Shadow-Caster SCM-PD-PLUS User manual

Standard Layout
SCM-PD-PLUS with
SCR-24-CC Underwater Lights
REVISED
March 17th 2021
HOW TO OPERATE
Power On/Off
Press Button Change Color or Color
Rotation Scheme
Press and Hold Button for 2 seconds
Step through modes: Solid Color / Fade /
Strobe
SCR-24-CC Underwater Lights
SCM-PD-PLUS
(Includes 6 X 7.5A Fuses)
Remove Bypass jumper for
normal switch operation
Battery
24V or 12V DC
Breaker
BluePWMcontroller
wiresarenotconnected
ifonlyusingaswitch.
Breaker
12V DC
Power Source
Green PWM controller wires
are not connected and should
be cut and capped when only
using a switch
LIGHT ENABLE DIP SWITCH SETTINGS
(from left to right counting up)
Light 1 Enable
1 2 3 4
Light 2 Enable Light 3 Enable Light 4 Enable
Light 1 Disable Light 2 Disable Light 3 Disable Light 4 Disable
5 6
Light 5 Enable
Light 5 Disable
Light 6 Enable
Light 6 Disable
Indicates recommended settings for this installation
MODE DIP SWITCH SETTINGS
(from left to right counting up)
Network Enable
123
Chase Mode On Extended Color
Range Enabled
Network Disable Chase Mode Off Extended Color
Range Disabled
Indicates recommended settings for this installation
are not connected and should
be cut and capped when only
using a switch
Pre Wired Switch
(included with SCM-PD-PLUS)

Standard Layout
SCM-PD-PLUS with
SCM-10-EXT-CC Underwater Lights
REVISED
March 17th 2021
HOW TO OPERATE
Power On/Off
Press Button Change Color or Color
Rotation Scheme
Press and Hold Button for 2 seconds
Step through modes: Solid Color / Fade /
Strobe
SCM-10-EXT-CC Underwater Lights
SCM-PD-PLUS
(Includes 6 X 7.5A Fuses)
Remove Bypass jumper for
normal switch operation
Battery
24V or 12V DC
Breaker
BluePWMcontroller
wiresarenotconnected
ifonlyusingaswitch.
Breaker
12V DC
Power Source
MODE DIP SWITCH SETTINGS
(from left to right counting up)
Network Enable
123
Chase Mode On Extended Color
Range Enabled
Network Disable Chase Mode Off Extended Color
Range Disabled
Indicates recommended settings for this installation
LIGHT ENABLE DIP SWITCH SETTINGS
(from left to right counting up)
Light 1 Enable
1 2 3 4
Light 2 Enable Light 3 Enable Light 4 Enable
Light 1 Disable Light 2 Disable Light 3 Disable Light 4 Disable
5 6
Light 5 Enable
Light 5 Disable
Light 6 Enable
Light 6 Disable
Indicates recommended settings for this installation
Green PWM controller wires
are not connected and should
be cut and capped when only
using a switch
Pre Wired Switch
(included with SCM-PD-PLUS)

Standard Layout
SCM-ZC-KIT & SCM-PD-PLUS with SCM-10-EXT-CC
Underwater Lights & 4 Zones of RGB Lights
REVISED
March 19th 2021
HOW TO OPERATE
All Press twice to turn all zones on
Zone (1-4) Press and then set desired color
and effect for the zone
Mode Press to step through modes:
Single Color Fade / Multi-Color Fade /
Multi-Color Change / Strobe
Sync Press to step through sync options:
Full Spectrum Music Sync / Color Rotate
Music Sync / Single Color Music Sync
Click here to view our ‘Zone Controller
Operations Guide’ for full instructions
SCM-MZ-LC DIP SWITCH SETTINGS
(from left to right counting up)
Zone 1 RGB
1234
Zone 2 RGB Zone 3 RGB Zone 4 RGB
Zone 1 RGBW Zone 2 RGBW Zone 3 RGBW Zone 4 RGBW
SCM-PD-PLUS MODE DIP SWITCH SETTINGS
(from left to right counting up)
Network Enable
123
Chase Mode On Extended Color
Range Enabled
Network Disable Chase Mode Off Extended Color
Range Disabled
Indicates recommended settings for this installation
SCM-PD-PLUS LIGHT ENABLE DIP SWITCH SETTINGS
(from left to right counting up)
Light 1 Enable
1 2 3 4
Light 2 Enable Light 3 Enable Light 4 Enable
Light 1 Disable Light 2 Disable Light 3 Disable Light 4 Disable
5 6
Light 5 Enable
Light 5 Disable
Light 6 Enable
Light 6 Disable
Indicates recommended settings for this installation
SCM-ZC- REMOTE
Zone Controller Remote
SCM-MZ-LC
Multi-Zone Lighting Controller
3.5mm Female
Audio Jack
for music sync
4 X Channels of RGB Lighting
Supports up 15A per channel
Shadow-NET®output
to sync with other
Shadow-NET®devices
RGB Zone 1 RGB Zone 2 RGB Zone 3 RGB Zone 4
SCM-10-EXT-CC Underwater Lights
Breaker
SCM-PD-PLUS
(Includes 6 X 7.5A Fuses)
Remove Bypass jumper for
normal switch operation or
keep Bypass Jumper in
place if not using a switch
Green PWM controller wires
are not connected and
should be cut and capped
when only using a switch
Optional Pre
Wired Switch
(included with
SCM-PD-PLUS)
Battery
24V or 12V DC
24V or 12V DC
12V DC
Power Source
Learn more about boat underwater lights we have.