Sharp MX-7001N Series Installation and operating manual

T
T
rou
ou
bleshooting
leshooting
DIGITAL FULL COLOUR MULTIFUNCTIONAL SYSTEM
Sa
Sa
fety Guide
ety Guide
Safety Guide
Before installing this product, be sure to read the
"CAUTIONS" and "INSTALLATION
REQUIREMENTS" sections.
Keep this manual close at hand for reference
whenever needed.
Troubleshooting
In the unlikely event of you experiencing a
problem with this product, please refer to this
manual before requesting service.
The contents of this manual are grouped by
situation.
The chapters of the manual appear on the cover.
FACSIMILE
CAUTIONS
INSTALLATION REQUIREMENTS
SUPPLIES
SPECIFICATIONS
INFORMATION ON DISPOSAL
TO THE ADMINISTRATOR OF THE MACHINE
REMOVING MISFEEDS
COPYING
PRINTING
SCANNING
DOCUMENT FILING
INSTALLATION
OTHER PROBLEMS
MX-6201N
MX-7001N
MODEL: MX-5500N
MX-6200N
MX-7000N

EMC (this machine and peripheral devices)
Caution!
For complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Shielded network cable and USB cable must be used with this equipment to maintain compliance with standards.
Warning:
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate measures.
This machine contains the software having modules developed by Independent JPEG Group.
Required in IEC-950 (EN 60 950) - Europe
• The equipment should be installed near an accessible socket outlet for easy disconnection.
Required in Appendix ZB of BS 7002 (En 60 950) — United Kingdom
MAINS PLUG WIRING INSTRUCTIONS
The mains lead of this equipment is already fitted with a mains plug which is either a non-rewireable
(moulded) or a rewireable type. Should the fuse need to be replaced, a BSI or ASTA approved fuse
to BS1362 marked or and of the same rating as the one removed from the plug must
be used.
Always refit the fuse cover after replacing the fuse on the moulded plug. Never use the plug without
the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied
either cut-off the moulded plug (if this type is fitted) or remove by undoing the screws if a rewireable
plug is fitted and fit an appropriate type observing the wiring code below.
DANGER: The fuse should be removed from the cut-off plug and the plug destroyed immediately
and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted
elsewhere into a 13A socket outlet as a serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
GREEN-AND-YELLOW: Earth
BLUE: Neutral
BROWN: Live
As the colours of the wires in this mains lead may not correspond with coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND YELLOW must be connected to the terminal in the plug
which is marked with the letter E, or by the safety earth symbol Å@, or coloured green or green-
and-yellow.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter
Nor coloured black.
The wire which is coloured BROWN must be connected to the terminal which is marked with the
letter Lor coloured red.
If you have any doubt, consult a qualified electrician.
WARNING: THIS APPARATUS MUST BE EARTHED.
➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢
➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢
➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣
➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢

For the users of the fax function
FAX interface cable and Line cable:
These special accessories must be used with the device.
Notice for Users in Europe
This equipment has been designed to work on the British analogue public switched telephone network.
This equipment has been tested according to the pan-European TS103 021 regulation.
It will operate on all analogue telephone networks which comply with the TS103 021.
Please contact your dealer or network operator, if you are not sure whether your network operates according to
TS103 021.
The Declaration of Conformity can be viewed at the following URL address.
http://www.sharp.de/doc/MX-FXX1.pdf

1
Contents
Warranty
While every effort has been made to make this document as accurate and helpful as possible, SHARP Corporation makes no
warranty of any kind with regard to its content. All information included herein is subject to change without notice. SHARP is not
responsible for any loss or damages, direct or indirect, arising from or related to the use of this operation manual.
©Copyright SHARP Corporation 2007. All rights reserved. Reproduction, adaptation or translation without prior written permission is
prohibited, except as allowed under copyright laws.
CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Laser information . . . . . . . . . . . . . . . . . . . . . . . . . . 3
INSTALLATION REQUIREMENTS . . . . . . . . . . . . . 4
SUPPLIES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Storage of supplies. . . . . . . . . . . . . . . . . . . . . . . . . 5
Supply of spare parts and consumables . . . . . . . . 5
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Machine specifications / copier specifications . . . . 6
Continuous copying speeds . . . . . . . . . . . . . . . . . . 8
Printable sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Ambient environment . . . . . . . . . . . . . . . . . . . . . . . 8
Acoustic noise emission (measurement according to
ISO7779) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Emission concentration (measurement according to
RAL-UZ62: Edition Jan. 2002) . . . . . . . . . . . . . . . . 9
Automatic document feeder specifications. . . . . . . 9
Large capacity tray (MX-LCX2) specifications . . . 10
Large capacity tray (MX-LCX3) specifications . . . 10
Finisher specifications . . . . . . . . . . . . . . . . . . . . . 11
Saddle stitch finisher specifications . . . . . . . . . . . 12
Punch module specifications
(for finisher / saddle stitch finisher). . . . . . . . . . . . 13
Inserter specifications. . . . . . . . . . . . . . . . . . . . . . 14
Printer specifications . . . . . . . . . . . . . . . . . . . . . . 15
Network scanner / Internet Fax specifications . . . 20
Pull scan function (TWAIN) specifications . . . . . . 16
Facsimile specifications . . . . . . . . . . . . . . . . . . . . 17
INFORMATION ON DISPOSAL . . . . . . . . . . . . . . . 18
A. Information on Disposal for Users (private
households) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
B. Information on Disposal for Business Users . . 18
TO THE ADMINISTRATOR OF THE MACHINE . . 20
Factory default passwords . . . . . . . . . . . . . . . . . . 20
Forwarding all transmitted and received data to the
administrator (document administration function). . . .20
For the users of the fax function . . . . . . . . . . . . . . . . .21
Trademark acknowledgments. . . . . . . . . . . . . . . . . . .22
Note:
• Considerable care has been taken in preparing this manual. If you have any comments or concerns about the manual, please
contact your dealer or nearest authorised service representative.
• This product has undergone strict quality control and inspection procedures. In the unlikely event that a defect or other problem is
discovered, please contact your dealer or nearest authorised service representative.
• Aside from instances provided for by law, SHARP is not responsible for failures occurring during the use of the product or its
options, or failures due to incorrect operation of the product and its options, or other failures, or for any damage that occurs due
to use of the product.
• This manual contains references to the fax function. However, please note that the fax function is not available in some countries
and regions.
Products that have earned the ENERGY STAR®are designed to protect the environment
through superior energy efficiency.

2
CAUTIONS
1. Do not touch the transfer belt. Scratches or smudges on the transfer belt will
cause dirty prints.
2. The fusing unit is extremely hot. Exercise care in this area.
3. Do not look directly at the light source. Doing so may damage your eyes.
4. When the machine is installed, the adjusters (4) must be lowered to the floor
to secure the machine (prevent it from moving).
Rotate the adjusters in the locking direction until they are in firm contact with
the floor.
If you find it necessary to reposition the machine due to rearrangement of
your office layout or other reason, retract the adjusters from the floor, turn off
the power, and then move the machine.
(After moving the machine, lower the adjusters again to secure the machine.)
5. Do not make any modifications to this machine. Doing so may result in
personal injury or damage to the machine.
6. The machine is heavy. To prevent injury when moving the machine, it is
recommended that it be moved by four or more persons.
7. Do not make copies of anything which is prohibited from copying by law. The
following items are normally prohibited from printing by national law. Other
items may be prohibited by local law.
●Money ●Stamps ●Bonds ●Stocks
●Bank drafts ●Checks ●Passports ●Driver's licences
8. Do not use a flammable spray to clean the machine. If gas from the spray
comes in contact with hot electrical components or the fusing unit inside the
machine, fire or electrical shock may result.
9. Do not throw toner, a toner container (toner cartridge), or a waste toner box into a fire. Toner may fly and cause
burns.
10. Store toner, toner containers (toner cartridges), and waste toner boxes out of the reach of children.
The machine includes the document filing function, which stores document image data on the machine's hard drive. Stored
documents can be called up and printed or transmitted as needed. If a hard drive failure occurs, it will no longer be possible to call
up the stored document data. To prevent the loss of important documents in the unlikely event of a hard drive failure, keep the
originals of important documents or store the original data elsewhere.
With the exception of instances provided for by law, Sharp Corporation bears no responsibility for any damages or loss due to the
loss of stored document data.
"BATTERY DISPOSAL"
THIS PRODUCT CONTAINS A LITHIUM PRIMARY MEMORY BACK-UP BATTERY THAT MUST BE DISPOSED OF PROPERLY.
PLEASE CONTACT YOUR LOCAL SHARP DEALER OR AUTHORISED SERVICE REPRESENTATIVE FOR ASSISTANCE IN
DISPOSING OF THIS BATTERY.
Each instruction also covers the optional units used with these products.
Fusing unit
Adjuster
Lock Release

3
CAUTIONS
Laser information
s
Wave length Colour: 785 nm +10 nm
-15 nm
B/W: 788 nm +12 nm
-15 nm
Pulse times
(North America and Europe)
Colour:
MX-5500N/6200N/6201N/
7000N/7001N *1(4.9 µs ±4.9 ns)/7 mm
MX-5500N/6200N/7000N : (3.5 µs ±3.5 ns)/7 mm
MX-6201N/7001N : (2.8 µs ±2.8 ns)/7 mm
*1: heavy paper
B/W:
MX-5500N/6200N/6201N/
7000N/7001N *1(4.8 µs ±4.8 ns)/7 mm
MX-5500N/6200N/6201N : (4.0 µs ±4.0 ns)/7 mm
MX-7000N/7001N : (3.4 µs ±3.4 ns)/7 mm
Output power Max 0.8 mW
At the production line, the output power of the scanner unit is adjusted to 0.40 MILLIWATT PLUS 5% and is maintained constant by
the operation of the Automatic Power Control (APC).
Caution
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
This Digital Equipment is CLASS 1 LASER PRODUCT (IEC 60825-1 Edition 1.2-2001)
For Europe:
CLASS 1 LASER PRODUCT
LASER KLASSE 1
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
CAUTION
CLASS 3B INVISIBLE LASER
RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED.
AVOID EXPOSURE TO BEAM.
VORSICHT
UNSICHTBARE
LASERSTRAHLUNG DER
KLASSE 3B, WENN
ABDECKUNG GEÖFFNET UND
SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT. NICHT DEM
STRAHL AUSSETZEN.
ADVARSEL
USYNLIG LASERSTRÅLNING
AF KLASSE 3B VED ÅBNING,
NÅR SIKKERHEDSBRYDERE
ER UDE AF FUNKTION. UNDGÅ
UDSÆTTELSE FOR STRÅLING.
ADVARSEL
USYNLIG KLASSE 3B
LASERSTRÅLNING NÅR
DEKSEL ÅPNES OG
SIKKERHEDSLÅS BRYTES .
UNNGÅ EKSPONERING FOR
STRÅLEN.
VARNING
OSYNLIG LASERSTRÅLNING
KLASS 3B NÄR DENNA DEL ÄR
ÖPPNAD OCH SPÄRRAR ÄR
URKOPPLADE. UNDVIK
EXPONERING FÖR STRÅLEN.
VARO!
AVATTAESSA JA
SUOJALUKITUS OHITETTAESSA
OLET ALTTIINA NÄKYMÄTÖNTÄ
LUOKAN 3B LASERSÄTEILYLLE.
ÄLÄ KATSO SÄTEESEEN.
The above label is affixed to the laser
unit inside the machine.

4
INSTALLATION REQUIREMENTS
Improper installation may damage this product. Please note the following during initial installation and whenever the
machine is moved.
1. The machine should be installed near an accessible
power outlet for easy connection.
2. Be sure to connect the power cord only to a power
outlet that meets the specified voltage and current
requirements. Also make certain the outlet is properly
grounded.
• For the power supply requirements, see the name
plate in the lower corner of the left side of the
machine.
Connect the machine to a power outlet which is not
used for other electric appliances. If a lighting fixture is
connected to the same outlet, the light may flicker.
3. Do not install the machine in areas that are:
• damp, humid, or very dusty
• exposed to direct sunlight
• poorly ventilated
• subject to extreme temperature or humidity
changes, e.g., near an air conditioner or heater.
4. Be sure to allow the required space around the
machine for servicing and proper ventilation.
5. The machine includes a built-in hard drive. Do not
subject the machine to shock or vibration. In
particular, never move the machine while the power is
on.
45 cm
(17-23/32")
30 cm
(11-13/16")
30 cm
(11-13/16")
A small amount of ozone is produced within the printer during operation. The emission level is insufficient to cause any health
hazard.
NOTE:
The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m3) calculated as an 8 hr. time-weighted average
concentration.
However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier in a ventilated
area.

5
SUPPLIES
Standard supplies for this product that can replaced by the user include paper, toner cartridges, and staple cartridges for
the finisher.
Be sure to use only SHARP-specified products for the toner cartridges, finisher staple cartridge, saddle stitch finisher
staple cartridge, and transparency film.
Storage of supplies
Proper storage
1. Store the supplies in a location that is:
• clean and dry,
• at a stable temperature,
• not exposed to direct sunlight.
2. Store paper in the wrapper and lying flat.
3. Paper stored in packages standing up or out of the wrapper may curl or become damp, resulting in paper misfeeds.
Storing toner cartridges
Store a new toner cartridge box horizontally. Do not store it standing on end. If stored standing on end, the toner may not
distribute well even after shaking the cartridge vigorously, and will remain inside the cartridge without flowing out.
Staple cartridge
The finisher and saddle stitch finisher require the following staple cartridge:
AR-SC2 (for finisher and saddle stitch finisher)
Approx. 5000 per cartridge x 3 cartridges
AR-SC3 (for saddle stitch finisher only)
Approx. 2000 per cartridge x 3 cartridges
Supply of spare parts and consumables
The supply of spare parts for repair of the machine is guaranteed for at least 7 years following the termination of
production. Spare parts are those parts of the machine which may break down within the scope of the ordinary use of
the product, whereas those parts which normally exceed the life of the product are not to be considered as spare parts.
Consumables too, are available for 7 years following the termination of production.
For best copying results, be sure to use only Sharp Genuine Supplies which are designed,
engineered, and tested to maximize the life and performance of Sharp products. Look for the
Genuine Supplies label on the toner package.
GENUINE SUPPLIES

6
SPECIFICATIONS
Machine specifications / copier specifications
*1 First copy out time is measured with original on the document glass in full ready condition with fuser at operating temperature and
mirror motor at operating speed in each of black and white mode and colour mode, actual time may vary based on environment
conditions.
*2 It may not be possible to use this size in some countries and regions.
Name Digital Full Colour Multifunctional System MX-5500N/6200N/6201N/7000N/7001N
Type Console
Photoconductive type OPC drum
Printing method Electrophotographic system (laser)
Developer system Dry-type two-component magnetic brush development
Fusing system Heat rollers
Scanning resolution
Document glass
Black and white scanning: 600 x 300 dpi (factory default values), 600 x 600 dpi
Colour scanning:600 x 600 dpi (factory default values)
Duplex single pass
feeder (automatic
document feeder)
Black and white scanning: 600 x 300 dpi (factory default values), 600 x 600 dpi
Colour scanning:600 x 600 dpi (factory default values)
Printing resolution 600 x 600 dpi
Scanning gradation 10 bits
Printing gradation Black and white printing: 2 tones (1 bit)
Colour printing: 2 tones per colour (1 bit) or 16 tones per colour (4 bits)
Original sizes / types Max. A3 (11" x 17") / sheets, bound documents
Copy sizes Maximum: A3W (12" x 18") Minimum: A5R (5-1/4" x 5-3/4")
Print margins Leading edge: 4 mm (11/64") or less, trailing edge: 4 mm (11/64") or less, near edge / far edge: total
4 mm (11/64") or less
Warm-up time 295 seconds or less (MX-5500N/6200N/7000N)
320 seconds or less (MX-6201N/7001N)(at room temperature of 23°C (73.4°F) and rated voltage)
First-copy time*1
Colour copy time:7.2 seconds (MX-6201N/7001N) / 8.4 seconds (MX-5500N/6200N/7000N)
Black and white copy time: 4.0 seconds (MX-7000N/7001N)
4.5 seconds (MX-5500N/6200N/6201N)
(Portrait feeding of A4 (8-1/2" x 11") sheets from 2nd paper tray, without auto colour selection and
auto colour mode.)
Copy ratios
Variable: 25% to 400% in increments of 1%, total 376 increments (25% to 200% when the automatic
document feeder is used)
Fixed presets:
25%, 50%, 70%, 81%, 86%, 100%, 115%, 122%, 141%, 200% and 400% for AB sizes;
25%, 50%, 64%, 77%, 100%, 121%, 129%, 200% and 400% for inch
sizes.
Two reduction ratios and two enlargement ratios can be stored.
Continuous copy 999 copies
Automatic document
feeder
See "Automatic document feeder specifications".
Tray 1
Paper sizes: A4, B5*2, 8-1/2" x 11"
Paper weight: Plain paper (60 g/m2to 105 g/m2(16 lbs. to 28 lbs.))
Paper capacity: 1200 sheets (80 g/m2(21 lbs.))
Paper types: SHARP-recommended plain paper, recycled paper, and coloured paper
Tray 2
Paper sizes: A4, 8-1/2" x 11"
Paper weight: Plain paper (60 g/m2to 105 g/m2(16 lbs. to 28 lbs.))
Paper capacity: 800 sheets (80 g/m2(21 lbs.))
Paper types: SHARP-recommended plain paper, recycled paper, and coloured paper

7
SPECIFICATIONS
Machine specifications / copier specifications (Continued)
* Output tray (Centre tray) cannot be used when the finisher (MX-FNX3) or saddle stitch finisher (MX-FNX4) is installed.
Tray 3
Paper sizes: A3W, A3, B4, A4, A4R, B5, B5R, A5R, 12" x 18", 11" x 17", 8-1/2" x 14",
8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K,
16K, 16KR (Includes automatic paper size detection function.)
Paper weight: Plain paper (60 g/m2to 105 g/m2(16 lbs. to 28 lbs.)), heavy paper (106 g/m2to
209 g/m2(28 lbs. to 56 lbs.))
Paper capacity: 500 sheets (80 g/m2(21 lbs.)), transparency films 40 sheets, heavy paper 80
sheets, tab paper 40 sheets, gloss paper 40 sheets
Paper types: SHARP-recommended plain paper, recycled paper, coloured paper , heavy paper,
and transparency film
Tray 4
Paper sizes: A3W, A3, B4, A4, A4R, B5, B5R, 12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13",
8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 8K, 16K, 16KR (Includes automatic
paper size detection function.)
Paper weight: Plain paper (60 g/m2to 105 g/m2(16 lbs. to 28 lbs.)), heavy paper (106 g/m2to
209 g/m2(28 lbs. to 56 lbs.))
Paper capacity: 500 sheets (80 g/m2(21 lbs.))
Paper types: SHARP-recommended plain paper, recycled paper, coloured paper , and heavy paper
Bypass tray
Paper sizes: A3W, A3, B4, A4, A4R, B5, B5R, A5R, 12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11",
8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR (Includes automatic paper size
detection function. Entry of paper sizes up to 297 mm x 420 mm (11" x 17") is possible.)
Paper weights:
Thin paper (55 g /m
2
to 59 g /m
2
(15 lbs. to 16 lbs.)), plain paper (60 g /m
2
to 105 g /m
2
(16 lbs. to 28 lbs.)),
heavy paper (106
g /m
2
to 256 g /m
2
(28 lbs. to 68 lbs.)), envelopes (75 g /m
2
to 90 g /m
2
(20 lbs. to 24 lbs.))
Paper capacity: Standard paper 100 sheets
Paper types:
Plain paper, recycled paper, coloured paper, heavy paper, thin paper, transparency film, envelopes
(Monarch, Com-10, DL, C5)
Duplex module
Paper sizes: A3W, A3, B4, A4, A4R, B5, B5R, A5R, 12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13",
8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR
Paper weight: Plain paper (60 g/m2to 105 g/m2(16 lbs. to 28 lbs.)), heavy paper (106 g/m2to
209 g/m2(28 lbs. to 56 lbs.))
Paper types: SHARP-recommended plain paper, recycled paper, coloured paper, and heavy paper
Output tray (Centre tray)*
Output method: Face-down output
Output capacity:
250 sheets (using SHARP-recommended A4 or 8-1/2" x 11" paper)
(The maximum number of sheets that can be held varies depending on ambient conditions in the
installation location, the type of paper, and the storage conditions of the paper.)
Tray full sensor:Yes
Right tray
Output method: Face-down output
Output capacity:
100 sheets (using SHARP-recommended A4 or 8-1/2" x 11" paper)
(The maximum number of sheets that can be held varies depending on ambient conditions in the
installation location, the type of paper, and the storage conditions of the paper. Envelopes, heavy
paper (106 g/m2to 209 g/m2(28 lbs. to 56 lbs.)), and tab paper cannot be used.)
Tray full sensor:Yes
Interface port
LAN connectivity: 10Base-T / 100Base-TX
USB connectivity:
Type A connector supports USB 2.0 (Full speed)
Type B connector supports USB 2.0 (Hi speed)
Required power supply Local voltage ±10% (For the power supply requirements, see the name plate in the lower corner of
the left side of the machine.)
Power consumption 220-240V: 1.84 kW 100-127V: 1.80 kW
Dimensions
795 mm (W) x 715 mm (D) x 1225 mm (H) (31-19/64" (W) x 28-9/64" (D) x 48-7/32" (H))
Weight Approx. 209 kg(460.8 lbs.)
Overall dimensions 1130 mm (W) x 715 mm (D) (44-31/64" (W) x 28-9/64" (D)) (when bypass tray is extended)

8
SPECIFICATIONS
Continuous copying speeds*
* Copy speed during output of the second copy and following copies when performing continuous one-sided copying of the same
page (excluding offset output).
Model MX-5500N MX-6200N MX-6201N
Copy ratio 100% / Reduced / Enlarged
Copy mode Colour copying Black and
white copying Colour copying Black and
white copying Colour copying Black and
white copying
A3W, 12" x 18"
18 copies/min. 28 copies/min. 18 copies/min. 31 copies/min. 23 copies/min. 31 copies/min.
A3, 11" x 17", 8K
19 copies/min. 30 copies/min. 19 copies/min. 33 copies/min. 24 copies/min. 33 copies/min.
B4, 8-1/2" x 14",
8-1/2" x 13"
22 copies/min. 35 copies/min. 22 copies/min. 38 copies/min. 28 copies/min. 38 copies/min.
A4, B5, 8-1/2" x 11", 16K
41 copies/min. 55 copies/min. 41 copies/min. 62 copies/min. 50 copies/min. 62 copies/min.
A4R, B5R, A5R,
8-1/2" x 11"R,
7-1/4" x 10-1/2"R,
5-1/2" x 8-1/2"R, 16KR
26 copies/min. 40 copies/min. 26 copies/min. 44 copies/min. 32 copies/min. 44 copies/min.
Model MX-7000N MX-7001N
Copy ratio 100% / Reduced / Enlarged
Copy mode Colour copying Black and white copying Colour copying Black and white copying
A3W, 12" x 18"
18 copies/min. 36 copies/min. 23 copies/min. 36 copies/min.
A3, 11" x 17", 8K
19 copies/min. 38 copies/min. 24 copies/min. 38 copies/min.
B4, 8-1/2" x 14",
8-1/2" x 13"
22 copies/min. 44 copies/min. 28 copies/min. 44 copies/min.
A4, B5, 8-1/2" x 11", 16K
41 copies/min. 70 copies/min. 50 copies/min. 70 copies/min.
A4R, B5R, A5R,
8-1/2" x 11"R,
7-1/4" x 10-1/2"R,
5-1/2" x 8-1/2"R, 16KR
26 copies/min. 51 copies/min. 32 copies/min. 51 copies/min.
Printable sizes Ambient environment
Paper size Printable size Paper size Printable size
A3W* 297 x 420 mm 12" x 18"* 279 x 432 mm
A3 293 x 413 mm 11" x 17" 275 x 425 mm
B4 253 x 357 mm 8-1/2" x 14" 212 x 349 mm
A4 206 x 290 mm 8-1/2" x 13" 212 x 323 mm
B5 178 x 250 mm 8-1/2" x 11" 212 x 272 mm
A5 144 x 203 mm 5-1/2" x 8-1/2 " 136 x 209 mm
7-1/4" x 10-1/2R" 180 x 260 mm 8K 266 x 383 mm
16K 191 x 263 mm
* When printing on A3W (12" x 18") size paper using the PCL or PS printer driver,
the maximum print area is 299 mm x 450 mm.
85%
(Humidity)
60%
20%
10˚C
(54˚F)
30˚C
(86˚F)
35˚C (Temperature)
(91˚F)

9
SPECIFICATIONS
Acoustic noise emission (measurement according to ISO7779)
Emission concentration (measurement according to RAL-UZ62: Edition Jan. 2002)
Automatic document feeder specifications
MX-5500N MX-6200N / 7000N MX-6201N/7001N
Sound power level LwA
Printing mode (continuous printing) Colour 7.1 B 7.1 B 6.9 B
Black and white 7.2 B 7.3 B 7.1 B
Standby mode 5.1 B 5.1 B 5.0 B
Sound pressure level LpA (actual measurement)
Printing mode
Bystander positions Colour 56 dB (A) 56 dB (A) 55 dB (A)
Black and white 57 dB (A) 57 dB (A) 56 dB (A)
Operator positions Colour 56 dB (A) 56 dB (A) 55 dB (A)
Black and white 58 dB (A) 58 dB (A) 57 dB (A)
Standby mode Bystander positions 37 dB (A) 37 dB (A) 35 dB (A)
Operator positions 37 dB (A) 37 dB (A) 35 dB (A)
Ozone 0.02 mg/m3or less
Dust 0.075 mg/m3or less
Styrene 0.07 mg/m3or less
Original sizes
A3 to A5, 11" x 17" to 5-1/2" x 8-1/2", long paper
(max. width 297 mm (11-45/64") x max. length 800 mm (31-31/64"), scanning in mono 2 mode of
one side only is possible in fax and image scan modes)
Original weight
One-sided 35 g /m
2
to 128 g /m
2
(9 lbs. to 34 lbs.) (Paper weights from 35 g /m
2
(9 lbs.) to 49 g /m
2
(13 lbs.) require the use of slow scan mode.)
Two-sided 50
g /m
2
to 128 g /m
2
(13 lbs. to 34 lbs.)
Capacity 150 sheets (80 g/m2(21 lbs.)) Maximum stack height of 19.5 mm (3/4")

10
SPECIFICATIONS
Large capacity tray (MX-LCX2) specifications
* It may not be possible to use this size in some countries and regions.
Large capacity tray (MX-LCX3) specifications
Model MX-LCX2
Paper sizes A4, B5*, 8-1/2" x 11"
Paper weight Plain paper (60 g/m2to 105 g/m2(16 lbs. to 28 lbs.)), heavy paper (
106 g /m
2
to 209 g /m
2
( 28 lbs. to
56 lbs.)
)
Paper capacity 3500 sheets (80 g/m2(21 lbs.))
Paper types SHARP-recommended plain paper, recycled paper, coloured paper, and heavy paper
Power supply Supplied from the machine
Dimensions 370 mm (W) x 550 mm (D) x 525 mm (H) (14-9/16" (W) x 21-21/32" (D) x 20-43/64" (H))
Weight Approx. 28 kg(61.7 lbs.)
Overall dimensions when
attached to machine
1165 mm (W) x 715 mm (D) (45-55/64" (W) x 28-9/64" (D))
Model MX-LCX3
Paper sizes A3W, A3, B4, A4, A4R, B5, 12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11" 8-1/2" x 11"R
Paper weight Plain paper (60 g/m2to 105 g/m2(16 lbs. to 28 lbs.)), heavy paper (106 g/m2to 209 g/m2(28 lbs. to
56 lbs.))
Paper capacity 3000 sheets (80 g/m2(21 lbs.))
Paper types SHARP-recommended plain paper, recycled paper, coloured paper and heavy paper
Power supply Supplied from the machine
Dimensions 670 mm (W) x 570 mm (D) x 525 mm (H) (26-3/8" (W) x 22-7/16" (D) x 20-43/64" (H))
Weight Approx. 50 kg(110.2 lbs.)
Overall dimensions when
attached to machine
1465 mm (W) x 715 mm (D) (57-21/32" (W) x 28-9/64" (D))

11
SPECIFICATIONS
Finisher specifications*1
*1 Paper pass unit (MX-PBX2) is required to connect the finisher to the machine.
*2 The maximum number of sheets that can be held varies depending on ambient conditions in the installation location, the type of
paper, and the storage conditions of the paper.
*3 Up to 100 sheets of non-standard size paper, envelopes, and transparency film (A4 (8-1/2" x 11")) can be loaded.
*4 The maximum number of sheets for stapling assumes a paper weight of 80 g/m2(21 lbs.) and includes two cover sheets of
106 g/m2to 256 g/m2(28 lbs. to 68 lbs.).
Model MX-FNX3
Paper sizes A3W, A3, B4, A4, A4R, B5, B5R, A5R, 12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11",
8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR
Paper weight
Thin paper (55 g /m
2
to 59 g /m
2
(15 lbs. to 16 lbs.)) plain paper (60 g /m
2
to 105 g /m
2
(16 lbs. to 28 lbs.))
heavy paper (106 g/m2to 256 g/m2(28 lbs. to 68 lbs.)), envelopes (75 g/m2to 90 g/m2(20 lbs. to
24 lbs.))
Modes Non-staple, staple
Allowed paper sizes for
offset
A3, B4, A4, A4R, B5, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 8K, 16K
Offset distance 30 mm (1-3/16")
Tray
capacity*2
Upper tray
Non-stapling*3:
1550 sheets (A4, B5, A5R, 8-1/2" x 11",
5-1/2" x 8-1/2"R, 16K)
650 sheets (A3W, A3, B4, A4R, B5R, 12" x 18",
11" x 17", 8-1/2" x 14", 8-1/2" x 13",
8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 8K, 16KR)
Stapling*4:
100 sets or 1550 sheets (A4, B5, 8-1/2" x 11",
16K)
50 sets or 650 sheets (A3, B4, A4R, 11" x 17",
8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11"R, 8K)
Lower tray
Non-stapling*3:
2450 sheets (A4, B5, 8-1/2" x 11", 16K)
1700 sheets (A5R, 5-1/2" x 8-1/2"R)
650 sheets (A3W, A3, B4, A4R, B5R, 12" x 18",
11" x 17", 8-1/2" x 14", 8-1/2" x 13",
8-1/2" x 11"R, 7-1/4" x 10-1/2", 8K, 16KR)
Stapling*4:
100 sets or 1550 sheets (A4, B5, 8-1/2" x 11",
16K)
50 sets or 650 sheets (A3, B4, A4R, 11" x 17",
8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11"R, 8K)
Power supply Supplied from the machine
Dimensions 515 mm (W) x 645 mm (D) x 1100 mm (H) (20-9/32" (W) x 25-25/64" (D) x 43-19/64" (H))
Weight Approx. 43 kg(94.8 lbs.)
Overall dimensions when
attached to machine
1775 mm (W) x 715 mm (D) (69-55/64" (W) x 28-9/64" (D)) (When tray is extended)
Stapler section
Allowed paper sizes for
stapling
A3, B4, A4, A4R, B5, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 8K, 16K
(Three stapling positions: one staple at bottom left corner, one staple at top left corner, and two
staples.)
Maximum number of
sheets for stapling*4
50 sheets (A4, B5, 8-1/2" x 11", 16K)
30 sheets (A3, B4, A4R, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11"R, 8K)
(30 sheets when the sheets are the same width but different lengths.)

12
SPECIFICATIONS
Saddle stitch finisher specifications*1
*1 Paper pass unit (MX-PBX2) is required to connect the saddle stitch finisher to the machine.
*2 The maximum number of sheets that can be held varies depending on ambient conditions in the installation location, the type of
paper, and the storage conditions of the paper.
*3 Up to 100 sheets of non-standard size paper, envelopes, and transparency film (A4 (8-1/2" x 11")) can be loaded.
*4 The maximum number of sheets for stapling assumes a paper weight of 80 g/m2(21 lbs.) and includes two cover sheets of
106 g/m2to 256 g/m2(28 lbs. to 68 lbs.).
Model MX-FNX4
Paper sizes A3W, A3, B4, A4, A4R, B5, B5R, A5R, 12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11",
8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR
Paper weight
Thin paper (55 g /m
2
to 59 g /m
2
(15 lbs. to 16 lbs.)), plain paper (60 g /m
2
to 105 g /m
2
(16 lbs. to 28 lbs.)),
heavy paper (106 g /m
2
to 256 g /m
2
(28 lbs. to 68 lbs.)), envelopes (75 g /m
2
to 90 g /m
2
(20 lbs. to 24 lbs.))
Modes Non-staple, staple, saddle stitch
Allowed paper sizes for offset
A3, B4, A4, A4R, B5, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 8K, 16K
Offset distance 30 mm (1-3/16")
Tray
capacity*2
Upper tray
Non-stapling*3:
1550 sheets (A4, B5, A5R, 8-1/2" x 11",
5-1/2" x 8-1/2"R, 16K)
650 sheets (A3W, A3, B4, A4R, B5R, 12" x 18",
11" x 17", 8-1/2" x 14", 8-1/2" x 13",
8-1/2" x 11"R, 7-1/4" x 10-1/2", 8K, 16KR)
Stapling*4:
100 sets or 1550 sheets (A4, B5, 8-1/2" x 11",
16K)
50 sets or 650 sheets (A3, B4, A4R, 11" x 17",
8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11"R, 8K)
Lower tray
Non-stapling*3:
2450 sheets (A4, B5, 8-1/2" x 11", 16K)
1700 sheets (A5R, 5-1/2" x 8-1/2"R)
650 sheets (A3W, A3, B4, A4R, B5R, 12" x 18",
11" x 17", 8-1/2" x 14", 8-1/2" x 13",
8-1/2" x 11"R, 7-1/4" x 10-1/2", 8K, 16KR)
Stapling*4:
100 sets or 1550 sheets (A4, B5, 8-1/2" x 11",
16K)
50 sets or 650 sheets (A3, B4, A4R, 11" x 17",
8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11"R, 8K)
Power supply Supplied from the machine
Dimensions 625 mm (W) x 645 mm (D) x 1100 mm (H) (24-39/64" (W) x 25-25/64" (D) x 43-19/64" (H))
Weigh Approx. 74 kg(163.1 lbs.)
Overall dimensions when
attached to machine
1885 mm (W) x 715 mm (D) (74-3/16" (W) x 28-9/64" (D)) (When tray is extended)
Stapler section
Allowed paper sizes for
stapling
A3, B4, A4, A4R, B5, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 8K, 16K
(Three stapling positions: one staple at bottom left corner, one staple at top left corner, and two staples.)
Maximum number of
sheets for stapling*4
50 sheets (A4, B5, 8-1/2" x 11", 16K)
30 sheets (A3, B4, A4R, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11"R, 8K)
(30 sheets when the sheets are the same width but different lengths.)
Saddle stitch section
Stapling method Fold in half and staple in two places on centreline
Folding position Fold at centreline (can be adjusted with [Saddle Stitch Position Adjust] in the System Settings)
Allowed paper sizes for
saddle stitch stapling
A3, B4, A4R, 11" x 17", 8-1/2" x 14", 8-1/2" x 11"R, 8K
Allowed paper weights for
saddle stitch stapling
55 g/m2to 256 g/m2(15 lbs. to 68 lbs.)
Number sheets for saddle
stitch stapling / Number of sets
Maximum: 15 sheets (80 g/m2(21 lbs.) x 14 sheets + 256 g/m2(68 lbs.) x 1 sheet) / 10 sets (11 to
15 sheets), 20 sets (6 to 10 sheets), 25 sets (1 to 5 sheets)

13
SPECIFICATIONS
Punch module specifications (for finisher / saddle stitch finisher)
Model MX-PNX2A MX-PNX2B MX-PNX2C MX-PNX2D
Hole punching 2 holes 2 holes or 3 holes 4 holes 4 holes, broad width
Allowed paper sizes for
punching
A3, B4, A4, A4R, B5,
B5R, 11" x 17",
8-1/2" x 14",
8-1/2" x 13",
8-1/2" x 11",
8-1/2" x 11"R,
7-1/4" x 10-1/2", 8K,
16K, 16KR
2 holes:
8-1/2" x 14",
8-1/2" x 13",
8-1/2" x 11"R
3 holes:
A3, A4, 11" x 17",
8-1/2" x 11"
A3, A4, 11" x 17",
8-1/2" x 11"
A3, A4, 11" x 17",
8-1/2" x 11"
Punchable paper weights
55 g/m2to 256 g/m2(15 lbs. to 68 lbs.)
Power supply Supplied from finisher / saddle stitch finisher
Dimensions 115 mm (W) x 600 mm (D) x 995 mm (H) (4-17/32" (W) x 23-5/8" (D) x 39-11/64" (H))
Weight Approx. 8 kg(17.6 lbs.)
Note:
Special media such as transparency film and label sheets cannot be stapled or punched.

14
SPECIFICATIONS
Inserter specifications*
* Punch module (MX-PNX2A/B/C/D) is required to connect the inserter to the finisher (MX-FNX3).
Model MX-CFX1
Paper sizes A3W, A3, B4, A4, A4R, B5, B5R, A5R, 12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11",
8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR
Paper weight Thin paper (55 g/m2to 59 g/m2(15 lbs. to 16 lbs.)), plain paper (60 g/m2to 105 g/m2(16 lbs. to
28 lbs.)), heavy paper (106 g/m2to 256 g/m2(28 lbs. to 68 lbs.))
Paper capacity 100 sheets (80 g/m2(21 lbs.))
Paper types SHARP-recommended plain paper, recycled paper, coloured paper, heavy paper, thin paper, and
transparency film
Power supply Supplied from finisher / saddle stitch finisher
Dimensions 455 mm (W) x 595 mm (D) x 1050 mm (H) (17-59/64" (W) x 23-27/64" (D) x 41-21/64" (H))
Weight Approx. 23 kg(50.7 lbs.)

15
SPECIFICATIONS
Printer specifications
*1 When the PS3 expansion kit (MX-PKX1) is installed and the machine is used as a PostScript printer.
*2 Barcode font kit (AR-PF1) is required.
*3 Supported operating systems are Windows 2000 / XP.
*4 Supported operating systems are Windows 2000 / XP/ Vista.
Type Built-in
Continuous printing speed
Same as continuous copying speed (When printing same document continuously on A4
(8-1/2" x 11") plain paper in non-offset mode, excluding processing time.)
Printing resolution 600 x 600 dpi / 1200 x 600 dpi*1(greyscale printing)
Printer driver type PCL5c, PCL6, PostScript 3 compatible*1
Supported protocols TCP/IP, IPX/SPX, NetBEUI, EtherTalk
Supported client PC
operating systems
See "VERIFYING SYSTEM REQUIREMENTS" in the Software Setup Guide / Sharpdesk Installation
Manual
Fonts PCL5c, PCL6 80 European fonts, 28 barcode fonts*2, 1 bitmap font
PostScript 3 compatible*1136 European fonts
Interface port
MX-5500N/6200N/7000N
LAN connectivity: 10Base-T / 100Base-TX
USB connectivity: Supports USB 2.0 (Hi speed)*3
MX-6201N/7001N
LAN connectivity: 10Base-T / 100Base-TX
USB connectivity: Suports USB 2.0 (Hi speed)*4
Memory 896 MB (MX-5500N/6200N/7000N) / 1 GB (MX-6201N/7001N)
Print area Entire page excluding margin of 4.2 mm (11/64") at each edge. The actual print area may vary
depending on the printer driver and the software application.

16
SPECIFICATIONS
Network scanner / Internet Fax*1specifications
*1 Internet fax expansion kit (MX-FWX1) is required.
*2 Total number of all destinations (Scan to E-mail, Scan to FTP, Scan to Desktop, Scan to Network folder, Internet Fax, Fax, and
Group)
Pull scan function (TWAIN) specifications
Type Built-in
Scanning resolution (dpi)
100 x 100, 200 x 200, 300 x 300, 400 x 400, 600 x 600
Internet Fax: 200 x 100, 200 x 200, 200 x 400, 400 x 400, 600 x 600 (200 x 100, 200 x 200 when file
type is TIFF-S) Halftone can be selected for resolutions other than 200 x 100 dpi.
Scanning speed
Colour (A4 / 8-1/2" x 11")One-sided: 35 pages/min. (200 x 200 dpi),
Two-sided: 35 pages/min. (200 x 200 dpi)
Black and white (A4 / 8-1/2" x 11") One-sided: 65 pages/min. (200 x 200 dpi),
Two-sided: 65 pages/min. (200 x 200 dpi)
Interface port LAN connectivity: 10Base-T / 100Base-TX
Supported protocols MX-5500N/6200N/7000N : TCP/IP (IPv4)
MX-6201N/7001N : TCP/IP (IPv4, IPv6)
File formats
Colour
(including greyscale)
File types: TIFF, JPEG, PDF, Encrypted PDF
Compression ratio: High / Medium / Low
Black and white File types: TIFF, PDF, Encrypted PDF
Compression modes: None / Medium (G3) / High (G4)
Internet Fax
(black and white only)
File types: TIFF-FX (TIFF-F, TIFF-S)
Compression modes: Medium (G3) / High (G4)
Remarks
Number of one-touch keys for
storing destinations*2
Maximum number of keys: 999
Number of destinations that can be
stored in a group (1 key)*2
Maximum number of destinations in one group (1 key): 500
Scan destinations Scan to E-mail / Scan to FTP / Scan to Desktop / Scan to
Network Folder
Supported protocol TCP/IP
Supported client PC
operating systems
MX-5500N/6200N/7000N : Windows 98 / Me / 2000 / XP / Server 2003
MX-6201N/7001N : Windows 98 / Me / 2000 / XP / Server 2003 / Vista
Colour modes Full Colour, Greyscale, Mono Diffusion, Mono 2 gradation
Resolution settings
75 dpi, 100 dpi, 150 dpi, 200 dpi, 300 dpi, 400 dpi, 600 dpi
(The resolution can be specified by entering a numerical value from 50 to 9600 dpi. However, when
a high resolution is specified, it is necessary to reduce the scanning area.)
Scanning area Maximum: A3 (11" x 17")