Sharp CD-MPX100E User manual

1 Accessories
MODEL
CD-MPX100E
MINI COMPONENT SYSTEM
TINSEA092AWZZ
05D R AS 1
Remote control × 1FM/AM loop aerial × 1
This Quick Start Guide will help you to correctly install and
operate your system.
2 Remote control battery installation
3 System connections
Wall socket
(AC 230 - 240 V, 50 Hz)
Left speakerRight speaker
AM loop aerial
FM aerial
Use 2 “AA” size batteries (UM/SUM-3, R6, HP-7 or similar).
Batteries are not included.
1Open the battery cover.
2Insert the batteries as shown.
3Close the cover.
The first time the unit is plugged in, the unit will
enter the demonstration mode. You will see words
scroll.
1Press the X-BASS/DEMO button to cancel the dem-
onstration mode.
2Press the ON/STAND-BY button to turn the power
on.
4 Turn on your system
Red
Black
XL-MPX100E_QG 15/03/2005, 11:09 am1

Listening to a CD or MP3/WMA diisc Listening to a cassette tape
1Press the ON/STAND-BY button to turn the power on.
2Press the CD button.
3Press the OPEN/CLOSE button to open the disc tray.
4Place the disc on the disc tray, label side up.
When loading a third disc, press the DISC SKIP button to turn the
disc tray, then place the disc in the open position.
5Press the OPEN/CLOSE button to close the disc tray.
6To select the disc you want to listen to first, press one of the
1- 3 buttons on the remote control.
7Press the / button to start playback.
12 cm (5”) 8 cm (3”)
1Press the ON/STAND-BY button to turn the power on.
2Open the cassette compart-
ment by pushing the area
marked “”.
3Load a cassette into the
TAPE 1 compartment or
TAPE 2 compartment with
the side to be played facing
towards you.
4Press the tape (1 2) button to select the cassette you want to
listen to.
5Press the / button to start
playback.
TAPE 1 TAPE 2
Listening to the radio
MINI COMPONENT SYSTEM CD-MPX100W
DISPLAY
1Press the ON/STAND-BY button to turn the power on.
2Press the TUNER (BAND) button repeatedly to select the desired
frequency band (FM or AM).
3Press the TUNING ( or ) button to tune in to the desired station.
When the TUNING button is pressed for more than 0.5 seconds,
scanning will start automatically and the tuner will stop at the first
receivable broadcast station.
To receive an FM stereo transmission:
Press the TUNER (BAND) button to display the “ST”indicator.
●“”will appear when an FM broadcast is in stereo.
Tape play indicator
FM stereo receiving indicator
FM stereo mode indicator
■If trouble occurs
When this product is subjected to strong external interference (mechanical
shock, excessive static electricity, abnormal supply voltage due to
lightning, etc) or if it is operated incorrectly, it may malfunction.
If such a problem occurs, do the following:
1. Set the unit to the stand-by mode and turn the power on again.
2. If the unit is not restored in the previous operation, unplug and
plug in the unit, and then turn the power on.
Note:
If neither operation above restores the unit, clear all the memory by
resetting it.
■Clearing all the memory (reset)
1. Press the ON/STAND-BY button to enter the power stand-by
mode.
2. Whilst pressing down the PRESET button and the
X-BASS/DEMO button, press the REC PAUSE button until“CLEAR
AL”appears.
Caution:
This operation will erase all data stored in memory including clock, timer
settings, tuner preset, and CD programme.
■Maintenance
Routine maintenance is required for continued optimum
performance, refer to the operation manual.
XL-MPX100E_QG 15/03/2005, 11:09 am2