Seville Classics UltraGuard UltraHD 20242 User manual

Reference page 14 for special care and
maintenance of stainless steel
ASSEMBLY INSTRUCTIONS
UltraHD® 12-Drawer Rolling Workbench (Model No. 20242)
77 in. W x 20 in. D x 37.5 in. H
(1.95 m x 50.8 cm x 95.2 cm)
SC200304

Medium -size Drawer
Large Drawer
Small Drawer
12

Small Drawer
Medium-size Drawer
Large Drawer
#12-1
#12-2
#12-5
#15
#13-1
#13-2
#13-4
#15
#26-1
#26-2
#15
3

(#1) LEFT SIDE PANEL x 1 PC
(#2) RIGHT SIDE PANEL x 1PC
(#4) BACK FRAME x 1 PC
(#3) FRONT FRAME x 1 PC
(#7) DOOR x 1 PC
(#8) HARDWOOD TOP x 1 PC
(#5) BASE PANEL x 1 PC
(#6) SHELF x 1 PC
4
PARTS LIST
Please check the parts carefully according to the parts list. If you are missing any parts, please contact
our customer service department (please refer to page 15.)

(#12-2) MEDIUM-SIZE DRAWER BOTTOM PANEL x 3 PCS
(#12-1) MEDIUM-SIZE DRAWER FRONT x 3 PCS
(#13-B) FIXED WHEEL W/O BRAKE x 2 PCS
(#13-1) LARGE DRAWER FRONT PANEL x 1 PC
(#12-5) MEDIUM-SIZE DRAWER BACK PANEL x 3 PCS
(#12-B) SWIVEL WHEEL WITH BRAKE x 2 PCS
(#9) HANDLE BAR x 2 PCS
(#11) MEDIUM-SIZE & LARGE DRAWER SLIDER
SUPPORT x 1 PC
5
PARTS LIST
Please check the parts carefully according to the parts list. If you are missing any parts, please contact
our customer service department (please refer to page 15.)

(#24) DRAWER MAT x 12 PCS
(#25) WRENCH x 1 PC
(#17) SCREW D ( M8 x 18L) x 16 PCS
(#15) SCREW B (M4 x 8L) x 226 PCS
(#21) SCREWDRIVER x 1 PC
(#22) KEY x 2 PCS
(#13-2) LARGE BOTTOM PANEL x 1 PC
(#13-4) LARGE DRAWER BACK PANEL x 1 PC
6
PARTS LIST
Please check the parts carefully according to the parts list. If you are missing any parts, please contact
our customer service department. (please refer to page 15.)

(#26-2) SMALL DRAWER CASE x 8 PCS
(#26-1) SMALL DRAWER FRONT x 8 PCS
(#27) SMALL DRAWER SLIDER SUPPORT x 1 PC
(#27-B) WASHER (M8) x 6 PCS
(#42) SCREW G (M4 x 30L) x 16 PCS
(#57) BUMPER x 4 PCS
(#40) SCREW E (M8 x 18L) x 6 PCS
(#41) SCREW F (M4 x 8L) x 24 PCS
M8X20 pcs
7
PARTS LIST
Please check the parts carefully according to the parts list. If you are missing any parts, please contact
our customer service department. (please refer to page 15.)

TIP:
Step 2.
Note:
Note:
Step 3.
Once the (#1) Left Side Panel is securely
fastened, check to make sure the slider
motion is operating in the correct direction
(Away from the (#4) Back Frame.)
UltraHD® 12-Drawer Rolling Workbench (Model No. 20242)
A magnetic screwdriver is included for your convenience.
If using an electric driver, keep torque setting LOW.
With our customers needs in mind, this package contains
an updated folding drawer construction designed for
faster easier assembly while maintaining a comparable
rigid structure and loading capacity.
Open both boxes and remove the cardboard box
containing the (#8) Hardwood Top.
Place the other parts to the side.
Install Back Frame (#4) to Hardwood Top (#8).
[Use the (#25) Wrench for this step]
Open the cardboard box containing the (#8)
Hardwood Top. Leave the Hardwood Top (#1) on
top of cardboard to reduce the chance of
scratching during assembly.
Locate the (#4) Back Frame. Use (#40) Screw E
and (#27-B) Washers to attach the "Top" of the
(#4) Back Frame as indicated by the attached to
the (#8) Hardwood Board.
(The Hardwood Board has no front or back end.)
Make sure that the rear and both sides of the
back frame are as flush as possible with those of
the Hardwood Top – this may save time by
avoiding having to make slight adjustments later.
You will be assembling the cabinet upside down.
DO NOT fully tighten screws until all the screws
for that part have been partially screwed in.
Install the Left Side Panel (#1).
[Use (#15) Screw B for this step]
Attach (#1) Left Side Panel to (#4) Back Frame,
making sure the "Top" of (#1) Left Side Panel is
on the (#8) Hardwood Top.
Ensure the rear and
side are flush with
Solid Hardwood Top
*NOTE: We recommend using TWO people to assemble the workbench.
8
Step 1.
Note:

Step 4.
Step 5.
Step 7.
Note: The ball bearing track will have to be pulled out about 1" to expose the screw hole used for
fastening to the (#3) Front Frame.
Remove 3 Slides to create the space needed
to use (#21) Screwdriver.
Install the (#11) Medium Size & Large Drawer Slider
Support.
[Use Screw B (#15) & Screwdriver (#21) for this step].
Attach (#11) Medium Size & Large Drawer Slider
Support to the (#4) Back Frame, making sure the "Top"
of Medium Size & Large Drawer Slider Support is close
to the (#8) Hardwood Top. Again, the “Top” is
indicated by a sticker on one of the vertical columns.
Note: the Drawer Slides will face those on the (#1) Left
Side Panel.
Install the (#27) Small Drawer Slider Support.
[Use (#15) Screw B & the (#21) Screwdriver for this
step]. Attach (#27) Small Drawer Slider Support to the
(#4) Back Frame, making sure the "Top" of (#27) Small
Drawer Slider Support is close to the Solid Hardwood
Top. Again, the “Top” is indicated by a sticker on one
of the vertical columns. Note: the Drawer Slide will
face those on the (#2) Right Side Panel also.
Install the (#2) Right Side Panel.
[Use (#15) Screw B for this step]. Please remove 3
Drawer Slides (as shown in picture on the left) before
attaching (#2) Right Side Panel to (#4) Back Frame.
Again, place the "Top" of Side Panel on the Solid
Hardwood Top and attach to Back Frame.
Install the (#3) Front Frame.
[Use (#15) Screw B and (#40) Screw E & (#27-B)
Washer for this step]. Using (#40) Screw E and (#27-B)
Washer, attach the "Top" of the (#3) Front Frame to
the (#8) Hardwood Top. Then, using (#15) Screw B,
attach the (#11) Medium-Size & Large Drawer Slider
Support & (#27) Small Drawer Slider Support and both
(#1 & #2) Left & Right Side Panels to the (#3) Front
Frame.
9
*NOTE: We recommend using TWO people to assemble the workbench.
UltraHD® 12-Drawer Rolling Workbench (Model No. 20242)
Step 6.

Step 11. [Use (#42) Screw G for this step]
Attach (#57) Bumpers to the bottom four corners of Work
Bench. Then, rotate/stand the Work Bench upright.
Step 12. [Use (#41) Screw F for this step]
Attach (#9) Handle Bars on both the (#1 &
#2) Left and Right Side Panels.
[Use (#17) Screw D for this step] Attach (#12-B
& #13-B) Wheels. Make sure that the (#13-B)
Fixed Wheels w/o Brakes are on the same end
(right or left side) of the Workbench.
There is some tolerance in the holes of the
wheel frame, so make sure that the two
wheels w/o brakes are parallel both to each
other and with the frame of the unit.
Step 10. Install (#12-B & #13-B) Wheels.
Step 9. [Use (#15) Screw B for this step]
Attach the (#5) Base Panel to the rest of the unit.
Step 8. Fasten the 3 slides back onto the (#2)
Right Side Panel that you removed in step 6.
10
*NOTE: We recommend using TWO people to assemble the workbench.
UltraHD® 12-Drawer Rolling Workbench (Model No. 20242)

Step 13.
Step 14.
Scan for
Step by
Step Video
Instruction
Note: Do not tighten the screws all the way,
until step 14 is completed.
lnstall (#12-2) Medium-size Drawer Bottom and
(#12-5) Medium-size Drawer Back Panel.
[Use (#15) Screw B for this step].
1. Fold the Left and Right panel up.
2. Attach the back panel to the folded drawer
panel, use 7 pcs (#15) Screw B to tighten.
Install (#12-1) Medium-size Drawer Front.
[Use (#15) Screw B for this step].
From above, slide Left and Right Drawer Panel into
(#12-1) Medium-size Drawer Front as detail picture
shown, use 7 pcs (#15) Screw B to tighten.
Note: The drawer panel should be inserted behind
the folded drawer front edge. The drawer face will
overlap the drawer panel tabs.
Once all the drawer panels are aligned, tighten all
the drawer screws.
Assemble Large Drawer in the same way. Repeat
Step 13 and Step 14, but using
(#13-1) Large Drawer Front Panel, and
(#13-2) Large Drawer Bottom Panel.
#12-1
#15
#12-1
#15
#12-1
#12-2
#12-2
#12-2
#12-5
#15
#13-1
#13-2
#13-4
12-Drawer Rolling Workbench
Assembly on Youtube
11
*NOTE: We recommend using TWO people to assemble the workbench.
UltraHD® 12-Drawer Rolling Workbench (Model No. 20242)

Step 15. Install Small Drawer Front (#26-1) to Small
Drawer Body (#26-2).
1. Fold (#26-2) Small Drawer Body left Panel
and right panel, and back panel up.
3. Slide Left and Right Drawer Panel into (#26-1)
Small Drawer Front as detail picture
shown, use 5pcs (#15) Screw B to tighten.
Once all the drawer panels are aligned, tighten
all the drawer screws.
2. After folding up each panel of (#26-2) Small
Drawer Body, use (#15) Screw B to tighten the
back panel to the Left and right panel.
Note: Do not tighten the screws all the way until
part 3 is completed.
#26-2
#26-2
#15
#26-1
#15
12
*NOTE: We recommend using TWO people to assemble the workbench.
UltraHD® 12-Drawer Rolling Workbench (Model No. 20242)

Step 16.
Note: Pull out the ball bearing
track completely before you
attach drawer.
Place the Drawers.
1. Pull out the sliders completely, then put the
drawer to the sliders, make sure the square
holes on the drawer side panels are line up, and
the drawer is hook on the sliders completely.
2. Use 4 pcs (#15) Screw B to tighten the
drawer, and put (#24) Drawer Mat into the
drawer. Repeat above steps to place other
drawers.
Note: Do not tighten any screws completely
until all the drawers are adjusted well.
Only open one drawer
at a time to avoid
tipping. 40 lbs.
maximum loading for
each drawer.
Hook cutaway view
CAUTION
13
*NOTE: We recommend using TWO people to assemble the workbench.
UltraHD® 12-Drawer Rolling Workbench (Model No. 20242)

Step 17.
Step 18.
UltraHD® Stainless Steel Care Instructions
The stainless-steel parts of this product are protected with an UltraGuard™ fingerprint resistant finish.
DO NOT use traditional stainless-steel cleaners. To safely manage unwanted fingerprints and prevent new stains,
perfom the following steps once monthly:
• Lightly wipe with warm water and clean microfiber cloth
• Always wipe in the direction of the surface grain (NEVER ACROSS)
• Wipe away excess water with dry clean cloth
UltraHD® Wood Top Care Instructions
Our tops are made with real wood, and while great care is taken to ensure consistent top color and graining,
there may be natural variations between finished products. We hand select the wood for every top to ensure
the material is undamaged and naturally beautiful. If the wood top is received with excessive damage or
splitting, Seville Classics will guarantee replacement of the top. Variations of color, and minor scratches in the
clear coat finish will not be reason for replacement.
Restore Shallow Scratches or Chips
The wood surface of this product is finished with a polyurethane coat. If the wood top becomes chipped or
scratched, a polyurethane coat can be reapplied to restore a smooth texture and protect from future damage.
• Please follow the manufacturer's instruction on the product for application.
Install the stainless steel (#7) Door.
[Use (#15) Screw B for this step] Attach
the stainless steel Door (#7) to the unit.
Note that the screw holes on the door
hinge have tolerance, enabling the door to
be adjusted and centered in the door
frame.
Install the (#6) Shelf.
Place the Shelf (#6) in the unit at the
desired height and ensure that all four
corners are secured on the hooks on the
front and back frame.
14
*NOTE: We recommend using TWO people to assemble the workbench.
UltraHD® 12-Drawer Rolling Workbench (Model No. 20242)

,
CONTACT INFORMATION
*If you are missing any parts, have any questions, or need additional assistance in assembly, please contact our bilingual
(English and Spanish) customer service department at:
Seville Classics, Inc.
19401 Harborgate Way Torrance, CA 90501 USA
Telephone: [phone] within USA
Fax: [phone]
Hours: 9:00am - 4:30pm (Pacific Standard Time)
E-mail: [email protected]
Website & Online Store: www.sevilleclassics.com
***Please visit our website or call and inquire about our additional UltraHD Line***
15
UltraHD® Tall Storage Cabinet UltraHD® Mega Rolling Cabinet
Model No. 16236 (Granite)
Model No. 20143 (Graphite)
Model No. 20153 (Red)
Model No. 20133 (White)
Model No. 16238 (Granite)
Model No. 20148 (Graphite)
Model No. 20158 (Red)
UltraHD® Line

UltraHD® Line
UltraHD® Wall Cabinet with Open Shelf
Model No. 20217
UltraHD® Trash Bin
UltraHD® Lighted Workcenter
UltraHD® 2-Door Rolling Workbench
UltraHD® 6-Foot Height Adjustable Workbench
UltraHD® 4-Drawer Rolling Cabinet
Model No. 20205 (Granite)Model No. 20296 (Granite)
Model No. 20141 (Graphite)
Model No. 20230 (Granite)
Model No. 20246 (Graphite)
Model No. 20150 (Red)
Model No. 20262 (Granite)
Model No. 20142 (Graphite)
Model No. 20152 (Red)
Model No. 20247 (Granite)
Model No. 20246 (Graphite)
Model No. 20157 (Red)