Seville Classics UltraHD 20108 User manual

ASSEMBLY INSTRUCTIONS
UltraHD Rolling Workbench Cabinet (Model No. 20108)
(48" W X 20" D X 37.5" H)

(pg 1 of 14)

(pg 2 of 14)
(#12)Small Drawer Assembly
(#13)Large Drawer Assembly

PARTS LIST (pg 3 of 14)
(#1) LEFT PANEL x 1 PC
(#2) RIGHT PANEL x 1 PC
Please check the parts carefully according to the parts list. If you are missing any parts, please
contact our customer service department .
(#4) BACK FRAME x 1 PC
(#3) FRONT FRAME x 1 PC
(#7) DOOR x 1 PC
(#8) SOLIDE HARDWOOD BOARD x 1 PC
(#5) BASE PANEL x 1 PC
(#6) SHELF x 1 PC

(#12-1) MEDIUM-SIZE DRAWER FRONT x 3 PCS
(#11) RIGHT DRAWER SLIDE SUPPORT x 1 PC
(#13-1) LARGE DRAWER FRONT PANEL x 1 PC
(#13-2) LARGE DRAWER BOTTOM PANEL x 1 PC
(#12-2) MEDIUM-SIZE DRAWER BOTTOM PANEL x 3 PCS
(#12-5) SMALL DRAWER BACK PANEL x 3 PCS
PARTS LIST (pg 4 of 14)
(#9) PUSH BAR x 2 PCS
(#10) BUMPER x 4 PCS
Please check the parts carefully according to the parts list. If you are missing any parts, please
contact our customer service department .

(#30) SIDE PANEL LOGO TRIM x 1PC
(#27-B) WASHER (M8) x 4 PCS
(#40) SCREW E (M8 x 18L) x 4PCS
(#45) USB MULTIPLE SOCKET-OUTLET x 1PC
(#15) SCREW B ( M4 x 8L) x 84 PCS
(#29) CASTER SEAT SUSHION x 4PCS
PARTS LIST (pg 5 of 14)
(#13-4) LARGE DRAWER BACK PANEL x 1 PC
(#28) SOCKET FIXED SEAT x 2PCS
Please check the parts carefully according to the parts list. If you are missing any parts, please
contact our customer service department .
M8X20 pcs

(#65) SCREW P (M8 x 30L) x 16 PCS
(#20) SWIVEL WHEEL WITH BRAKE x 2 PCS
(#21) FIXED WHEEL W/O BRAKE x 2 PCS
(#26) SCREW DRIVER x 1 PC
(#22) DOOR KEY x 4PCS
(#23) Magnet x 2 PCS
(#41) SCREW F (M4 x 8L) x 65 PCS
(#42) SCREW G (M4 x 30L) x 16 PCS
PARTS LIST (pg 6 of 14)
Please check the parts carefully according to the parts list. If you are missing any parts, please
contact our customer service department .

PARTS LIST (pg 7 of 14)
(#24) DRAWER MAT x 4PCS
(#25) WRENCH x 1 PC
contact our customer service department .
Please check the parts carefully according to the parts list. If you are missing any parts, please

(pg 8 of 14)
Install (#30)side panel logo trim and (#45)USB multiple socket-outlet
UltraHD Rolling Workbench Cabinet (Model No. 20108)
1.Attach (#45) USB multiple socket-outlet on side panel, which can be assembled on
(#1) left side panel or (#2) right side panel according to user demand .
2.Attach multiple socket-outlet on side panel, use 2pcs (#28) socket fixed seat and
4pcs (#41) screws F to Install, put multiple socket-outlet cable into the wire slot of
side panel, as show picture B.
3.Install (#30)side panel logo trim ,as show picture A,use 4pcs (#41) screws F to
tighten on side panel.
A
B

Step 1.
Note:
Step 2.
Step 3.
UltraHD Rolling Workbench Cabinet (Model No. 20108)
(pg 9 of 14)
Install Back Frame(#4)
Open the package, remove (#8) solide hardwood board
and (#4) back frame ; put (#4) back frame onto (#8)
solide hardwood board as show on left picture, take out
2pcs (#27-B) washer and 2pcs (#40) screws E ,then
use wrench (#25) to tighten on solide hardwood board.
Step 1~Step 5, don't tighten screws completely.
Attach (#2) right side panel on solide hardwood board
as show, use 3pcs (#41) screw F to tighten on back
frame.
Install (#2) right side panel.
Attach (#11) right drawer slide support on solide
hardwood board as show , pay attention to direction in
which slide rail is pulled out ,use 4pcs (#15) screw B to
tighten on back frame.
Install (#11) right drawer slide support

Step 4.
Step 5.
Note:
Step 6.
Install Base Panel (#5)
Attach Base Panel (#5) on right drawer slide
support as show left picture, use 12pcs (#41)
screw F to tighten on the left side panel, right side
panel, back frame and front frame.
UltraHD Rolling Workbench Cabinet (Model No. 20108)
(pg 10 of 14)
Repeat step 2, attach Left Side Panel (#1) on solide
hardwood board, use 3pcs (#41) screw F to
tighten on back frame.
Install Left Side Panel (#1)
Install Front Frame(#3)
Attach front frame (#3) on solide hardwood board
as show, use 6pcs (#41) screw F to tighten on left
and right side panels, and use 4pcs (#15) screw B
to tighten on right drawer slide support . use 2pcs
(#27-B) washer and 2pcs (#40) screw E to tighten
on solide hardwood board.
Tighten all screws completely. The edges of all
accessories are aligned when tightening screws.

Step 7.
Note:
Step 8.
Note:
Step 9. Step 10.
UltraHD Rolling Workbench Cabinet (Model No. 20108)
(pg 11 of 14)
Install (#29) caster seat sushion and Wheels (#20
& #21)
Attach 4pcs (#29) caster seat sushion and 4pcs wheels
(#20)&(#21) on the frame as shown in left picture, use the
16pcs (#65) screws P to tighten them. Make sure that the
(#21)Fixed wheels w/o Brakes are on the same end (right
or left side) of the Work Bench. Also the (#20) Swivel
wheel with brake.
The opening direction of caster seat sushion need to
upward wheels, as shown by the arrow on the left.
Install Bumpers (#10)
Install 4pcs (#10) Bumpers on four corners of the cabinet
as show on left, use 16pcs (#42) screws G with
screwdriver to tighten them.
Install (#23) Magnet
Install 2pcs (#23) Magnet on right side of the
center column of the front frame as show on
above, use 4pcs (#41) screw F to tighten it.
When install bumpers , the screw only needs to be
tightened to a little bit recessed than the rubber corner
protector surface, please remember not to lock it too
tightly.
Install (#9) handle bar.
Install 2pcs (#9) handle bar on both sides of the
cabinet as show on above, use 24pcs (#41)
screws F to tighten them.

Step 11.
Step 12.
Step 13.
Install (#12-2) Medium-Size drawer base on
middle drawer panel (#12-1)from up to
down as show on left, use 7PCS (#15)
screws to tighten it.
Repeat above steps ,assemble the other 2pcs
middle drawer (#12).
Install Large Drawer (#13)
Refer step 11.12, take out large drawer front
panel (#13-1), large drawer base (#13-2),
large drawer back panel (#13-4) ,then use
18pcs (#15) screws B to tighten them.
UltraHD Rolling Workbench Cabinet (Model No. 20108)
(pg 12 of 14)
1. Fold left and right sides of (#12-2)
Medium-Size drawer base firstly as show on
left;
2. Then install (#12-5)small drawer back
panel to Medium-Size drawer base as show,
use 7pcs (#15) screws B to tighten it.
Install (#12-2) Medium-Size Drawer Base
and (#12-5) Small Drawer Back Panel.
Install MEDIUM-SIZE DRAWER FRONT(#12-
1)

Step 14.
Note:
As show picture C, the height gap of the drawer can be
adjusted by OB holes which in the front of the slide rail .
C
Place the Drawers
B
3. Repeat step 14, install the other 3pcs middle drawers
(#12).
4. Put 1pcs (#24) Drawer mat into each drawer.
After all drawers are installed, the gap between the drawers
is uneven, you can loosen the screws on the inner rail and
adjust the drawer up and down.
UltraHD Rolling Workbench Cabinet (Model No. 20108)
(pg 13 of 14)
1). Pull out the sliders completely, then put the
drawer to the sliders, make sure the square holes
on the drawer side panels are line up, and the
drawer is hook on the sliders completely as show left.
2). Use 4pcs (#15) Screw B to tigthen on drawer
slides.
A
#12
#12

Step 15.
Note:
Step 16.
Note:
Finished.
UltraHD Rolling Workbench Cabinet (Model No. 20108)
(pg 14 of 14)
Install Door panel (#7)
Attach the door panel (#7) on front frame ,
use 5pcs (#41) screws F tighten.
The OB holes on the door hinge have
tolerance, enabling the door to be adjusted
and centered in the door frame.
Install Shelf (#6)
Place Shelf (#6) in unit at the desired height
and ensure that all four corners are secured
on the hooks in the front and back.
The height of the shelf can be adjusted
according to the hook in the cabinet.