Sharper Image 1014342 User manual

Sharper Image®name and logo are registered trademarks. Distributed by
and © 2022 MerchSource, LLC. Irvine, CA 92618. All rights reserved.
Distributed by MerchSource, LLC, Irvine, CA 92618.
For technical support, please visit www.merchsource.com or call
1-800-374-2744.
The artwork and design of this manual are protected by US copyright law
and may not be reproduced, distributed, displayed, published or used for
any purpose without prior written permission. It is not permitted to alter,
remove or reproduce any trademarks or copyright notice from this manual.
Printed in China.
Fly+Drive Drone — 5-inch
KEEP THIS INSTRUCTION MANUAL AS IT CONTAINS IMPORTANT
INFORMATION FOR FUTURE REFERENCE.
Due to continuous product improvements, the picture on the manual may
differ slightly from the actual product.
PATENT PENDING
Model Number: 1014342
CUSTOMER SUPPORT
[phone]
Before calling please locate the 10-digit
code printed on the back of your remote
QUESTIONS OR CONCERNS?
PLEASE GIVE US A CALL ... WE’RE HERE TO HELP
1. PREPARE FOR FLIGHT
• Drone must be charged before each use (Cable included)
• Indicator light will turn off once fully charged
• Install batteries in remote
2. PAIR YOUR DRONE
Before each flight pair the remote with the drone:
1. Turn your drone on and place on a flat, level surface
2. Turn on the remote on and move the left joystick up, then down
3. The beep will indicate successful pairing
4. Repeat steps 1 and 2 if necessary
3. REMOTE CONTROL OVERVIEW
Practice flying your drone below 10 feet and at low speeds until comfortable with all controls to
avoid unnecessary damage or injury
• Left joystick: left/right controls spin and Up/Down controls elevation
• Right joystick: controls flight direction
• Direction Trim: use to eliminate drift
To cut power to drone, move left joystick to down position
Getting to Know Your Drone
PLEASE READ ALL WARNINGS AND
INSTRUCTIONS PRIOR TO USE. KEEP THIS
DOCUMENT AS IT CONTAINS IMPORTANT
INFORMATION ABOUT YOUR DRONE.
14+
ADULT ASSEMBLY, CHARGING, AND
BATTERY INSTALLATION IS REQUIRED.
ADULT SUPERVISION IS REQUIRED.
ALIGN
LAND
SPIN TRIM
B
F
L R

iPrinted in China.
INTRODUCTION
Congratulations on your purchase of the
Rechargeable 2.4 GHz Fly+Drive Drone.
Get ready to soar to new heights. Master
the art of drone flying with remote control
maneuverability. This lightweight drone
will provide hours of fun.
SPECIFICATIONS
Drone Battery: 800 mAh Li-po
Remote Controller Battery: 4 x 1.5V “AA”
Charging Time: 120 minutes
Maximum Recommended Altitude: 100 ft.
TABLE OF CONTENTS
General Warnings Page 1
Contents, Remote Battery Installation, Battery Warnings Page 2
Charging LiPo Battery and Replacing Propellers Page 3
Remote Overview Page 4
Operating Drone Page 5
Align and Tips Page 6
Fly+Drive Drone — 5-inch

1Printed in China.
READ ALL WARNINGS AND PRECAUTIONS BEFORE USE
SAFETY WARNINGS
• Not recommended for children under 14 years of age. As with all electrical products, precautions should be
observed during handling and use to reduce the risk of electrical shock.
• Adult supervision is required at all times.
• Drive drone only on smooth flat surfaces.
• Never fly drones above or near people, sudden changes in wind or other conditions could lead to unexpected
crashes.
• Always use caution when flying drone vehicles, obey relevant laws, respect the privacy and property rights of
others.
• The drone shall never be modified or used for anything except its intended purpose.
• Before each use, an adult should review the product and battery to determine that no damage or hazards exist.
• DO NOT TOUCH SPINNING PROPELLERS.
• Do not allow anything to intentionally make contact in any way with spinning propellers
o Prevent contact with spinning blades by turning off remote prior to handling drone.
• Use caution and pay attention to your surroundings while operating drone.
• Do not fly drone into animals, people, or inanimate objects.
• Keep drone away from power lines, buildings, trees, public areas, and any other potentially hazardous areas.
• Do not operate in rain, heavy wind, and or any type of severe weather.
• Do not land drone on wet surfaces.
• Never touch or allow others to touch drone while it is flying.
• Always turn drone off when it is not in use.
• Always fly drone in large open areas.
• The drone will lose controlling capabilities if fly distance is more than maximum recommended altitude of 100 ft.
Keep below 100 ft. to avoid potential crashing risk.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Fly-aways are the responsibility of the individual
pilot and will not be replaced by the manufacturer.
WARNING: Changes or modifications to this unit not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
TROUBLESHOOTING:
When remote switch is turned on, the remote light does not
illuminate:
1) Check that batteries in the remote are installed correctly OR
2) Replace with new batteries
When the remote is switched on, the remote LED is flashing:
1) Remote batteries are low.
2) Replace them with new batteries.
Drone and remote properly pair, but the drone will not lift-off:
1) Drone Li-Po needs charging. Use charging cable to connect the
drone to power source.
After trimming the drone, the drone flight is very unstable and
cannot fly properly:
1) One or more blades are most likely damaged;
2) Turn off the drone and remote.
3) Replace with the proper number replacement blade and try
flying again.
After impact, the drone is unstable:
1) Put the left tremote control lever to the left bottom and put the
right remote control lever to the right bottom at the same time
which resets the drone (lights will flash quickly).
2) If the above does not resolve the issue, reboot the drone and
controller and pair again.
Remote Controller and Drone can not be paired:
1) Check Point: Remote Controller must be close to Drone, do not
exceed 4 meters.
Note: If there are 2 sets of Drones within 4 meters for Pairing, you
must pair one successfully before pairing the second set.
This drone weighs 0.163 (74g). As of December 21, 2015, the Federal
Aviation Administration (FAA) only requires registration on unmanned aircrafts
weighing more than .55 lbs. Visit www.faa.gov/uas/registration/ for more
information. Although the FAA does not require this drone to be registered,
ongoing compliance with federal, state, and local laws is an owner’s sole
responsibility. Always fly safely and respect the privacy of others.
Fly+Drive Drone — 5-inch

2Printed in China.
CONTENTS
LITHIUM-POLYMER BATTERY WARNING
BATTERY WARNING - ALKALINE (AA)
KEEP THIS INSTRUCTION MANUAL FOR REFERENCE
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.
• Insert batteries using the correct polarity. Do not short-circuit the supply terminal.
• Only use manufacturer specified batter(ies), charger(s), and/or adapters, if
applicable, specified by the manufacturer.
• Always use, replace, and recharge (if applicable) batteries under adult supervision.
Drone - 5in. Fly+Drive Drone
Drone Controller
There is a risk of fire and personal injury if Li-Po
battery is punctured, damaged or misused.
• Never expose battery to extreme temperatures
or moisture.
• Do not subject battery to strong impacts.
• Always keep battery away from flammable
materials.
• Only use manufacturer specified batter(ies),
charger(s), and/or adapters, if applicable.
• Battery is not serviceable.
• Let battery cool to room temperature before
charging.
• While charging, never leave battery unattended.
• Recycle or dispose of battery according to federal,
state and local laws.
Charge Cable Propellers
REMOTE BATTERY INFORMATION
1. Unscrew the remote battery door using a
Philips head screwdriver (not included).
2. Install 4 “AA” batteries as shown in the
diagram above.
3. Replace and close battery compartment.
ALIGN
TAKE OFF/LAND
SPIN TRIM
B
F
L R
Fly+Drive Drone — 5-inch

Printed in China. 3
Replacing Propellers
1. Pull firmly to remove broken propeller. Replace
with a new one. Push firmly and carefully.
2. Replace propellers by following the diagram on
the right.
3. Each blade spins differently. Blade A1 turns
clockwise and Blade B1 turns counter clockwise.
Connect the Charge
Cable to the Drone
CHARGING BATTERY
Note: The Battery Charger will light up when it is
charging the battery and turn off when the
battery is fully charged. Charge time is
approximately 120 minutes.
1. Turn off the drone before charging.
2. Connect the Battery Charger Cable to the
port found on the side of the drone.
3. Connect USB connector to the power source.
Insert the
Charge Cable
into a power
source
Fly+Drive Drone — 5-inch
A1
A1
B1
B1

4Printed in China.
REMOTE OVERVIEW
ALIGN
TAKE OFF/LAND
SPIN TRIM
B
F
L R
Align Button
(See pg. 6)
Auto Land
Throttle Joystick:
Increases or decreases
drone elevation
left/right controls spin
ON/OFF Button
Forward Adjustment
Right Adjustment
Multi Directional
Joystick
Backward Adjustment
Spin Trim
Left Adjustment
Fly+Drive Drone — 5-inch

5Printed in China.
10
FEET
10
FEET
10 FEET
5 FEET
10 FEET
OPERATING DRONE
Step 1 – Pre-Flight Checklist
• Read all warnings and instructions.
• Install remote batteries, page 2.
• Charge batteries, page 3.
• Make sure that drone and remote are powered off.
Step 2 – Choosing a location
• Drone is designed to be flown/driven indoors
and outdoors.
• Always make sure you have enough space to
fly drone.
• Always follow warnings, page 1.
Step 3 – Driving Mode
1. Turn the drone and remote on then place the drone on a hard flat surface and
allow to sit for 4 seconds.
Step 4 – Lift Off
1. Bring the car to a stop.
ALIGN
TAKE OFF/LAND
SPIN TRIM
B
F
L R
ALIGN
TAKE OFF/LAND
SPIN TRIM
B
F
L R
2. Pair remote to drone:
Bring the Throttle all the way
up then bring it all the way
down, remote will beep
once paired.
3. Use the right joystick to move
the car forwards, backwards
and turn left or right.
2. Press TAKE OFF/LAND button OR slowly press the Throttle
Joystick stick up. Drone will begin to elevate. You can compensate
for some of the drone’s drifting by using the Multi Directional Button
or by following step 5. You may need to practice this step several
times before successfully getting drone into the air.
Note: After pair is successful, keep the throttle in center to enter driving mode.
After pair is successful, you can enter flying mode by following step 4 (shown below).
Fly+Drive Drone — 5-inch

6Printed in China.
OPERATING DRONE (Cont.)
Step 5 – Operating Drone in Flight
Follow this step if your drone begins to drift
while take off or during flight.
F. Drone drifts backwards: Press the Forward
Adjustment Button.
B. Drone drifts forwards: Press the Backwards
Adjustment Button.
L. Drone drifts right: Press the Left Adjustment
Button.
R. Drone drifts Left: Press the Right Adjustment
Button.
Step 6 – Landing Drone
1. Lower drone to 20 feet or less then press the
Take Off Land button. Use the Multi
Directional Joystick to maneuver drone. Or
Push the left joystick down until the drone
landing.
2. In the event the blades will not stop spinning,
you can perform an emergency stop by pressing
and holding the TAK OFF/LAND button.
Step 7 – Retrieving Drone
1. Turn off your remote by pressing the Power
Button. This will stop you from accidentally
turning the propellers on.
2. Make sure the propellers have stopped
spinning then pick up your drone.
Note: You will need to pair your drone again
before your next flight.
Align
Press the Align Button to turn Align mode ON
and then again to turn off.
• In this mode, the drone will always move in
the direction you press the Multi Directional
Button no matter which way the drone faces.
Tips
• Do not crash drone into sand or dirt. Drone
gears may become clogged.
• When first learning to fly, practice lifting off
and hovering.
• Stay several feet from walls and buildings.
ALIGN
TAKE OFF/LAND
SPIN TRIM
B
F
L R
Use the Throttle Joystick to increase or
decrease your elevation. Push the throttle
to left, make the drone to rotate
conterclockwise. Push the throttle to
right, make the drone to rotate clockwise.
Use the Multi Directional Joystick
to move forwards, backwards or
side to side.
ALIGN
TAKE OFF/LAND
SPIN TRIM
B
F
L R
Lower drone to 20 feet or less then press the Auto Land button. Use
the Multi Directional Joystick to maneuver drone. Press the Auto Land
Button a second time to deactivate auto land.
ALIGN
TAKE OFF/LAND
SPIN TRIM
B
F
L R
Turn off your remote by pressing the
Power Button.
ALIGN
TAKE OFF/LAND
SPIN TRIM
B
F
L R
Align Button
Fly+Drive Drone — 5-inch