Sharp RJ33N3AD0LT User manual

Nov 28 2013

RJ33N3AD0LG
○ Handle this document carefully for it contains material protected by international copyright law.
Any reproduction, full or in part, of this material is prohibited without the express written permission
of the company.
○ When using the products covered herein, please observe the conditions written herein and the
precautions outlined in the following paragraphs. In no event shall the company be liable for any
damages resulting from failure to strictly adhere to these conditions and precautions.
（1） Please do verify the validity of this part after assembling it in customer’s products, when
customer wants to make catalogue and instruction manual based on the specification sheet
of this part.
（2） The products covered herein are designed and manufactured for the following application areas.
When using the products covered herein for the equipment listed in Paragraph (3), even for
the following application areas, be sure to observe the precautions given in Paragraph (3).
Never use the products for the equipment listed in Paragraph (4).
Office electronics
・ Instrumentation and measuring equipment
・ Machine tools
・ Audiovisual equipment
・ Home appliance
・ Communication equipment other than for trunk lines
（3） Those contemplating using the products covered herein for the following equipment which
demands high reliability, should first contact a sales representative of the company and then
accept responsibility for incorporating into the design fail-safe operation, redundancy, and
other appropriate measures for ensuring reliability and safety of the equipment and the
overall system.
・ Control and safety devices for airplanes, trains, automobiles, and other transportation
equipment
・ Mainframe computers
・ Traffic control systems
・ Gas leak detectors and automatic cutoff devices
・ Rescue and security equipment
・ Other safety devices and safety equipment, etc
（4） Do not use the products covered herein for the following equipment which demands extremely
high performance in terms of functionality, reliability, or accuracy.
・ Aerospace equipment
・ Communications equipment for trunk lines
・ Control equipment for the nuclear power industry
・ Medical equipment related to life support, etc.
（5） Please direct all queries and comments regarding the interpretation of the above three Paragraphs
to a sales representative of the company.
○ Please direct all queries and regarding the products covered herein to a sales representative of the company.

RJ33N3AD0LG 1
CONTENTS
1DESCRIPTION ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 2
1.1 Features
1.2 Applications
2ARRANGEMENT OF PIXELS AND COLOR FILTERS ‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 3
3PIN CONFIGURATION ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 4
4ABSOLUTE MAXIMUM RATINGS ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 4
4.1 CCD, VDr Power sequence
5RECOMMENDED OPERATING CONDITIONS ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 6
6CHARACTERISTICS ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 7
7DRIVE TIMING CHART ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 8
8EXAMPLE OF STANDARD OPERATING CIRCUIT ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 16
9PECIFICATION FOR BLEMISH ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 18
10 PRECAUTIONS ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 20
9.1 PackageBreakage
9.2 ElectrostaticDamage
9.3 DustandContamination
9.4 Other
11 PACKAGE OUTLINES AND PACKING SPECIFICATIONS ‥‥‥‥‥‥‥‥‥‥‥‥ 23

RJ33N3AD0LG 2
RJ33N3AD0LT
1/3-type Progressive Scan Color CCD Area Sensor with 2M Pixels
1 DESCRIPTION
The RJ33N3AD0LT is a 1/3-type solid-state image sensor that consists of PN photo-diodes
andCCDs(charge-coupled devices). With approximately 2,174k pixels, the sensor provides
a high resolution stable color image.
1 . 1 Features
1）Opticalsize : 6.168 mm (Aspect ratio 16:9)
2）Progressive scan format
3）Square pixel
4）Number of total pixels :Horizontal 1984 ×vertical 1096
Number of image pixels :Horizontal 1928 ×vertical 1088
Number of effective pixels :Horizontal 1920 ×vertical 1080
Pixel pitch :Horizontal 2.8μm ×vertical 2.8μm
Number of optical black pixels :Horizontal ;28 front and 28rear
:Vertical ;6 front and 2 rear
Number of dummy bits :Horizontal ;4 front and 4 rear
:Vertical ;2 front
5）R, G and B primary color mosaic filters
6）Supports monitoring mode
7）Built-in overflow drain voltage output circuit, and reset gate voltage circuit
8）Variable electronic shutter
9）Low fixed pattern noise and lag
10）No burn-in and no image distortion
11）Blooming suppression structure
12）Built-in output amplifier
13）N-type silicon substrate, N-MOS process,
Not designed or rated as radiation hardened
14）Global shutter
15）Near infrared high sensitivity
16）40-pin 0.65mm pitch LCC, ceramics package
1.2 Applications
1）Electronic still cameras, video capturing devices for PCs, etc
2）Pattern recognition
in
"iSHCCDⅡ", "iSHCCD" and "iSHartina" are the trademarks of Sharp Corporation.
The "iSHCCDⅡ" is an advanced CCD image sensor that drastically improves light efficiency by including
near-infrared light region as a basic structure of "iSHCCD".
The "iSHartina" series is a key device group of Sharp which realizes a next-generation sensing world.
The circuit diagram and others included in this specifications are intended for use to explain typical application
examples. Therefore, we take no responsibility for any problem as may occur due to the use of the included circuit
and for any problem with industrial proprietary rights or other rights.
2,073k effective
6.168
1080
1,920

RJ33N3AD0LG 3
2 ARRANGEMENT OF PIXELS AND COLOR FILTERS
Pin arrangement of the vertical readout clock
(1, 1088)
1AGBGBG BGBGB
1BRGRGR GRGRG
1CGBGBG BGBGB
1DRGRGR GRGRG
1AGBGBG BGBGB
1BRGRGR GRGRG
1CGBGBG BGBGB
1DRGRGR GRGRG
1AGBGBG BGBGB
1BRGRGR GRGRG
1CGBGBG BGBGB
1DRGRGR GRGRG
(
1, 1
)
(
1928,1
)
(1928, 1088)
Optical black
（28pixels）
Optical black
（28 pixels）
1 pin
Image pixels
1928（H）× 1088（V）
Optical black
（6 pixels）
Dummy bit（2 pixels）
Optical black
（2 pixels）