.
Step 10.
Attach Bumpers (#57) to the bottom four corners of
Workbench. Use 16 pcs of Screw G (#42) to fasten.
Then, rotate/stand the Workbench upright.
Step 11.
A: Attach Push Bars (#9) on both the Left and Right Side
Panels (#1 and #2). Use 24 pcs of Screw F (#41) to fasten.
B: Use 2 pcs of Screw B (#15) to fasten the Magnet (#23)
on the Front Frame (#3)
Attach Wheels (#12-B and #13-B)using 16 pcs of
Screw D (#17). Make sure that the Wheels w/o
Brakes (#13-B) are on the same end (right or left
side) of the Workbench.
There is some tolerance in the holes of the
wheel frame, so make sure that the two wheels
w/o brakes are parallel to each other and to the
frame of the unit.
Step 9. Install Wheels (#12-B and #13-B) .
Install Base Panel (#5)
Attach Base Panel (#5) to the rest of the unit
as the left picture shows. Use 14 pcs of Screw
B (#15) and Screw Driver (#21) to fasten.
11
UltraHD® 2-Door Rolling Workbench (Model No. 20262, 20142, 20152)
*NOTE: We recommend using TWO people to assemble the workbench.
#5
#15
#17
#12- B
#13- B
#57
#42
#41
#9
#23
#15
Note:

Step 12.
Step 13.
Assemble Large Drawer (#13) the same way.
Repeat Step 13 and Step 14, but using Large Drawer
Front Panel (#13-1), Large Drawer Bottom Panel (#13-2)
and Large Drawer Back Panel (#13-4).
A. Fold the Left and Right panel of the Medium Drawer
Bottom Panel (#12-2) up so that the ball bearing track
will attached to the outside of the drawer.
B. Attach the Medium-size Drawer Back Panel (#12-5) to
the folded drawer panel, use 7 pcs Screw B (#15) to
tighten.
lnstall Medium Drawer Bottom Panel (#12-2) and
Medium Drawer Back Panel (#12-5).
lnstall Medium Drawer Front (#12-1) .
From above, align the folded Drawer Panel with the
Medium Drawer Front (#12-1) as detail picture shows,
use 7pcs Screw B (#15) to tighten.
Do not fully tighten the screws. This will help you
make any adjustments to alignment later.
#12-2
#15
#12-5
#15
#12-1
#13-4
#13-2
#13-1
12
UltraHD® 2-Door Rolling Workbench (Model No. 20262, 20142, 20152)
*NOTE: We recommend using TWO people to assemble the workbench.
Note:

Note: Once all the drawer panels are aligned,
tighten all the drawer screws.
B. Slide the Left and Right Drawer Panel into Small
Drawer Front (#26-1) as the detail picture shows.
Use 7pcs Screw B (#15) to tighten.
#26-2
#26-2
#15
#26-1
#15
13
UltraHD® 2-Door Rolling Workbench (Model No. 20262, 20142, 20152)
*NOTE: We recommend using TWO people to assemble the workbench.
Step 14. A. Fold up all three panels of the Small Drawer
Body (#26-2).
Use Screw B (#15) to tighten the back panel to
the left and right panel.
Note: Do not tighten the screws all the way,
until part B is completed.

Step 15.
A. Pull out the sliders completely, then attach
the drawer to the sliders. Make sure the square
holes on the drawer side panels are line up,
and the drawer is hooked onto the sliders
completely.
B. Use 4pcs Screw B (#15) to tighten the
drawer, and put the Drawer Mat (#24) into the
drawer.
Repeat above steps to place other drawers.
Note: Do not tighten any screws completely
until all the drawers are adjusted well.
Only open one drawer at a
time to avoid tipping. 40 lbs.
maximum loading for each
drawer.
Place the Drawers.
Note: Pull out the ball
bearing track completely
before you attach drawer.
Hook cutaway view
The oval hole at the front of the
slider allows for the gaps between
the drawers to be adjusted. Make
the adjustments once all the
drawers are installed.
CAUTION
#15
#24
#13
14
UltraHD® 2-Door Rolling Workbench (Model No. 20262, 20142, 20152)
*NOTE: We recommend using TWO people to assemble the workbench.

Step 16.
Step 17. Install the Left Door (#20-A) and Right Door
(#20-B).
A. Insert 2 pcs of Left Door Hinge (#18) on to
the Left Door (#20-A). Insert 2 pcs of Right
Door Hinge (#19) on to the Right Door (#20-B).
B. Attach the Left Door (#20-A) to the left side
of the door frame and Right Door (#20-B) to
the right side of the door frame. Use 8 pcs
Screw F (#41) to fasten.
Note: The door hinge screw holes have
tolerance, enabling the doors to be adjusted
and centered in the frame.
Install the Shelf (#6).
Place the Shelf (#6) in the unit at the desired
height and ensure that all four corners are
secured on the hooks on the front and back
frame.
#6
#18
#20-A
#19
#20-B
#41
15
UltraHD® Stainless Steel Care Instructions
The stainless-steel parts of this product are protected with an UltraGuard™ fingerprint resistant finish.
DO NOT use traditional stainless-steel cleaners. To safely manage unwanted fingerprints and prevent new stains,
perfom the following steps once monthly:
• Lightly wipe with warm water and clean microfiber cloth
• Always wipe in the direction of the surface grain (NEVER ACROSS)
• Wipe away excess water with dry clean cloth
UltraHD® Wood Top Care Instructions
Our tops are made with real wood, and while great care is taken to ensure consistent top color and graining,
there may be natural variations between finished products. We hand select the wood for every top to ensure
the material is undamaged and naturally beautiful. If the wood top is received with excessive damage or
splitting, Seville Classics will guarantee replacement of the top. Variations of color, and minor scratches in the
clear coat finish will not be reason for replacement.
Restore Shallow Scratches or Chips
The wood surface of this product is finished with a polyurethane coat. If the wood top becomes chipped or
scratched, a polyurethane coat can be reapplied to restore a smooth texture and protect from future damage.
• Please follow the manufacturer's instruction on the product for application.
UltraHD® 2-Door Rolling Workbench (Model No. 20262, 20142, 20152)
*NOTE: We recommend using TWO people to assemble the workbench.

16
CONTACT INFORMATION
*If you are missing any parts, have any questions, or need additional assistance in assembly, please contact our bilingual
(English and Spanish) customer service department at:
Seville Classics, Inc.
19401 Harborgate Way Torrance, CA 90501 USA
Telephone: [phone] within USA
Fax: [phone]
Hours: 9:00am - 4:30pm (Pacific Standard Time)
E-mail: [email protected]
Website & Online Store: www.sevilleclassics.com
***Please visit our website or call and inquire about our additional UltraHD Line***
UltraHD® Line
UltraHD® Tall Storage Cabinet UltraHD® Mega Rolling Cabinet
Model No. 16236 (Granite)
Model No. 20143 (Graphite)
Model No. 20153 (Red)
Model No. 20133 (White)
Model No. 16238 (Granite)
Model No. 20148 (Graphite)
Model No. 20158 (Red)

UltraHD® Wall Cabinet with Open Shelf
Model No. 20217
UltraHD® Trash Bin
UltraHD® Lighted Workcenter
UltraHD® 2-Door Rolling Workbench
UltraHD® 6-Foot Height Adjustable Workbench
UltraHD® Line
UltraHD® 4-Drawer Rolling Cabinet
Model No. 20205 (Gray) Model No. 20296 (Granite)
Model No. 20141 (Graphite)
Model No. 20230 (Granite)
Model No. 20246 (Graphite)
Model No. 20150 (Red)
Model No. 20262 (Granite)
Model No. 20142 (Graphite)
Model No. 20152 (Red)
Model No. 20247 (Granite)
Model No. 20246 (Graphite)
Model No. 20157 (Red)