Seville Classics UltraHD Ultraguard 20277 User manual

TR161028
ASSEMBLY INSTRUCTIONS
UltraHD® Workcenter
48 in W X 24 in D X 65.5 in H
(1.21 m x 60.9 cm x 1.66 m)
LED work light included
(Model No. 20277)
Reference page 7 for special care and
maintenance of stainless steel

Small Drawer
Top Cantilever Shelf
No. Qty. No. Qty.
#1 1PC #20-5 2PCS
#2-C 1PC #44 1PC
#3-B 1PC #46-1 TOP CANTILEVER SHELF BACK PANEL 1PC
#3-C 1PC #46-2 TOP CANTILEVER SHELF BASE PANEL 1PC
#5-B 2PCS #46-3 TOP CANTILEVER SHELF LEFT PANEL 1PC
#6 4PCS #46-4 TOP CANTILEVER SHELF RIGHT PANEL 1PC
#18 2PCS #47 "L" BRACKET 8PCS
#18-1 TOP CANTILEVER SHELF MAT 1PC #48-1 SMALL DRAWER MIDDLE SUPPORT 1PC
#19-2 DRAWER BASE PANEL 2PCS #48-2 SMALL DRAWER LEFT SUPPORT 1PC
#20-1 SMALL DRAWER FRONT PANEL 2PCS #48-3 SMALL DRAWER RIGHT SUPPORT 1PC
#20-3 SMALL DRAWER LEFT PANEL 2PCS #49 PEGBOARD LONG SUPPORT BAR 2PCS
#20-4 SMALL DRAWER RIGHT PANEL 2PCS
LEVELING FOOT
DRAWER MAT
BOTTOM PEGBOARD PANEL
Parts
Parts
LEG PIECE
PARTS LIST (pg 1 of 8)
Please check the parts carefully according to the parts list. If you are missing any parts, please contact our
customer service department (please refer to page 8 of 8).
STAINLESS STEEL TOP
TOP PEGBOARD PANEL
BOTTOM CROSSBAR
SMALL DRAWER BACK PANEL
LED LAMP

No. Qty. No. Qty.
#15 46PCS #100 4PCS
#21 1PC #101 4PCS
#25 1PC #102 4PCS
#27-B 10PCS #103 4PCS
#40 10PCS #104 2PCS
#41 29PCS #105 2PCS
#45 1PC #106 2PCS
#50 56PCS #107 1PCS
#51 4PCS
SCREW DRIVER
1/2" CURVED
Parts
SCREW F (M4 x 8L)
SCREW E(M8 x 18L)
SCREW I (M6 x 15L)
PARTS LIST (pg 2 of 8)
Please check the parts carefully according to the parts list. If you are missing any parts, please contact our
customer service department (please refer to page 8 of 8).
1" STRAIGHT
1.5" STRAIGHT
WRENCH
WASHER
Parts
SCREW B (M4 x 8L)
1" CURVED
STUD SCREW J
2" DOUBLE PRONG
4" CURVED DOUBLE PRONG
2" PLIER HOLDER
2" MULTI-TOOL HOLDER
POWER STRIP W. USB PORTS
#15
#50
#27-B
#40
#41
#51
#21
#25
#45
#100 #101 #102 #103 #104
#105 #106 #107
M8X20 pcs

Step 1.
Step 2.
NOTE:
Step 3.
NOTE:
ASSEMBLY INSTRUCTIONS (pg 3 of 8)
*NOTE: We recommend TWO people to assemble the workbench.
Install (#5-B) Leg Piece.
A: Open the package, and put the parts aside. Then, attach the (#47) "L" Bracket to the (#5-B) Leg Piece, use (#50)
Screw I to tighten. Repeat Step A to install (#47) "L" Brackets to another one (#5-B) Leg Piece.
Note: Tighten the all the screws after the (#47) Brackets are flush with the (#5-B) Leg Piece.
Install (#3-B) Bottom Cross Bar and (#6) Leveling Feet.
Attach the (#3-B) Bottom Cross Bar to the back of (#5-B)
Leg Piece, line up the screw holes, use (#40) Screw E with
(#27-B) Washer and (#25) Wrench to tighten.
After installing (#5-B) Leg Pieces, attach (#6) Leveling Feet
to (#5-B) Leg Pieces, use (#25) Wrench to tighten.
TIP: A magnetic screwdriver is included for your convenience. If a power screwdriver is used, keep on a low torque
setting.
Upturn the workbench once you finish this step.
Do not fully tighten the screws. This will help you make
any adjustments for alignment.
B: Attach the (#5-B) Leg Pieces to the back of the (#1) Stainless Steel Top, line up the screw holes, use (#50) Screw I and
(#21) Screwdriver to tighten.
Note: Assemble the workcenter on top of the cardboard packaging to help avoid scratching the stainless steel top.
Install (#48-1) Small Drawer Middle Support, (#48-2)
Small Drawer Left Support, (#48-3) Small Drawer Right
Support.
Attach the (#48-1) Small Drawer Middle Support to the
back of (#1) Stainless Steel Top Back, line up the screw
holes, use (#50) Screw I and (#21) Screwdriver to tighten.
Repeat this step to install (#48-2) Small Drawer Left
Support and (#48-3) Small Drawer Right Support.
A
B
Back

Step 4.
Step 5.
Step 6. Install (#46) Top Cantilever Shelf .
Step 7.
Install Assembled (#46) Top Cantilever Shelf to
workbench.
Attach assembled (#46) Top Cantilever Shelf to (#2-C) Top
Pegboard Panel and (#49) Pegboard Long Support Bars, line up
the screw holes, use (#41) Screw F to tighten. Use (#15) Screw B
to fasten the (#2-C) Top Pegboard and (#46) Top cantilever Shelf.
NOTE: Do not fully tighten the screws. This will help you make
any adjustments for alignment later.
ASSEMBLY INSTRUCTIONS (pg 4 of 8)
*NOTE: We recommend TWO people to assemble the workbench.
A). Attach the (#46-3) Top Cantilever Shelf Left Panel and the
(#46-4) Top Cantilever Shelf Right Panel to (#46-2) Top Cantilever
Shelf Base Panel. Use (#41) F screws to tighten.
NOTE: Do not fully tighten the screws. This will help you make
any adjustments for alignment later.
B). Make sure to slide the back panel underneath the edge of
(#46-2) Top Cantilever Shelf Base Panel. Use (#41) F screws to
tighten.
Install (#49) Pegboard Long Support Bar.
Attach (#49) Pegboard Long Support Bar to the back of the
workbench, line up the screw holes, use (#40) Screw E with (#27-
B) Washer to tighten.
NOTE: Do not fully tighten the screws. This will help you make
any adjustments to alignment later.
Install (#3-C) Bottom Pegboard Panel and (#2-C) Top
Pegboard Panel.
Attach (#3-C) Bottom Pegboard Panel along the back top edge of
workbench and against (#49) Pegboard Long Support Bar, line
up the screw holes, use (#41) Screw F and (#21) Screwdriver to
tighten. Use (#15) Screw B to fasten the (#2-C) & (#3-C) Top &
Bottom Pegboard.
NOTE: Do not fully tighten the screws. This will help you make
any adjustments to alignment later.
Attach (#2-C) Top Pegboard Panel to the top of (#3-C) Bottom
Pegboard Panel and (#49) Pegboard Long Support Bar, line up
the screw holes, use (#41) Screw F and (#21) Screwdriver to
tighten.
A
B