Sharp BE-2520 User manual

ee
nie
Rede
:

Display unit:
1-3.
oA
SPECIFICATIONS
1-1. General”
Model name:
Power requirements:
Power consumption:
Operating
temperature:
Physical dimensions:
Weight:*.
Memory retention time:
Printer unit:
Roll paper: ©
Ink ribbon:
~ BE-2520 ©
AC220V 50Hz
38W
0°C ~ 40°C (32° ~ 104° F)
286{W)
x.
377
{D}:
x
135:
(H)
mm
Approx. 5 kg (14 Ibs.)
Approx. 1 month
-Ni-cad:rechargeable battery:
Fluorescent
display:
tube:
(green)
M-210V: 7x:F-dot matrix
Width:
76+£0.5
mm:
Max::0.D.:
80:mm
Width:..«;
13.
mm.-
Length:
10m
Color: .. Violet
Type: ERC-P03
1-2.
Reference
documents
@. -Cash:Reg
ister Basic: Manual
®
M-210V-Printer
Service
Manual
Display
PWB
internal construction
Printer
~ M-210V
Main PWB
Fig. 7
1-4. ‘Keyboard layout
e Standard
*Key top
layout sel
Keyboard Layout
layout may be changed. At the sam
ect presetting (MRS1) is required.
BE=2520
The
keys
have
the
following
functions.
(1)
[0]—[9],
[00],
[060}
(Numeric
keys)
@ Used to enter data:
@ Two key roll-over function:
®
Maximum
10
digit
input
capacity.
(Except ACCT #— up to 11 digits)
(2) [ CLEAR] (Clear key)
The clear key is used as follows:
@ To clear an incorrect numeric input.
Used
to
clear
an
entry
overflow
error
(too
many
digits
entered).
Used
to
clear
an
overflow
error
of
totalizers
caused
by
an
entry
from
the
or
[=]
key.
This
causes
“CLEAR”
to
be
printed
on
the
journal
tape.
Used
to
clear
an
overflow:
error
of
totalizers,
causing
“OVF
CLEAR”
to
be
printed
on
the
journal
tape.
Used
to
clear
the
machine
lock
state’
that
is
en-
countered
if
the
balance
is
negative
in
“LIST”
mode.
Depression
of
this
key
prints
“BAL
(—)
CL”
on
the
journal
tape.
Used to terminated the “LIST” mode.
lf
the
“LIST’mode.is
terminated,
“LIST
CLEAR”
is
printed
the
journal
tape.
This
key
cannot
terminate
the
“LIST”
mode
during
an
entry,
however.
however.

BE=2520
@ Used for cancellation of the LIST mode:
Message is printed in this case. _
. CLEAR key
YES
|
; | = LIST mode?
LIST mode clear
LIST mode clear
message print
2) (DEPOSIT, (CASHIN), [CASHOUT], [CAST CHECK)
[MISC1], [MISC2], [MISC3], and [MISC4].
(Standard 8 items summary) Validation function keys
When any of these validation function keys is depressed
after entering data by the numeric keys, the data is
stored in the specific grand totalizer-and printed on the
slip. The data is further added to the batch totalizer
only when this is designated by presetting in advance.
The consecutive number is counted up as a result of the
depression of any of these (function) keys: However,
this is determined by the presetting done in advance.
During resetting (Z mode), the net total is printed with a
“4 “_" or with a “’non-add” symbol! (specified by the
presetting).:
(CASH IN TOTAL) — (CASH-OUT TOTAL) —
‘CHECK TOTAL) = NET TOTAL
For functions programmed for auto check function
“Yes,” registered data are sequentially stored in the auto
check buffer.
Storing registration data in the auto check buffer is
possible up to lock out point which may be peor at the
Initial presetting.
(CASH
The balance memory is updated by the data registered
in the LIST mode, according to “+, ““—’’, or “NON-
ADD” sign given to that validation function key at the
time of initialization.
(4) [DUP] (Duplicate: key,
@ When the duplicate key is pushed oe ipialy after any
- of the function keys (DEPOSIT, CASH-IN, etc.) has
been used, the identical contents of the transaction can
be printed on a slip.
The
duplicate
key
can
be
aperated
repeatedly,
a
as
many.
times
as
has
been.preset:.
r
If
a
duplicate
key
has
been
programmed
ceeenional
during
initialization,
a
next
operation
is
not
perraittect
unless
the
specific
key
has.
been
operated:
:
en
8A
Note:
{n=this:case
REWER,
the
consecutive
No.
is
not
counted
up»
(5) (ACCT. #] Lacan: rethaber kei
@ Used as an account number°key. Depression of the key
displays “Hon the 13th digit of the display and the
data on display at that time are then printed -on the
journal.
Number entry’ 6f account uwnibee is up to 11-digits
maximum. ,
Memory is not affected by the use of this key. :
If the machine is programmed for compulsive depression
of
the
[ACCT]
#
key
by
the
initial
setting,
it
does
not
allow any registration before this key’ is pressed. (REG
mode alone)
The conditional requirement for the: depression of the
key is cleared after a validation key depres-
sion,
key
depression,
or
mode
switch changeover.
For setting teller number (in “PGM’”’ mode).
For setting one-cycle or double-cycle printing in preset
“mode.
Inputting characters (symbols) that identify customer
ID in preset mode.
To read all preset programmed conditions {in ’Z" mode).
Used to set the print format. (Z mode) 7
Used to display the date and time. (BTL mode}
(6) [+], [=] (Pius, minus keys)
Used to carry out addition and/or subtraction after a
numerical input, the result ‘of which will be stored in-
the buffer memory.
The numerical data, input by either. of these keys, will
by printed on the journal paper with either a plus or
minus sign. The same data will also appear on the dis-
play.
The ‘results of the ealadletions will be cleared by
depression of [TOTAL] key.
When. the.results are to be registered by a validation
funétion key. The [REP] key is used together with the
or [TOTAL] key. in the following manner:
id + validation function key.
[FOTAL > > REP) > validation function key.
The results of the calculations are also cleared when the
mode switch is changed. ©’
Zero or negative result can be registered by the use of
the [SUB TOTAL], [TOTAL], or [REP] key.
(7) [SUB TOTAL] key
®@ When the SUB TOTAL key is depressed (after operation
of the plus/minus keys), the resulting information. will
be printed and displayed but not cleared.

a
@
Operation
of
the
plus/minus
‘keys
can
continue
even
after.
the[SUB.
TOTAL
key
has
been
depressed.
When
the
(SUB
TOTAL]
key
is
depressed,
the
resulting
,
information
can
be
registered
in
the
following
manner:
“SUB
TOTAL”
>
“REP”
>
VALIDATION
FUNCTION
KEY.
:
Used
to
display
&
print
the
accumulation
of
calculations
registered
with
the
+
or
—
keys.
if
the
result
of
a
calculation
is
positive,
the
indicator
“+
lights,
and
if
negative
the
indicator
“”
—
"
will
light.
It
is
possible
to
continue
computation
with
+
or
—
keys
after
depressing
the
key.
@) [TOTAL] key
When
the[TOTAL]
key
is
depressed
(after
operation
of
the.
plus/minus..or-[SUB_TOTAL]
keys),
the
resulting
information
will
be
printed,
displayed
and
cleared
from
mernory.
—
To
use
the
total
amount
with
the
validation
keys
use
the
[REP|
key
as
follows:
“TOTAL”
>
“REP”
>
VALIDATION
FUNCTION
KEY
(9)
[REP]
(Repeat
key)
@
This
key
is
uséd
to
register
another
transaction
by
using
the
value’
being
displayed
obtained
by
the
depression
of
a
validation
function
key,
[DUP
key,
[SUB
TOTAL
key
or
the[TOTAL
key.
For
repetition
of
addtion
or
subtraction
of
a
displayed
amount.
=.
“This
‘key
is*used’
to
enter
a
displayed
value
with
a
valida-
tion’
function:
key
after
the
depression
of
the
(suB
TOTAL] or [TOTAL] key.
This
key
is
used
to
‘carry
out
other
transactioris
by
use
of
other
validation
function’
keys
utilizing
a
displayed
value
after
depression
of
a
validation
function
key
of
duplication through the [DUP] key.
This
key
is
used
to
set
the
time.
(PGM
mode)
(10)
[R/TTL]
(Read
total
key)
This
key
is
used
to
read
and/or
reset
batch
and
Grand
totals
with
depression
of
this
key.
@
The
batch
totals
are
read
without
resetting
{in
“PGM”
mode)
.
e
Batch
totals
are
printed
and
reset
(in
“BTL”
mode)
@
Grand
totals
are
printed
and
reset
(in
““Z’’
mode)
This
key
can
also
be
used
to
read
or
reset
the
contents
of
the
check
buffer
memories,
For
this
purpose
enter
“1”
and then depress this key.
@
The
above
operation
reads
the
contents
of.
the
check
buffer
memories
(in
“R
EG”
tnode)
®@
The
above
operation
prints
and
resets
the
contents
of
the
check.
buffer
memories
{in
“Z”
mode)
@
Use
of
the
R/TTL
Rey
is
prohibited
in
ae
LIST
mode.
(Z
mode)
(11) (Read net key)
@
For
computing
net
total
of
daliy
transactions.
The
net
total
appears
on
the
display
and
prints
on
the
journal.
@
For
computing
the
check
buffer
total,
enter
.‘’1”
and
depress
this
key.
The
check
buffer
total
appears
on
the
display
and
prints
on
the
journal
(“REG”
mode)
4
BE=2520
@
For
computing
net
batch
total
(in.
“PGM“mode).
The
total
shows
up
on
the
display
and
prints
on
the
journal.
©
Use
of
the
key
is
prohibited
in
the
LIST
mode.
(42)
[P/F]
(Paper
feed
key)
@
There
are
two
kinds
of
paper
feed
available,
a
fast
paper
feed
and
anormal
paper
feed.
Depressing
this
key
once
will
cause
paper
to
feed
{normal)
at
one
line
per:
printer.
cycle
(2.
4
lines/second).
Depressing
and
holding
this
key
down
will
cause
paper/
feed
(for
the
first
three
lines)
at
a
rate
of
one
line
per
printer
cycle,
but
then.
changes
speed
to
the
fast
paper
_
feed
which
is
about
three
lines
per
printer
cycle
(7.2
line/second).
(13) [LIST] key
1, Used to assign the LIST mode.:
Depression
of
this
key
makes
the
LIST
mode
Sperational:
with
the.
LIST
mode-message
on
the
display
and
print-
out.
2.
In
the
LIST
mode,
the
balance
memory
is
updated
with
the
amount
registered
according
to
the
sign
("+',"—",
or
NON-
ADD)
given
to
the
validation
function
key.
Register
operation
in
the
LIST
mode
is
the
same
as
in
normal
operation,
including
validation
printout
format
and
accumulator
update...
ccarare
ear
Bal
.
The
LIST
mode
is
cancelled
by
the
key.
When
the
LIST
mode
is
cancelled,
not
ee
the
message
is
printed
on
the
journal,
but
also
the
eats
Seely
‘is
cleared.
.
The
capacity
of
the
balance
memory
is
10
digits
tnclud-
ing
a
sign,
any
entry
excéeding
‘this:
limit
is
prohibited.
5.
Reading
and
resetting
in
the
LIST
mode.
is
prohibited.
(14) [BAC] key (Balance key)
1.
This
key
is
used
to
display
the
balance
in
the
LIST
mode
and to perform validation print.
Depression
of
this
key
clears
the
balance.
memory
and
the LIST mode i is cancelled.
.
If
the
balance
is
negative,
the
machine
performs.
valida-
tion
printing,
encounters
the
“balance.
negative
_
error,
and
enters
the
machine
lock
state.
To
release
from
this
condition,
it
needs
to
press
the
[CLEAR]
key,
which
causes
the
LIST
mode
also.
cancelled.
i
Accumulators
are
not
affected
by
the
depression
of
the
[BAL]key.
The
consecutive
numbering
is
not
incremented,
neither.
This
key
is
used
to
activate
the
clock
function
("Z"
mode).
This
key
is
used
to
clear
the
data
holding
an
account
#.
2.
4.
5.
6.

BE=2520
1-5. Key switches
Switch layout
|. Mode switch
Power switch
@ Power Switch
1
@ Used to turn machine on or off
Note: There are about 300 different keys available
for this machine.
6. Mode control switch
(1) REG mode
Originary transactions are possible.
Reading the grand totalizer —
_ When. the key is depressed in this mode, the
details. of the grand totalizer are printed, but are not
cleared. from memory: : #
Auto check reading
After pressing the numeral key [1] , when the
key is pressed, the details of the check buffer totalizer
are printed out, but its contents are not cleared.
(If the machine is programmed for auto check function
“No”, it does not allow auto er reading.)
(2) PGM mode
® Setting of teller No.
Teller No.
-», [3 digits, ....
The
teller
No.
can
‘be
set
by
entry
a
3
digit
(or
less)
number,
then,
depress
[ACCT
#
[ACCT
#
|
key.
©
A
different
machine
number
can
be
assigned
during
initialization,
(Refer
to
MRS7)
in
section
3.
initial
presetting.
@ Readingthe batch totalizer _
When the [R/TTL] key is depressed in thie mode, the
details of the batch totalizer are printed, but are not
cleared from memory.
®@ Setting of date
The date (month, day, year) can be set by entering a
6-digit number (5-digits in the case of a 1-digit month)
then depress the key.
Year
2-digits
Month
2-digits
_Deseription Ot Allowed X Not allowed
Note:
“Mode Key No.: 6210
: “Remarks : :
. Insertion
‘& removal
of key
Teller keys are common.
Master keys are common.
Ansertion
& removal
Power switch key are
manufactured in. about
300 different kinds.
®@ Setting of time
When the calender timer function is initialized the date -
entry format is different according. to. the setting code 1
through 7. For details of the proper..entry procedure,
refer to MRS-16 in section 3, Initial Presetting. If the
entry has been correct the date is printed on the journal
and displayed on the display.
Enter the hour (one or two digits)..and minute (two
digits) in this sequence, then press the [REP | key.
Example: Setting the time at 9:45 am.:
PGM
04,
12.
85
09-45
When
the
AM/PM
system
is
selected,
aN!
of
EPH
is
displayed.
Set
the
time
on
the
Militaly
system.
When
setting
the
time
at
9:45
pm,
enter
“2145”.
if the time. is correctly entered, it is displayed along
with the date. —
Print on the journal.
94S 9OLBS. ..
015

The
current
time
is
entered
by
entering
two
digits
for
the
hour
and
two
digits
for
the
minute
(three
digits
total,
if
the
hour
digit
is
a
single
digit)
and
depressing
the
key.
Please
note
that
the
24
hour
military
system
must
be
used
for
entry.
,
When
the
calender
timer
function
has
been
programmed
_
inactive
during
initial
presetting,
this
operation
is
pro-
hibited.
if
the
correct
entry
is
made
the
time
will
be
printed
on
the
journal,
as
well
as
being
displayed
on
the
display
along
with
the
date.
This
display
will
bé-cleared
upon
the
next
depression
of
an
effective
key
or
the
mode
switch
position
is
changed.
Hour
2 digits
Time
2 digits
Display
configuration
of
date
and
time
display
13 12 11 10
6 5 4 3 2 1
In the case of AM/PM
system
This
display
will
be
cleared
upon
depression
of
a
next
effective
key
or
changing
of
the
MODE
switch
location.
(3)
BTL
(batch
total)
mode
Reading
and
resetting
of
batch
totalizer
when
the
R/TTL]
key
is
depressed
in
this
mode,
the
details
of
the
batch
totalizer
are
printed
twice
(same
format)
and
are
reset
(cleared
from
memory).
When
a
validation
function
key*
(DEPOSIT,
CASH
OUT,
CASH
IN,
CASH
CHECK)
is
depressed
in
this
mode,
the
contents
in
the
batch
totalizer
for
that
function
key
(i.e.
DEPOSIT)
aré
printed,
displayed
and
cleared
from
memory.
*MISC1-MISC4
are
also
validation
function
keys.
(4)
Z
(resetting)
mode
Reading
and
resetting
of
grand
totalizer
when
the
key
ig
depressed
in
this
mode,
the
details
of
the
grand
totalizer
are
printed
twice
(same
format)
and
are
resét'(cleared
from
memory).
Presetting
(pre-programming)
the
machine
operation
is
accomplished
in
the
Z
mode
(master
reset
mode).
When
the
key
is
depressed,
the
preset
pro-
gram
is
printed
out.
i
Special
cancellation
.
A
transaction
in
the
“REG”
mode
can
be
cancelled
out
y
registering
the
same
transaction
in
the
Z
mode
in
this
case,
the
print
format
will
be
different.
"But,
the
list
memory
is
updated
in
a
normal
manner.
Instead
of
having
a
$“
as
our
zero
supression
symbol,
a
“C”
(position
11)
and
““—”
will
be
printed
out.
BE-2520
Print format
HOQOC
o..,
eeees
«eee
9.99
<—
Print
Format
1
.
#999C
...
noe
cose
3
09.99
<
Print
Format
y)
or
3
Auto
check
resetting
.
After
pressing
the
numeral
key
“1”,
when
the
“R/TTL”
key
is
pressed,
the
details
of
the
auto
check
totalizer
are
’
printed
out
once,
and
its
contents
are
all
cleared.
(If
the
machine
is
programmed
for
auto
check,
function
“No”,
it
does
not
allow
auto
check
resetting.).
List
mode
Used
for
cancellation
of
the
LIST
mode.
Message:
is
printed
in
this
case.
1-7. Display
13
Vv
OSSEEEEEEEE
OVF
:
PGM
BTL
Fluorescent display tube (green)
Fig. 5
Column
No.
Lights up in Z mode.
Notes
Lights. up in batch mode.
Lights up in program mode.
8 Lights up when result of addition and
subtraction becomes nagative.
Lights up when the balance memory is
negative when the kéy is depressed.
10 Lights up when result of addition and
+ subtraction becomes positive.
Lights up when the balance memory is.
positive when the key is depressed.
Lights
up
in
the
event
of
an
overflow
error
in
the
memory
(secondary
-totalizer)
Lights
up
when
numerical
input
exceeds
11
digits.
Lights.up when primary totalizer is in an.
overflow error.
Lights up when an error is made in an
| operation. ‘
Lights
up
when
the
stip
is
Rot
inserted,
when
the
slip
detect
function
has
been
programmed
active.
Fe
2
bar
PE
TES
® Light up, if the machine is programmed
for auto check function ‘“Yes,” when
the number of stored items becomes
larger than the warning point
programmed.at initial setting.
(The
“slip
:not
inserted”
error
has
priority.)
®
Goes
off
when
the
auto
check
resetting.
©
Goes
off-when
a
correction
is
made
by
special
canellation-and
the
stored
items
goes less than the warning point
Programmed at initial setting.
H
13
e
Lights
up,
if
the
machine
is
programmed
for
sentinel
amount
“Yes,”
when
the
grand
totalizer
net
is
equal
to
or
larger
than
the
sentinel
amount.
:
© Goes off with resetting of the. grand
totalizer. Se
© Goes off when a correction is. made. by
special cancellation and the grand
totalizer
net
goes
less
than
the
sentinel
amount. reyes
Lights
up
when
the
account.
number
reten-
tion
function
has
been
programmed.
i
Light
goes
out
when
the
account
number
is
cleared.
a
LS
© Becomes active in the LIST Mode.
@ Goes out after the cancellation of the
LIST mode and by the depression of the ©
BAL key. In the case of the negative
balance error, the indicator goes out after
cancellation of the error condition.

BE-2520
1-8. Buzzer function
In
the
event
of
mis-operation
or
overflow
error,
the
buzzer
will
sound.
The
relationsip
between
the
status
display
(
vi).
and buzzer is shown below.
Tm
lel
[a
¥
|
icperetion
[TTF
Tore
sot
[Operate
conecty
[
2.
|
Numerical
input
overflow
||
|_|
|
|
__|Shore
buzzer]
Press
CLEAR
key.
Overflow
of
primary
totalizer
[|
©
[|
|__|
|
Short
buezer
|
Press
CLEAR
key.
|
"s.—_|
Slip
not
inserted
;
i
eS
Number of used auto check a
buffers<warning point ;
net’ é :
| Negative balance error ae a ae O } Short buzzer
NOTE: Priority of the error state is as follows. 1:4,2:F1, 3:1, 4:£ ‘ore
Insert slip,
© Perform auto check resetting
e Number of used auto check
buffers<warning point
© Grand totalizer resetting
© Make the sentinel amount larger
than the grand totalizer net.
Depression of the CLEAR. key
1-9,
Printer
1-10.
Slip
printout
® Printer specifications
35_% 83 32 81 9 20 28 27 26 % M28 22 2) 2 19 18 17:18:15 14 18 12 12 10 9 876548 21°
Item
Standard
(
B
Type
M-210V
©
9
99ABCDZ9~99-99#999$8$$.8$$.989.99(8¥)
Say
;
,
noes
amen
nt
me
Nt
a
Printing
method
Seria!
dot
matrix
(agar
(aI)
Month
—
Day
Year
SOnsBEutivé
No.
Aone
Symbol
35 digits
7 x 7 (7 wires) dot matrix
Number of digits
(Print format 1)
Character dimensions
Line pitch 4.23mm+10% —
Digit pitch Approx. 1.9 mm
Printing speed | Approx, 2.4 tines/second —
$: zero suppression symbol
Note
1:
When
the
consecutive
number
is
in
4
digits,
a
number
is
printed
in
place
of
the
“#’
mark,
When
DUP
key
is
used,
slash
marks
(/)
are
printed
be-
tween
month
day
and
day
year
insteard
of
(—)
marks.
The
consecutive
number
automatically
returns
to
Printer dimensions __ 123(W) x 293(D) x 153(H) mm
Journal paper roll size 76 +0.5 mm wide x 80 mm OD
Thickness of journal paper! 0.07 to 0.09 mm
Peet,
Width:
more
than130mm_.
,
Fi
Maliderlen
pepe
Thickness:
0.09
to
0.18
mm
zero
(from
9999
to
0000).
ERC-PO3
Note
2:
The
zero
suppression
symbol
“$’
is
a
floating
Color:
violet
;
symbol,
and
is
printed
only
once
in
the
highest
Material:
nylon
size
,
.
.
Size:
13
mm
wide
by
10
m
long
digit
of
the
amount.
MCBF: 2 million tines
Note
3:
“+”
or
“—B”
is
printed
in
the
place.
of
.a
sign,
sfonde
;
When
the
balance
is
printed.
1-11.
Print
format
under
reading
mode
:
(for standard feature)
BATCH
TOTAL
CHECK
BRANT
TOTAL
CHECK
(11
S41
91785
ocadx
iu
210
91785.
_0000X.
OX
ft
6.00
0
OX
ft
0.00
0.
aOxco
G.0cca
Oxca
0.0000
OXCI
0.0001
OXCI
0.0001
DXGBees
ener
oe
aes
«
0.00cc
ss
OXCE.
0.000.
OXML
:
0.00M1
OXML
0.00ML
OXM2
0.002
OXM?
0.0082.
OXM3
0.00M3
a.
8
OXM3..
0.003
DXM4
0.0064
a
OXM4
-
0,00¢4
-0. GOT . -0,00NT |
+0.GONT = +0. 00NT

BE-2520
111:
Teller/machine
number
D,
CO,
Cl,
CC,
91785:
Date
M1,M2,M3,M4:
Validation
function
keys
211:
TIME
NT:
Net
total
ooo0ox
Reading,
number
0
X:
Reading.
mode
(PGM
or
REG.)
1-12. Print format-under resetting mode
(for standard feature)
BATCH TOTAL CLEAR GRAND TOTAL CLEAR
iil. i082 91865 oco2z {11 214 91785 H001Z
o7 oi 0.00 0 oz 0 0.00 0
ozcg 0.00C0 0700 0.00C0
0ZCI 0.00CI ; OZCI * .0,.00C1
ozcc
0.00CC
0200
.
0.00CC
0741 0.06Mi : OZM1 0.0041
OZNe 0.002 OZHe 0.002
OZH3 0.00M3 OZM3 0.00K3
o2ZM4
0.004
0ZM4
0.0044
~0. OOMT -0.00MT
+0. OGNT ; +0.Q0NT
BTL mode Z mode
Note: The print formats for the batch and grand totals are
7 printed twice (2X) under the resetting modes.
0018Z: Reset, number 18
0020Z: Reset, number 20
Calculation of the net total is determined by the pre-
setting of the machine.
The reset counter is attached independently to the
grand totalizer and batch totalizer. This counter auto-
matically returns to zero (from 9999 to 0000).
(1
—
(2
~—
(3
—_—
In the case of resetting, the first details. are printed on
the journal, the paper is feed 4 lines, and then the
same format is printed again (on journal printing
only). ;
(4
~
When resetting or reading the batch total, the items of
which accumulation into the totalizer is not set by the
initial setting are skipped, and not printed.
_ The net total is not printed if there is an item in which
accumulation is not specified but ‘+’ or ‘‘—” sign is
set.
Four
items
are
printed
when
the
four item
mode
was
designated at the time of initialization.
(5
pases

BE=2520
1-13. Auto check reading and resetting mode (Slip print)
8
4
88
2
31
9
DB
Bw
BH
MW
8
2
210
19
BW
6
1 4
13 12
110
9
8
7
6
5
4
8B
2
1
(MONTH) (DAY) (YEAR)
NNN NNNNAN N NN NNN NN
WOww OO OO ~-e
NN NN NN NN NWN NN N NN WN NN NN NN NN NNN NN NN AN Z Zz ’
oo i Gr Ce) OAH
+ + + co
HAHAH HHHOE
Z
~~
+N NNANANA
oO =
L
“~~
wv tL
+FTNNNNNANRN
Oo OWW WO OH OO ~—- ©
+
~ L ~ L
Z: Zero suppression
"a"
or
tet,
A
single
plus
or
minus
sign
is
printed
imme-
’ diately before the most significant digit of the amount
"7".
A
reset
sign.
In
the
case
of
reading,
“X”
is
printed.
"SY": Printed according to the initial setup.
Relation.
with
key
is
DEPOSIT,
CASH
OUT,
CASH
IN,
_.
CASH
CHECK,
MISC1,
MISC2,
MISC3,
and
MISC4
from
top.
"NT": NET TOTAL ho?
“MT:
A
minus
total
sign.
It
is
disregarded
and
not
printed
when
no
negative
sign
V/F
key
has
not
been
assigned
at
the
time of initialization.
(1) Net total is computed according to the sigh set the
validation function key at the time of initialization.
(2) The reset counter has two totals of grand and batch
which operated in the ring method.
(9999 > 0000)
@ Slip printing position
* (spare) ‘ 82 *
More than 199 ____+—__+|
unit: mm
*The position of validation sensor
—

BE=2520
‘4-14. Various print formats
Print Format 1_
Operator
no.
;
2
—
te
Validation
~~
5
:
nate
in
oe
we
:
|
timer”
|
999A8COZ9-99-95%909
$$
-SSS
-SS9.
99
(sy)
Print format
So K ~ yw tee +tt+ ttt
999ABCDZ9-99-99 NeW) eee) Cite) 9 - 9 ONT
ae
ye ae tee oot
kee *
/ *
. - 2227 27ZZLZLZZI#
xk *
e 999ABCDZ9-99-99#999C--~-----= 9.99 (sy)
[x [eeeaveozeyeoveoveonoes ses ten ovay
fe [eesavcoreceecteveen@ ew
x* x * :
SC
lit im 999ABCDZ9-99-99#9998$$ ,$$$ $9,998 |
tke
eee
ACCT#
CLEAR
e
999ABCDZ9/99/99#OD9NDY~~—--~~~—-- 9.99 (SY)
BAL(—) CL #2 ;
= Af eae