SEW-Eurodrive MOVIMOT MM07 User manual

Gearmotors \ Industrial Gear Units \ Drive Electronics \ Drive Automation \ Services
MOVIMOT
®
for Energy Efficient Motors
O perating I nstructions
Edition 05/2007
11641819 / EN

SEW-EURODRIVE – Driving the world

Addendum to the Operating Instructions – MOVIMOT® for Energy Efficient Motors 3
1
Structure of the safety notes
General notes
Addendum to the Operating Instructions
1 General notes
1.1 Structure of the safety notes
The safety notes in these operating instructions are designed as follows:
1.2 Right to claim under warranty
A requirement of fault-free operation and fulfillment of any rights to claim under limited
warranty is that you adhere to the information in the MOVIMOT®documentation. Con-
sequently, read the operating instructions before you start working with the unit!
Make sure that the operating instructions are available to persons responsible for the
plant and its operation, as well as to person who work independently on the unit. You
must also ensure that the documentation is legible.
1.3 Exclusion of liability
You must comply with the information contained in the MOVIMOT®documentation to
ensure safe operation of MOVIMOT®and to achieve the specified product characteris-
tics and performance requirements. SEW-EURODRIVE assumes no liability for injury to
persons or damage to equipment or property resulting from non-observance of these
operating instructions. In such cases, any liability for defects is excluded.
Pictogram SIGNAL WORD!
Type and source of danger.
Possible consequence(s) if the safety notes are disregarded.
• Measure(s) to prevent the danger.
Pictogram Signal word Meaning Consequences in case of
disregard
Example:
General danger
Specific danger,
e.g. electric shock
DANGER! Imminent danger Severe or fatal injuries
WARNING! Possible dangerous situation Severe or fatal injuries
CAUTION! Possible dangerous situation Minor injuries
STOP! Possible damage to property Damage to the drive system or its environ-
ment
NOTE Useful information or a tip
Simplifies the handling of the
drive system

4Addendum to the Operating Instructions – MOVIMOT® for Energy Efficient Motors
1Other applicable documentation
General notes
1.4 Other applicable documentation
• This information does not replace the detailed operating instructions!
• Only electrical specialists are allowed to perform installation and startup observing
applicable accident prevention regulations and the "MOVIMOT®MM..C" operating
instructions.

Addendum to the Operating Instructions – MOVIMOT® for Energy Efficient Motors 5
2
Changes compared to the standard MOVIMOT® MM..C
Description of functions
2 Description of functions
2.1 Changes compared to the standard MOVIMOT®MM..C
• This design is exclusively intended for operation with energy efficient DTE/DVE or
DRE motors (230 V/400 V m/W).
These energy efficient motors meet the requirements of efficiency category .
• Modified MOVIMOT®combinations, see page 6.
• Modified DIP switch setting (S2/1), see page 9.
2.2 Sample unit designation
Inverter name-
plate (example)
MM 15 C – 503 – 05
Type 05 for DTE/DVE motors
for DRE motors (as of firmware status 71)
Connection type (3 = 3-phase)
Connection voltage (50 = 380...500 VAC)
Version C
Motor power (15 = 1.5 kW)
MOVIMOT®series
62024AXX
[1] Firmware status
71 54 C 52 50 -- 10 10 10
MM15C-503-05
71
[1]
1820 462 7

6Addendum to the Operating Instructions – MOVIMOT® for Energy Efficient Motors
3MOVIMOT® combinations with energy efficient motors
Changes compared to the standard MOVIMOT®
3 Changes compared to the standard MOVIMOT®
3.1 MOVIMOT®combinations with energy efficient motors
MOVIMOT®with energy efficient DTE/DVE motors
280 – 1400 1/min W 3 x 380 – 500 V (400 V) IEC design
290 – 2900 1/min m 3 x 380 – 500 V (400 V) IEC design
STOP!
All combinations not listed in this document will be rejected with error 9 (slowly flashing
red status LED on MOVIMOT®).
57770AXX
Type PNMnMa/MnnnIn1 cosϕBrake MBmax
[kW] [Nm] [Nm] [1/min] [A] Preference Alternative [Nm]
DTE90K4/.../MM07 0.75 5.1 1.5 1400 1.8 0.99
BMG2
230 V
BMG2
400 V
20
DTE90S4/.../MM11 1.1 7.5 1.5 1400 2.4 0.99 20
DTE90L4/.../MM15 1.5 10.2 1.5 1400 3.2 0.99 20
DVE100M4/.../MM22 2.2 15.0 1.5 1400 4.6 0.99 BMG4
110 V
BMG4
230 V
40
DVE100L4/.../MM30 3.0 20.5 1.5 1400 6.2 0.99 40
Type PNMnMa/MnnnIn1 cosϕBrake MBmax
[kW] [Nm] [Nm] [1/min] [A] Preference Alternative [Nm]
DTE90K4/.../MM11 1.1 3.62 2.0 2900 3.1 0.99 BMG2
230 V
BMG2
400 V
20
DTE90S4/.../MM15 1.5 4.95 1.6 2900 4.2 0.99 20
DTE90L4/.../MM22 2.2 7.25 1.6 2900 5.5 0.99 BMG2
110 V
BMG2
230 V 20
DVE100M4/.../MM30 3.0 9.9 1.6 2900 8.0 0.99
BMG4
110 V
BMG4
230 V
40
DVE100L4/.../MM3X 3.0 1)
1) S1
9.9 1.6 2900 8.0 0.99 40
4.0 2)
2) S3, 25 % c.d.f.
13.2 1.2 2900 10.7 0.99
Thermal classification F as standard
MM07 - MM15 MM22 - MM3X

Addendum to the Operating Instructions – MOVIMOT® for Energy Efficient Motors 7
3
MOVIMOT® combinations with energy efficient motors
Changes compared to the standard MOVIMOT®
MOVIMOT®with energy efficient DTE/DVE motors and increased short-term torque
280 – 1400 1/min W 3 x 380 – 500 V (400 V) IEC design
290 – 2900 1/min m 3 x 380 – 500 V (400 V) IEC design
57771AXX
MM11 - MM15 MM22 - MM3X
Type PNMnMa/Mn1) nnIn1 cosϕBrake MBmax
[kW] [Nm] [Nm] [1/min] [A] Preference Alternative [Nm]
DTE90K4/.../MM11 0.75 5.1 2.1 1400 1.8 0.99 BMG2
230 V
BMG2
400 V
20
DTE90S4/.../MM15 1.1 7.5 2.1 1400 2.4 0.99 20
DTE90L4/.../MM22 1.5 10.2 2.1 1400 3.2 0.99 BMG2
110 V
BMG2
230 V 20
DVE100M4/.../MM30 2.2 15.0 2.1 1400 4.6 0.99 BMG4
110 V
BMG4
230 V
40
DVE100L4/.../MM3X 3.0 20.5 2.0 1400 6.2 0.99 40
Type PNMnMa/Mn1)
1) Increased short-term torque in S3 operation, 25 % cdf
nnIn1 cosϕBrake MBmax
[kW] [Nm] [Nm] [1/min] [A] Preference Alternative [Nm]
DTE90K4/.../MM15 1.1 3.62 2.5 2900 3.1 0.99 BMG2
230 V
BMG2
400 V 20
DTE90S4/.../MM22 1.5 4.95 2.2 2900 4.2 0.99 BMG2
110 V
BMG2
230 V
20
DTE90L4/.../MM30 2.2 7.25 2.2 2900 5.0 0.99 20
DVE100M4/.../MM3X 3.0 9.9 2.0 2900 8.0 0.99 BMG4
110 V
BMG4
230 V 40
Thermal classification F as standard

8Addendum to the Operating Instructions – MOVIMOT® for Energy Efficient Motors
3MOVIMOT® combinations with energy efficient motors
Changes compared to the standard MOVIMOT®
MOVIMOT®with energy efficient DRE motors
280 – 1400 1/min W 3 x 380 – 500 V (400 V) IEC design
290 – 2900 1/min m 3 x 380 – 500 V (400 V) IEC design
62083AXX
MM07 - MM15 MM22 - MM30
Type PNMnMa/MnnnIn1 cosϕBrake MBmax
[kW] [Nm] [Nm] [1/min] [A] [Nm]
DRE80M4/.../MM07 0.75 5.1 1.5 1400 1.8 0.99 BE1
230 V
10
DRE90M4/.../MM11 1.1 7.5 1.5 1400 2.4 0.99 BE2
230 V
20
DRE90L4/.../MM15 1.5 10.2 1.5 1400 3.2 0.99 20
DRE100M4/.../MM22 2.2 15.0 1.5 1400 4.6 0.99 BE5
120 V
50
DRE100LC4/.../MM30 3.0 20.5 1.5 1400 6.2 0.99 50
Type PNMnMa/MnnnIn1 cosϕBrake MBmax
[kW] [Nm] [Nm] [1/min] [A] [Nm]
DRE80M4/.../MM11 1.1 3.62 2.0 2900 3.1 0.99 BE1
230 V 10
DRE90M4/.../MM15 1.5 4.95 1.6 2900 4.2 0.99 BE2
230 V 20
DRE90L4/.../MM22 2.2 7.25 1.6 2900 5.5 0.99 BE2
120 V 20
DRE100M4/.../MM30 3.0 9.9 1.6 2900 8.0 0.99 BE5
120 V 50
Thermal classification F as standard

Addendum to the Operating Instructions – MOVIMOT® for Energy Efficient Motors 9
3
Modified DIP switch setting
Changes compared to the standard MOVIMOT®
3.2 Modified DIP switch setting
The firmware status 70 only supports energy efficient DTE/DVE motors.
The DIP switch S2/1 can be set to ON or OFF.
As of firmware status 71, energy efficient DTE/DVE and DRE motors are supported.
• If the energy efficient DTE/DVE motors are used, the DIP switch S2/1 must be set to
OFF.
• If the energy efficient DRE motors are used, the DIP switch S2/1 must be set to ON.
DIP SWITCH S1:
DIP SWITCH S2:
S1 1 2 3 4 5
Motor
protec-
tion
6
Motor power rat-
ing
7
PWM fre-
quency
8
No-load
damping
Meaning RS485 address
20212223
ON 1111 Off Motor one stage
smaller
Variable
(16, 8, 4 kHz) On
OFF 0 0 0 0 On Adjusted 4 kHz Off
S2 1 2 3 4 5 6 7 8
Meaning Motor type Brake released
without enable
Control
mode
Speed moni-
toring
Additional func-
tions
20212223
ON DRE-1)
Motor
1) only possible as of firmware status 71
On U/f On 1111
OFF DTE/DVE
motor Off VFC Off 0000