SEW-Eurodrive MOVI-SWITCH-1E Administrator guide

Drive Technology \ Drive Automation \ System Integration \ Services
Compact Operating Instructions
MOVI-SWITCH
®
1E/2S
Edition 03/2010 16722426 / EN

SEW-EURODRIVE—Driving the world

Compact Operating Instructions – MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE/DRP 3
Contents
Contents
1 General Information ............................................................................................ 4
1.1 Scope of this documentation....................................................................... 4
1.2 Structure of the safety notes ....................................................................... 4
2 Safety Notes ........................................................................................................ 5
2.1 General ....................................................................................................... 5
2.2 Target group ............................................................................................... 5
2.3 Designated use ........................................................................................... 5
2.4 Other applicable documentation ................................................................. 6
2.5 Transportation, storage............................................................................... 6
2.6 Installation................................................................................................... 6
2.7 Electrical Connection .................................................................................. 7
2.8 Safe disconnection...................................................................................... 7
2.9 Operation .................................................................................................... 7
3 Type Designation ................................................................................................ 8
3.1 Nameplate, unit designation of MOVI-SWITCH®-1E (example) ................. 8
3.2 Nameplate, type designation MOVI-SWITCH®-2S ..................................... 9
4 Mechanical Installation (all MOVI-SWITCH®variants) ................................... 11
4.1 Installation instructions.............................................................................. 11
4.2 Mounting MOVI-SWITCH®with option P22A close to the motor .............. 12
4.3 Tightening torques .................................................................................... 13
5 Electrical Installation ........................................................................................ 15
5.1 Installation instructions.............................................................................. 15
5.2 MOVI-SWITCH®-1E.................................................................................. 18
5.3 MOVI-SWITCH®-2S/CB0 (binary control)................................................. 20
5.4 MOVI-SWITCH®-2S/CK0 (control with AS-Interface) ............................... 27
6 Startup................................................................................................................ 33
6.1 Startup notes (all MOVI-SWITCH®variants) ............................................ 33
6.2 Starting up MOVI-SWITCH®-1E ............................................................... 33
6.3 Starting up MOVI-SWITCH®-2S/CB0 (binary control) .............................. 34
6.4 Starting up MOVI-SWITCH®-2S/CK0 (control via AS-Interface)............... 36
7 Operation ........................................................................................................... 38
7.1 Operating display (binary control) ............................................................. 38
7.2 Operating display (control via AS-Interface) ............................................. 40
8 Service ............................................................................................................... 42
8.1 MOVI-SWITCH®-1E.................................................................................. 42
8.2 MOVI-SWITCH®-2S.................................................................................. 42
9 Declaration of Conformity ................................................................................ 43

4Compact Operating Instructions – MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE/DRP
1Scope of this documentation
General Information
MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE /DRP
1 General Information
1.1 Scope of this documentation
This documentation comprises the general safety notes and a selected information
regarding MOVI-SWITCH®-1E/-2S.
• Please note that this documentation does not replace the detailed operating
instructions.
• Read the detailed operating instructions first before you start working with
MOVI-SWITCH®-1E/-2S.
• Observe the information, instructions and notes in the detailed operating instructions.
Doing so is a prerequisite for trouble-free operation of MOVI-SWITCH®-1E/-2S and
fulfillment of any rights to claim under guarantee.
• The enclosed CD or DVD contains PDF files of the additional operating instructions
as well as further MOVI-SWITCH®-1E/-2S documentation.
• All SEW-EURODRIVE’s technical documentation is available for download in PDF
format from the SEW-EURODRIVE website: www.sew-eurodrive.de.
1.2 Structure of the safety notes
The safety notes in these operating instructions are designed as follows:
Pictogram SIGNAL WORD
Type and source of danger.
Possible consequence(s) if disregarded.
• Measure(s) to prevent the danger.
Pictogram Signal word Meaning Consequences if disre-
garded
Example:
General danger
Specific danger,
e.g. electric shock
DANGER Imminent danger Severe or fatal injuries
WARNING Possible dangerous situation Severe or fatal injuries
CAUTION Possible dangerous situation Minor injuries
NOTICE Possible damage to property Damage to the drive system or its environ-
ment
INFORMA-
TION
Useful information or tip.
Simplifies the handling of the
drive system.

Compact Operating Instructions – MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE/DRP 5
2
General
Safety Notes
2 Safety Notes
The following basic safety notes are intended to prevent injury to persons and damage
to property. The operator must ensure that the basic safety notes are read and
observed. Make sure that persons responsible for the system and its operation, as well
as persons who work independently on the unit, have read through the operating
instructions carefully and understood them. If you are unclear about any of the
information in this documentation, please contact SEW-EURODRIVE.
2.1 General
Never install or start up damaged products. Submit a complaint to the shipping company
immediately in the event of damage.
During operation, MOVI-SWITCH®drives can have live, bare and movable or rotating
parts as well as hot surfaces, depending on their enclosure.
Removing covers without authorization, improper use as well as incorrect installation or
operation may result in severe injuries to persons or damage to property. Refer to the
documentation for additional information.
2.2 Target group
Only qualified personnel is authorized to install, startup or service the units or correct
unit faults (observing IEC 60364 or CENELEC HD 384 or DIN VDE 0100 and IEC 60664
or DIN VDE 0110 as well as national accident prevention guidelines).
Qualified personnel in the context of these basic safety notes are persons familiar with
installation, assembly, startup and operation of the product who possess the necessary
qualifications.
Any activities regarding transportation, storage, operation, and disposal must be carried
out by persons who have been instructed appropriately.
2.3 Designated use
• MOVI-SWITCH®drives are intended for industrial systems. They comply with the
applicable standards and regulations and meet the requirements of the Low Voltage
Directive 2006/95/EC.
• Technical data and information on approved conditions on site can be found on the
nameplate and in the "MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE/DRP"
operating instructions.
• You must comply with this information!
• Do not start up the unit (operate in the designated fashion) until you have established
that the machine complies with the EMC Directive 2004/108/EC and that the end
product conforms to Machinery Directive 2006/42/EC (with reference to EN 60204).

6Compact Operating Instructions – MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE/DRP
2Other applicable documentation
Safety Notes
2.3.1 Safety functions
The MOVI-SWITCH®drives may not perform safety functions unless these functions are
described and expressly permitted.
2.3.2 Hoist applications
MOVI-SWITCH®drives are suitable for hoist applications to a limited degree only.
MOVI-SWITCH®drives must not be used as safety devices in hoist applications.
2.4 Other applicable documentation
Note also the following documentation:
• "AC Motors DRS/DRE/DRP" operating instructions
• "Fieldbus Interfaces/Field Distributors for Controlling MOVI-SWITCH®" manual
2.5 Transportation, storage
You must observe the notes on transportation, storage and proper handling. Comply
with the requirements for climatic conditions stated in chapter "Technical Data" of the
operating instructions. Tighten installed eyebolts securely. They are designed for the
weight of the MOVI-SWITCH®drive. Do not attach any additional loads. Use suitable,
sufficiently rated handling equipment (e.g. rope guides) if required.
2.6 Installation
The units must be installed and cooled according to the regulations and specifications
in the corresponding documentation.
Protect the MOVI-SWITCH®drives from excessive strain.
The following applications are prohibited unless explicitly permitted:
• Use in potentially explosive atmospheres.
• Use in areas exposed to harmful oils, acids, gases, vapors, dust, radiation, etc.
• Use in non-stationary applications with strong mechanical oscillation and impact
loads, see the "Technial Data" chapter in the "MOVI-SWITCH®-1E/-2S with
AC Motor DRS/DRE/DRP" operating instructions.

Compact Operating Instructions – MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE/DRP 7
2
Electrical Connection
Safety Notes
2.7 Electrical Connection
Observe the applicable national accident prevention guidelines when working on live
MOVI-SWITCH®drives (e.g. BGV A3).
Perform electrical installation according to the pertinent regulations (e.g. cable cross
sections, fusing, protective conductor connection). Additional information is contained in
the documentation.
The manufacturer of the system or machine is responsible for maintaining the limits
established by EMC legislation.
Protective measures and protection devices must comply with the regulations in force
(e.g. EN 60204 or EN 61800-5-1).
2.8 Safe disconnection
MOVI-SWITCH®drives meet all requirements for safe disconnection of power and
electronic connections in accordance with EN 61800-5-1. All connected circuits must
also satisfy the requirements for safe disconnection.
2.9 Operation
Systems with integrated MOVI-SWITCH®drives must be equipped with additional
monitoring and protection devices according to the applicable safety guidelines, such as
the law governing technical equipment, accident prevention regulations, etc. Additional
protective measures may be necessary for applications with increased potential risk.
Before removing the terminal box cover/MOVI-SWITCH®control unit, disconnect the
MOVI-SWITCH®drive from the supply system.
The terminal box must remain closed during operation, i.e. the terminal box cover and
theMOVI-SWITCH®control unit must be screwed on.
Mechanical blocking or internal safety functions of the unit can cause a motor standstill.
Eliminating the cause of the problem or performing a reset may result in the drive re-
starting automatically. If, for safety reasons, this is not permitted for the driven machine,
disconnect the unit from the supply system before correcting the error.
Caution: Danger of burns: The surface temperature of MOVI-SWITCH®can exceed
60 °C during operation!

8Compact Operating Instructions – MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE/DRP
3Nameplate, unit designation of MOVI-SWITCH®-1E (example)
Type Designation
3 Type Designation
3.1 Nameplate, unit designation of MOVI-SWITCH®-1E (example)
1020396043
R 27 DRS 71S4 /BE05/TF/Z/MSW/ASA3/AVS1
M12 connector for control signals
Plug connector option
MOVI-SWITCH®
Motor option heavy fan
Temperature sensor
(standard)
Motor option: brake
Motor size and number of poles
Motor series
Gear unit size
Gear unit series

Compact Operating Instructions – MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE/DRP 9
3
Nameplate, type designation MOVI-SWITCH®-2S
Type Designation
3.2 Nameplate, type designation MOVI-SWITCH®-2S
3.2.1 Sample motor nameplate
1021652363
R 27 DRS 71S4 /BE05/TF/Z/MSW/CB0/ASA3
Plug connector option
Variant: 0 = Standard
Signal type:
B = Binary
K = AS-Interface
Control
MOVI-SWITCH®
Motor option heavy fan
Temperature sensor
(standard)
Motor option: brake
Motor size and number of poles
Motor series
Gear unit size
Gear unit series

10 Compact Operating Instructions – MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE/DRP
3Nameplate, type designation MOVI-SWITCH®-2S
Type Designation
3.2.2 Sample electronics nameplate
3.2.3 "Mounting close to the motor" type with option P22A
The following illustration shows an example of MOVI-SWITCH®2S installed close to the
motor with the corresponding nameplate and type designation:
1022004363
MSW CB0
Variant: 0 = Standard
Signal type:
B = Binary, K = AS-Interface
Control
MOVI-SWITCH®
1068243467
MSW-2S-07A/CB0/P22A/RI2A/ALA4
Plug connector for the connection to the motor
Terminal box design
Adapter for mounting MOVI-SWITCH®close to the
motor
Variant: 0 = Standard
Signal type:
B = Binary, K = AS-Interface
Control
MOVI-SWITCH®

Compact Operating Instructions – MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE/DRP 11
4
Installation instructions
Mechanical Installation (all MOVI-SWITCH®variants)
4 Mechanical Installation (all MOVI-SWITCH®variants)
4.1 Installation instructions
4.1.1 Before you start
The MOVI-SWITCH®drive may only be installed if:
• The entries on the nameplate of the drive match the voltage supply system.
• The drive is undamaged (no damage caused by transportation or storage).
• You have ensured that there are no oils, acids, gases, vapors, radiation, etc. present
Installation
tolerances
4.1.2 Mounting the MOVI-SWITCH®drive
Observe the following mounting instructions:
• Install/mount MOVI-SWITCH®only in the specified mounting position on a level,
vibration-free, and torsionally rigid support structure.
• Clean the output shafts thoroughly to ensure they are free of anti-corrosion agents
(use a commercially available solvent). Do not expose the bearings and sealing rings
to the solvent – damage to the material!
• Carefully align MOVI-SWITCH®and the driven machine to avoid placing any
unacceptable strain on motor shafts (observe permitted overhung and axial loads).
• Do not butt or hammer the shaft end.
• Use an appropriate cover to prevent objects or fluids from entering in vertical
mounting positions.
• Ensure there is sufficient clearance around the unit to allow for adequate cooling.
Furthermore, the unit must be positioned in such a way that it does not reuse the air
warmed by other devices.
• Balance components for subsequent mounting on the shaft with a half key (output
shafts are balanced with a half key). Any condensation drain holes are closed with
plastic plugs and must not be opened unless needed.
• Open condensation drain holes are not permitted. They would render the assigned
degrees of protection void.
Shaft end Flanges
Diameter tolerance according to EN 50347
• ISO j6 with Ø ≤26 mm
• ISO k6 with Ø ≤38 mm up to ≤48 mm
• ISO m6 at Ø > 55 mm
• Center bore in accordance with DIN 332,
shape DR..
Centering shoulder tolerance in accordance
with EN 50347
• ISO j6 with Ø ≤250 mm
• ISO h6 with Ø > 300 mm

12 Compact Operating Instructions – MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE/DRP
4Mounting MOVI-SWITCH®with option P22A close to the motor
Mechanical Installation (all MOVI-SWITCH®variants)
4.1.3 Installation in damp locations or in the open
Observe the following notes for mounting the MOVI-SWITCH®drive in damp areas or
in the open:
• Use suitable cable glands for the supply leads (use reducing adapters if necessary).
• Coat the threads of cable glands and filler plugs with sealing compound and tighten
them well – then coat them again.
• Seal the cable entries well
• Clean the sealing faces of the terminal box cover/MOVI-SWITCH®control unit well
before reassembly.
• Touch up the corrosion protection coating if damaged anywhere
• Check degree of protection according to nameplate
4.2 Mounting MOVI-SWITCH®with option P22A close to the motor
The following figure shows the mounting dimensions for mounting the MOVI-SWITCH®
terminal box with option P22A close to the motor.
986364683
170mm
65mm
M6
M6

Compact Operating Instructions – MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE/DRP 13
4
Tightening torques
Mechanical Installation (all MOVI-SWITCH®variants)
4.3 Tightening torques
4.3.1 MOVI-SWITCH®control unit/terminal box
Tighten the screws on the MOVI-SWITCH®control unit with 3.0 Nm (26.6 lb.in) working
diagonally across.
4.3.2 Cable glands
It is essential to observe the manufacturer's specifications for the cable glands.
4.3.3 Blanking plug cable glands
Tighten blanking plugs with 2.5 Nm (22.1 lb.in).
4.3.4 Modular terminal box
For fastening the terminal box on the mounting plate, tighten screws with 3.3 Nm
(29.2 lb.in).
986785291
986793739
986891403

14 Compact Operating Instructions – MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE/DRP
4Tightening torques
Mechanical Installation (all MOVI-SWITCH®variants)
4.3.5 Tightening torques for terminals (MOVI-SWITCH®-1E)
Use the following tightening torques for terminals during installation:
4.3.6 Tightening torques for terminals (MOVI-SWITCH®-2S)
Use the following tightening torques for terminals during installation:
[1] 1.6 – 2.0 Nm (14.2 lb.in – 17.7 lb.in)
[2] 0.3 – 0.5 Nm (3.0 lb.in – 4.4 lb.in)
[3] 0.5 – 0.7 Nm (4.4 lb.in – 6.2 lb.in)
[4] 1.2 – 1.6 Nm (10.6 lb.in – 14.2 lb.in)
[5] 0.5 – 0.7 Nm (4.4 lb.in – 6.2 lb.in)
[6] 2.0 – 2.4 Nm (17.7 lb.in – 21.2 lb.in)
1308951051
[2]
[3] [4] [5]
[6]
[1]
[1] 0.5 – 0.7 Nm (4.4 lb.in – 6.2 lb.in)
[2] 0.5 – 0.7 Nm (4.4 lb.in – 6.2 lb.in)
[3] 0.8 – 1.1 Nm (7.1 lb.in – 9.7 lb.in)
[4] 1.2 – 1.6 Nm (10.6 lb.in – 14.2 lb.in)
[5] 2.0 – 2.4 Nm (17.7 lb.in – 21.2 lb.in)
[6] 0.5 – 0.7 Nm (4.4 lb.in – 6.2 lb.in)
[7] 0.5 – 0.7 Nm (4.4 lb.in – 6.2 lb.in)
[8] 2.0 – 2.4 Nm (17.7 lb.in – 21.2 lb.in)
1370327179
MSW-2S
X4
X5
[1]
[5] [6] [7] [8]
[2] [3] [4]

Compact Operating Instructions – MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE/DRP 15
5
Installation instructions
Electrical Installation
5 Electrical Installation
5.1 Installation instructions
5.1.1 Connecting supply system leads
• The rated voltage and frequency of the MOVI-SWITCH®drive must correspond to
the data for the supply system (line).
• Cable cross section: According to input current Iline for rated power (see the
"Technical Data" chapter in the "MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE/
DRP" operating instructions).
• Use conductor end sleeves without insulating shrouds (DIN 46228 part 1, material E-
CU).
• Install line fuses at the beginning of the supply system line behind the supply bus
junction. Use D, DO, NH fuses or circuit breakers. Select the fuse size according to
the cable cross section.
5.1.2 Connecting the DC 24 V power supply
• Supply the MOVI-SWITCH®drive either via the external DC 24 V voltage and/or via
AS-Interface data line1) .
5.1.3 Conventional control (via binary commands)
• Connect the required control leads2) (e.g. CW/Stop, CCW/Stop)
• Route the control cables separately from the supply system cables.
5.1.4 Permitted wire cross section of the terminals
Permitted wire cross section of the MOVI-SWITCH®1E terminals and diameter of the
terminal studs:
Permitted cable cross section of the MOVI-SWITCH®-2S terminals:
1) For MSW-2S CK0 type only
2) For MSW-1E and MSW-2S CB0 only
Terminal board MOVI-SWITCH®
module
(for internal wiring)
BGW brake control
(only with brake motor, for internal wiring)
Terminal stud Control terminals Field wiring power
terminals
Control terminals
M4
0.25 mm2– 1.0 mm21.0 mm2– 4.0 mm2
(2 x 4.0 mm2)
0.25 mm2– 1.0 mm2
(2 x 0.75 mm2)
AWG22 – AWG17 AWG17 – AWG10
(2 x AWG10)
AWG22 – AWG17
(2 x AWG18)
Field wiring power terminals Control terminals (for internal wiring)
1.0 mm2 – 4.0 mm2 (2 x 4.0 mm2) 0.25 mm2 – 1.0 mm2 (2 x 0.75 mm2)
Except for OK terminals X6/X11: 1 x 0.25 mm2– 0.75 mm2
AWG17 – AWG10 (2 x AWG10) AWG22 – AWG17 (2 x AWG18)
Except for OK terminals X6/X11: 1 x AWG22 – AWG18

16 Compact Operating Instructions – MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE/DRP
5Installation instructions
Electrical Installation
5.1.5 Protective devices
MOVI-SWITCH®drives are equipped with integrated protection devices against motor
overload. External motor protection elements are not necessary.
5.1.6 Notes on PE connection
WARNING
Insufficient protection of the leads.
Severe or fatal injuries.
• When mounting MOVI-SWITCH®close to the motor, the applicable regulations
concerning line protection must be observed.
• The protection of the lead between MOVI-SWITCH®and the motor must be
ensured by appropriate dimensioning or optional line protection components.
DANGER
Incorrect connection of PE.
Death, severe injuries or damage to property from electric shock.
• The permitted tightening torque for the screw fitting is 2.0 to 2.4 Nm (18...21 lb.in).
• Observe the following notes regarding the PE connection:
Prohibited assembly
sequence
Recommendation: Assembly with
forked cable lug
Permitted for all cross sections
Assembly with thick solid wire
Permitted for cross sections up to
max. 2.5 mm2
323042443 323034251 323038347
[1] Forked cable lug suitable for M5 PE screws
[1]
M5
2.5 mm²
M5

Compact Operating Instructions – MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE/DRP 17
5
Installation instructions
Electrical Installation
5.1.7 Installation above 1000 m asl
MOVI-SWITCH®drives with line voltages of 380 to 240 V or 380 to 500 V, can be used
in altitudes of 1000 m and up to a maximum of 4000 m above sea level under the
following conditions.1)
• The rated continuous power is reduced based on the reduced cooling above 1000 m
(see the "Technical Data" chapter in the "MOVI-SWITCH®-1E/-2S with AC Motor
DRS/DRE/DRP" operating instructions).
• Above 2000 m above sea level, the air and creeping distances are only sufficient for
overvoltage class 2. If the installation calls for overvoltage class 3, you will have to
install additional external overvoltage protection to limit overvoltage peaks to 2.5 kV
phase-to-phase and phase-to-ground.
• If safe electrical disconnection is required, it must be implemented outside the device
at altitudes above 2000 m asl (safe electrical disconnection in accordance with
EN 61800-5-1).
• The permitted rated supply voltage of 3 x 500 V up to 2,000 m asl is reduced by 6 V
for every 100 m to a maximum of 3 x 380 V at 4,000 m asl.
5.1.8 UL-compliant installation
• Use only copper conductors with a permitted temperature range (60/75°C) as
connection cables.
• MOVI-SWITCH®is suited for operation on voltage supply systems with grounded
star (TN and TT systems) supplying a maximum supply current of AC 5000 A and
having a maximum voltage of AC 500 V. The performance data of the fuses must not
exceed 25 A/600 V.
• Only use tested units with a limited output voltage (V ≤DC 30 V) and limited output
current (I ≤8 A) as an external DC 24 V voltage source.
• The UL certification only applies to operation on voltage supply systems with
voltages to ground up to a maximum of 300 V.
1) The maximum altitude is limited by creeping distances and flameproof components, such as electrolytic
capacitors.

18 Compact Operating Instructions – MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE/DRP
5MOVI-SWITCH®-1E
Electrical Installation
5.2 MOVI-SWITCH®-1E
5.2.1 Description of the control signals (M12 connection)
5.2.2 Connecting MOVI-SWITCH®-1E
PIN Assignment Function
1 24 V Power supply voltage DC 24 V
2RUN DC 24 V control signals, high = start, low = stop
3 ⬜Reference potential 0V24
4OK Checkback signal ready for operation, DC 24 V,
high = ready for operation, low = overtemperature or no 24 V supply
1302084363
[1]
[2]
CW
CCW
M12 connector AVS1 (standard coding)
M12 socket (standard coding)
Clockwise rotation
Counterclockwise rotation
Wired at the factory
W2 U2 V2
U1 V1 W1
RUN 24 VDC
OK
4
2
1
3
21
34
PE L1 L2 L3 (CW)
(L2 L1 L3) (CCW)
[2]
[1]
MSW

Compact Operating Instructions – MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE/DRP 19
5
MOVI-SWITCH®-1E
Electrical Installation
5.2.3 MOVI-SWITCH®-1E with optional ASA3 plug connector
1373049995
[1]
[2]
[3]
[4]
CW
CCW
M12 connector AVS1 (standard coding)
M12 socket (standard coding)
ASA3 plug connector (plug)
Plug connector (socket)
Clockwise rotation
Counterclockwise rotation
Wired at the factory
RUN 24VDC
OK
4
2
1
3
21
34
W2 U2 V2
U1 V1 W1
10
[4]
L3 L2 L1 (CW)
(L3 L1 L2) (CCW)
[2]
[3]
[1]
MSW
6789
1234 5
12345
67
8910

20 Compact Operating Instructions – MOVI-SWITCH®-1E/-2S with AC Motor DRS/DRE/DRP
5MOVI-SWITCH®-2S/CB0 (binary control)
Electrical Installation
5.3 MOVI-SWITCH®-2S/CB0 (binary control)
5.3.1 Connector assignment for MOVI-SWITCH®-2S/CB0 control unit
The following illustration shows the assignment of the X102 and X101 plugs.
1368821131
PIN Assignment Function
X102 1 24 V Power supply voltage DC 24 V, jumpered with X101/1
2RControl signal DC 24 V for CW rotation, high = start, low = stop
(jumpered with X101/2)
3 ⬜Reference potential 0V24 (jumpered with X101/3)
4L Control signal DC 24 V for CCW rotation, high = start, low = stop
X101
1)
1) Plug is compatible with M12 plug of MOVI-SWITCH®type 1E
1 24 V Power supply voltage DC 24 V, (jumpered with X102/1)
2RControl signal DC 24 V for CW rotation, high = start, low = stop
(jumpered with X102/2)
3 ⬜Reference potential 0V24 (jumpered with X102/3)
4OK Checkback signal ready for operation, DC 24 V,
high = ready for operation
4
2
1
3
24 V
L
0V
R
X102
4
2
1
3
24 V
OK
0V
R
X101
X102 X101
INFORMATION
If angular plug connectors are used for the connection for X102 and X101, they can
only be mounted in the position shown in the following figure!
For this reason, it is recommended using straight plug connectors (see following
figure).
996605323