◆Name of each part ◆Instructions on use
◆Care
•If the film surface becomes dirty, soak a soft cloth such as a tissue or eyeglass cloth with commercially available rubbing alcohol (excluding
gel type) or diluted neutral detergent, and wipe it gently. If unevenness remains after wiping, wipe it gently with a tissue soaked in water
and wrung well. There is concave and convex processing on the film. If you rub it violently, the unevenness is broken and the function may
deteriorate.
◆Purpose of use
•This product is to reduces the contact of liquid droplets and dust to the face. Do not use it as a protective device against
solids or fire.
◆Precautions for use
•It cannot be used in places where harmful dust or gas is generated, or for the purpose of preventing them.
•Discontinue use if you have an abnormality on your skin or if it does not fit your skin.
•If you feel sick while wearing it, discontinue use.
•If you feel that your head is tight, adjust the mounting position or insert some material like a cushion.
•Please keep out of reach of infants.
•Do not use or store near fire.
•Store this product away from high temperatures and humidity and places exposed to direct sunlight.
•When disposing of this product, please dispose of it in accordance with the regulations of the local government.
◆Safety precautions *Please observe the following precautions
■The danger and its extent if the product is handled improperly.
Warning May cause death or serious injury
Caution Risk of minor injury or property damage
■The meanings of the graphic symbols used in the text.
Indicates that you must not do
Indicates that you should do
Warning To prevent injury Caution To prevent injury
⚫If it is damaged, never use it.
⚫Do not clean with benzene, thinner, kerosene, acidic detergent, alkaline
detergent, etc.
⚫Do not use in situations where there is a high risk of this product will fall off.
⚫Never disassemble or modify the main body or accessories.
⚫Do not use it only by children or within reach of infants.
⚫Do not use for purposes other than those described in this manual.
⚫Do not use while driving a car / motorcycle or bicycle.
⚫Be careful when handling the film in a way that the edges of the film
do not hurt your hands or face.
⚫Not use if the film is dirty or damaged.
⚫Install the film and frame correctly according to the instructions in th
manual.
⚫Discontinue use if you have an abnormality on your skin or if it does
not fit your skin
*** (subsidiary name and contact information)
Customer support：
claw
projection
hook
SHARP LOGO
Frame
hole
Projecting mark
□Film takeout
You can prevent fingerprints from
adhering to the film by taking out only the
top of the film with holes and attaching
the film to the frame
Upper: shallow
Lower: deep
Two holes are provided so that the angle of
the film when the face shield is attached
can be changed in two steps. it becomes
shallow to Insert the claws of the frame
into the upper hole, and it becomes deep
to Insert the claws of the frame into the
pilot holes
【Preparation 】
•Set the projecting mark on the film towards SHARP logo side on the frame.
【Procedure 】
１．Insert the claws of the frame in the order of holes ①→ holes ②on the film side.
２．Fit the protrusions of the frame into the two holes ③and ④in the center of the film.
【Wearing 】
•Lightly spread the handle of the frame and attach it to your head.
•Secure the frame on your forehead.
•If it is loose, pass a commercially available elastic cord through the hook of the frame and
tighten it.
□Film angle switching hole
□Removing
claw
hook
Film
hole hole hole
①②
③④
□Fitting
１．Remove the two holes ③④ in
the center of the film from the
protrusions on the frame.
２． Remove the holes on the film
side in the order of ②→ ①from
the claws on the frame.
Deep
Shallow
projection
Projecting mark
SHARP LOGO
