Seville Classics UltraHD 20110 User manual

ASSEMBLY INSTRUCTIONS
UltraHD® 60" Rolling Workbench (Model No. 20110, 20111)
60 in. W X 20 in. D X 37.5 in. H
(
152.4cm W x 50.8cm D x 95.2cm H)
Granite Graphite
Reference page 11 for special care and
maintenance of stainless steel
TR230525

#1
#41
#12-B
#13-B
#2
#17
#23
#3
#11
#27
#4
#8
#27-B
#40
#9
#5
#57
#42
#6
#7
#29
#20-B
#19
#20-C
#18
#20-A #19-A
#26
#24
#26-1
#26-2
#15
1
#1
#41
#12-B
#13-B
#2
#17
#23
#3
#11
#27
#4
#8
#27-B
#40
#9
#5
#57
#42
#6
#7
#29
#20-B
#19
#20-C
#18
#20-A #19-A
#26
#24
#26-1
#26-2
#15
#1
#41
#12-B
#13-B
#2
#17
#23
#3
#11
#27
#4
#8
#27-B
#40
#9
#5
#57
#42
#6
#7
#29
#20-B
#19
#20-C
#18
#20-A #19-A
#26
#24
#26-1
#26-2
#15
1

Please check the parts carefully according to the parts list. If you are missing any parts, please contact our customer
service department. (Please refer to page 12).
PARTS LIST
(#1) LEFT SIDE PANEL x 1 PC (#2) RIGHT SIDE PANEL x 1PC
2
(#7) RIGHT SHELF x 1 PC
(#8) SOLID HARDWOOD TOP x 1 PC
(#5) BASE PANEL x 1 PC (#6) LEFT SHELF x 1 PC
(#4) BACK FRAME x 1 PC(#3) FRONT FRAME x 1 PC
(#7) RIGHT SHELF x 1 PC
(#8) SOLID HARDWOOD TOP x 1 PC
2

Please check the parts carefully according to the parts list. If you are missing any parts, please contact our customer
service department. (Please refer to page 12).
PARTS LIST
(#11) LEFT SIDE SLIDER SUPPORT x 1 PC (#9) PUSH BAR x 2 PCS
(#20-C) MIDDLE DOOR x 1 PC(#20-A) LEFT DOOR x 1 PC
(#12-B) WHEEL WITH BRAKE x 2 PCS (#13-B) WHEEL W/O BRAKE x 2 PCS
(#20-B) RIGHT DOOR x 1 PC (#29) CASTER SEAT CUSHION x 4 PCS
3

Please check the parts carefully according to the parts list. If you are missing any parts, please contact our customer
service department. (Please refer to page 12).
PARTS LIST
(#23) MAGNET x 1 PC (#27) RIGHT SIDE SLIDER SUPPORT x 1 PC
(#26-2) SMALL DRAWER CASE x6 PCS (#24) DRAWER MAT x 6 PCS
(#18) LEFT DOOR HINGE x 2 PCS(#19-A) LEFT SIDE DOOR HINGE x 2 PCS
(#19) RIGHT DOOR HINGE x 2PCS (#26-1) SMALL DRAWER FRONT x 6 PCS
4

Please check the parts carefully according to the parts list. If you are missing any parts, please contact our customer
service department. (Please refer to page 12).
PARTS LIST
(#57) BUMPER x 4 PCS (#25) WRENCH x 1 PC
(#17) SCREW D ( M8 x 18L) x 16 PCS (#15) SCREW B (M4 x 8L) x 78 PCS
5
(#21) SCREW DRIVER x 1 PC (#22) KEY x 4 PCS
(#41) SCREW F (M4 x 8L) x 70 PCS (#42) SCREW G (M4 x 30L) x 16 PCS
(#27-B) WASHER (M8) x 6 PCS (#40) SCREW E (M8 x 18L) x 6 PCS
5

TIP:
Step 1
.
Step 2.
UItraHD® Rolling Workbench (Model No. 20110, 20111)
Install Back Frame (#4) to Solid Hardwood Top
(#8).
*NOTE: We recommend using TWO people to assemble the workbench.*
Open both boxes, locate and remove the
cardboard box containing the Solid Hardwood
Top (#8). Set the other parts to the side.
When assembling this item, place the Solid
Hardwood Top up side down on the cardboard to
avoid scratching the top surface.
A magnetic screwdriver is included for your
convenience. If a power screwdriver is used,
keep on a low torque setting.
[Use the Wrench (#25) for this step]
#8
#25
#40
6
Step 3
.
Attach Left Side Panel (#1) to Back Frame (#4),
making sure the "Top" of Left Side Panel (#1) is
on the Solid Hardwood Top (#8). Use 3 pcs of
Screw F (#41) and Screw Driver (#21) to fasten.
Install Left Side Panel (#1).
[Use the Wrench (#25) for this step]
Place the Back Frame (#4) as the left picture
shows and use 3 pcs of Screw E (#40) and
Washers (#27-B) to fasten. Attach the "Top" of
the Back Frame (#4), as indicated by the attached
sticker, to the Solid Hardwood Top (#8). The Solid
Hardwood Top has no set front or back end.
Note: Ensure the back and side are flush with
the Solid Hardwood Top. When assembling a
part, do not tighten any screws completely until
all screws for that part have been partially
screwed in.
Tip: Once the Left Side Panel (#1) is securely fastened,
check to make sure the slider motion is operating in the
correct direction (Away from the Back Frame (#4).
#8
#1
#21#41
#8
#25
#27-B
#4
#40
#8
#8
#1
#21#41
#8
#25
#27-B
#4
#40
#8
6

Step 4.
Step 5.
UItraHD® Rolling Workbench (Model No. 20110, 20111)
Install Right Side Slider Support (#27)
*NOTE: We recommend using TWO people to assemble the workbench.*
Attach the Left Side Slider Support (#11) to the
Back Frame (#4), make sure the "Top" of Left
Side Slider Support (#11) is close to the Solid
Hardwood Top (#8). The "Top" is indicated by a sticker
on one of the vertical columns.
Use 3 pcs of Screw F (#41) and Screwdriver (#21)
to fasten.
Install Left Side Slider Support (#11)
Note: The Drawer Slides will face those on the Left
Side Panel (#1).
Attach the Right Side Slider Support (#27) to the
Back Frame (#4), make sure the "Top" of Right
Side Slider Support (#27) is close to the Solid
Hardwood Top (#8). The "Top" is indicated by a sticker
on one of the vertical columns.
Use 2 pcs of Screw F (#41) and Screwdriver (#21)
to fasten.
Note: The Drawer Slides will face those on the Right
Front
Back
#11
#41
#41
#27
7
Step 6.
Step 7
.
A: Attach the "Top" of the Front Frame (#3) to the
Solid Hardwood Top (#8). The other screw holes will
align with the Left and Right Side Panels (#1 and #2),
Left Side Slider Support (#11) and Right Side Slider
Support (#27).
B: Use 11 pcs of Screw F (#41) and Screwdriver
(#21) to fasten the Front Frame (#3) on the Left
and Right Side Panels (#1 and #2), Left Side Slider
Support (#11) and Right Side Slider Support (#27).
C: Make sure the four edges of the Cabinet are
aligned, then fasten the Front Frame (#3) on the
Solid Hardwood Top (#8) by using 3 pcs of Washer
Install the Front Frame (#3).
Install the Right Side Panel (#2).
Note: The Drawer Slides will face those on the Right
Side Panel (#2).
Attach the Right Side Panel (#2) to the Back
Frame (#4), make sure the "Top" of Right Side
Panel (#2) is close to the Solid Hardwood Top (#8). The
"Top" is indicated by a sticker on one of the vertical
columns. Use 3 pcs of Screw F (#41) and Screw Driver
(#21) to fasten.
#11
#41
#41
#27
#41
#2
#41
#40
#3
#27-B
Solid Hardwood Top (#8) by using 3 pcs of Washer
(#27-B) and Screw E (#40) with Wrench (#25).
#11
#41
#41
#27
#41
#2
#41
#40
#3
#27-B
7

Step 9.
Install caster seat cushion (#29) and Wheels
(#12-B and #13-B)
Attach 4pcs (#29) caster seat cushion and 4pcs
wheels (#12-B and #13-B) on the frame as
UItraHD® Rolling Workbench (Model No. 20110, 20111)
*NOTE: We recommend using TWO people to assemble the workbench.*
Step10.
Install Base Panel (#5)
Attach Base Panel (#5) to the rest of the unit
as the left picture shows. Use 10 pcs of Screw F
(#41) and Screw Driver (#21) to fasten.
#41
#5
#29
#17
#12-B
#13-B
8
wheels (#12-B and #13-B) on the frame as
shown in left picture, use the 16pcs (#17)
screws D to tighten them. Make sure that the
(#13-B) Fixed wheels w/o Brakes are on the
same end (right or left side) of the Work Bench.
Also the (#12-B) Swivel wheel with brake.
Step 11. Install Bumpers (#57)
Attach Bumpers (#57) to the bottom four corners of
Workbench. Use 16 pcs of Screw G (#42) to fasten.
Then, rotate/stand the Workbench upright.
Step 12. Install Push Bars (#9) and Magnet (#23)
A: Attach Push Bars (#9) on both the Left and Right Side
Panels (#1 and #2). Use 24 pcs of Screw F (#41) to
fasten.
B: Use 2 pcs of Screw F (#41) to fasten the Magnet (#23)
on the Front Frame (#3).
#42
#57
#41
#5
#9
#41
#23
#41
#29
#17
#12-B
#13-B
on the Front Frame (#3).
#42
#57
#41
#5
#9
#41
#23
#41
#29
#17
#12-B
#13-B
8

Step 13.
UItraHD® Rolling Workbench (Model No. 20110, 20111)
Note: Do not tighten the screws all the way,
until part C is completed.
*NOTE: We recommend using TWO people to assemble the workbench.*
A. Fold up all three panels of the Small Drawer
Body (#26-2).
B. Use 2pcs Screw B (#15) to tighten the back
panel to the drawer left and right panels.
#26-2
#26-2
9
until part C is completed.
NOTE: Once all the drawer panels are aligned,
tighten all the drawer screws.
C. Slide the Left and Right Drawer Panel into
Small Drawer Front (#26-1) as the detail picture
shows. Use 7pcs Screw B (#15) to tighten.
#26-2
#26-2
#15
#26-2
#26-2
#15
9

Step 14.
*NOTE: We recommend using TWO people to assemble the workbench.*
Place the Drawers.
Note: Pull out the ball
bearing track completely
before you attach drawer.
UItraHD® Rolling Workbench (Model No. 20110, 20111)
A. Pull out the sliders completely, then put the
drawer to the sliders, make sure the square
holes on the drawer side panels are line up,
and the drawer is hook on the sliders
completely as show left.
B. Use 4pcs of Screw B (#15) to tigthen on
drawer slides.
C. Repeat step 14, install the other 3pcs middle
drawers (#26).
D. Put 1pcs (#24) Drawer mat into each
drawer.
Note: After all drawers are installed, the gap
between the drawers is uneven, you can loosen
the screws on the inner rail and adjust the
drawer up and down.
10
Only open one drawer at a
time to avoid tipping. 30 lbs.
maximum loading for each
drawer.
Hook cutaway view
The oval hole at the front of
the slider allows for the gaps
between the drawers to be
adjusted. Make the
adjustments once all the
CAUTION
#26
#24
#15
drawer.
10

Step 15.
Step 16.
*NOTE: We recommend using TWO people to assemble the workbench.*
Install Left Shelf (#6) and Right Shelf (#7)
UItraHD® Rolling Workbench (Model No. 20110, 20111)
Install the Left Door (#20-A) and Middle Door
(#20-C), Right Door (#20-B).
Place the Left Shelf (#6) and Right Shelf (#7) in
unit at the desired height and ensure that all
four corners are secured on the hooks in the
front and back.
Note: The height of the shelf can be adjusted
according to the hook in the cabinet.
A. Insert 2 pcs of Left Side Door Hinge (#19-A) on
to the Left Door (#20-A). Insert 2 pcs of Left Door
Hinge (#18) on to the Middle Door (#20-C).
Insert 2 pcs of Right Door Hinge (#19) on to the
Right Door (#20-B).
B. Attach the Left Door (#20-A) to the left side of
the door frame and Middle Door (#20-C) to the
middle of the door frame and Right Door (#20-B)
to the right side of the door frame. Use 12 pcs
Screw F (#41) to fasten.
Note: The door hinge screw holes have
#6
#7
#20-A
#19-A
#18
#20-C
11
UltraHD® Wood Top
Although great care is taken to hand select consistent wood top color and grain for UltraHD® products, there can and will be natural
variations in color and graining between finished products. These variations contribute to the beauty of using a natural material as a
workbench and are considered standard quality. Variations of color within these standards and minor scratches in the clear coat
finish will not be a reason for replacement. If the wood top is received with excessive damage or splitting, Seville Classics® will
guarantee replacement of the wood top.
Restore Shallow Scratches or Chips
If the wood top becomes scratched and chipped over time or during assembly, a Polyurethane finish can be applied to help restore
the wood's natural texture, as well as protect the surface from future damage.
Stainless Steel Maintenance:
These parts have an UltraGuard® fingerprint resistant finish. Do not use traditional stainless steel cleaners on this unit. Lightly wipe
off once a month with clean warm water and a soft cloth (preferably a micro fiber cloth). This is the safest formula to prevent new
stains from appearing over time and manage unwanted fingerprints or grease marks. Remember to always wipe in the direction of
the surface grain (NEVER ACROSS) and always use a lint-free cloth. Once the surface is clean,thoroughly wipe dry with a soft
absorbent cloth.
Note: The door hinge screw holes have
tolerance, enabling the doors to be adjusted
and centered in the frame.
#20-B
#19
#41
#20-B
#20-C
#20-A
Applying a Polyurethane Coating
Please follow the manufacturer's instruction on the product for application.
11

Seville Classics, Inc.
19401 Harborgate Way Torrance, CA 90501 USA
Telephone: [phone] within USA
Fax: [phone]
Hours: 9:00am - 4:30pm (Pacific Standard Time)
E-mail: sup[email protected]
Website & Online Store: www.sevilleclassics.com
CONTACT INFORMATION
If you are missing any parts, have any questions, or need additional assistance in assembly, please contact our
bilingual (English and Spanish) customer service department at:
***Please visit our website or call and inquire about our additional UltraHD Line***
UltraHD® Line
UltraHD® Tall Storage Cabinet UltraHD® Mega Storage Cabinet
Model No. 16236 (Granite) Model No. 16238 (Granite)
Model No. 20143 (Graphite) Model No. 20148 (Graphite)
Model No. 20153 (Red) Model No. 20158 (Red)
Model No. 20133 (White)
Model No. 20133 (White)
12

UltraHD® 4-Drawer Rolling Cabinet UltraHD® 6-Foot Height Adjustable Workbench
Model No. 20205 (Granite) Model No. 20292 (Granite)
Model No. 20252 (White) Model No. 20293 (Graphite)
Model No. 20258 (Graphite)
UltraHD® Line
UltraHD® Wall Cabinet with Open Shelf UltraHD® 2-Door Rolling Workbench
Model No. 20230 (Granite) Model No. 20262 (Granite)
Model No. 20140 (Graphite) Model No. 20142 (Graphite)
Model No. 20150 (Red) Model No. 20152 (Red)
UltraHD® Rolling Trash Bin
UltraHD® Lighted Workcenter
Model No. 20215 Model No. 20247 (Granite)
Model No. 20246 (Graphite)
Model No. 20157 (Red)
Model No. 20157 (Red)
13