Showven SPARKULAR PRO BT71 User manual

Showven Technologies Co.,Ltd.
V1.0
SPARKULAR PRO
USER MANUAL

SPARKULAR PRO
User Manual
> Safety Considerations
★Please read this manual carefully before operating this product.
★Warranty card attached in the manual, please keep it well.
》Never touch the nozzle of SPARKULAR PRO, danger of getting burnt.
》Never touch the sparks which shooting out from the nozzle.
》Cover of nozzle of SPARKULAR PRO is prohibited.
》Keep audience, animals or flammable objects at a minimum distance of 3m from SPARKULAR PRO. Make sure sparks
shoot out from SPARKULAR PRO can NOT touch any objects in the air.
》Ensure that children, animals and unauthorized persons don’t have access to the SPARKULAR PRO!
》Unauthorized repair are prohibited, it may cause serious incident.
》Make sure lid of feeding hopper are well covered when use SPARKULAR PRO. Accidentally burning of Composite
Ti can only use sands to extinguish. Composite Ti should keep away from moisture and stored in a dry sealed
environment.
》please be noted that there may sparks or remains fall to the ground when use HC8200 LARGE, LARGEⅠ.
》Clear material is necessary both before and after the show. Please check nozzle of SPARKULAR PRO after each
show, if there are consumable agglomerated in the nozzle, please clear it with screwdriver, otherwise it will affect
the spark effects and even damage the machine.
》Maximum cascade of SPARKULAR PRO is 5 units (110V version is 3 units) with one standard power cable. Otherwise
it may damage the machine and even cause fire.
》For better heat dissipation, block the air intake and air outlet is prohibited.
Model BT71/BT72
Dimension 315 x 280 x 255mm
Weight 14kg
Input BT71: AC 220VAC-240VAC,50/60HZ; 600W
BT72: AC 100VAC-120VAC,50/60HZ; 700W
Work Temp. -10°C~50°C
Effect height HC8200 LARGEⅠ: 6-7m / HC8200 LARGE : 5-6m
Height adjustable Yes, gear 1~10
Effect direction Straight up
Hopper capacity 1200g
Control DMX
1

LED display area:
Control Button Area:
Radio Frequency Identification Area:
> Operating Panel
SPARKULAR PRO is specially designed for outdoor events, installations and projects. It is waterproof design and can be
used in heavy rainfall. Huge hopper design, guarantee as long as 60min effects time after fill up.
READY: Turns from flashing into long on, indicates that the machine is ready to work.
DMX: Flashing shows that DMX signal is connected, light OFF means there is no DMX signal
FAULT: Light ON when error occurs
HEAT: Light ON when system is heating up
MENU: switch through setup menu. Press 3s switch to advanced interface
DOWN: parameter down
UP: parameter up
ENTER: confirm and save parameters
RFID card comes together with HC8200. It is a safety design, allows machine to identify the parameter and types of
consumable.
Please note that granules RFID card can increase the single machine specific working time. The card is disposable, can
only use once.
2

First line: shows DMX address
Second Line: shows inner temp. and temp. bar, as well as error info if available
Error Information
Error Information
E0 System IC
E2 Temp. Sensor
E3 P Temp. Over
Explanation
Systematic error
Temperature sensor is not connected or damage
Chassis over-temperature
E4 Time Remain Activated time for machine is not enough, need to swip RFID card
E5 K Temp. Over Inner core over-temperature
E6 Heat Fail Heating Fail, if it recovery automatically, problem is shortage of power supply
Setting Menu
Press “MENU” switch through setup menu
Set DMX Address
Fountain Height Manual firing height setup, for test only
1-512
1-10
Auto Clear Delay Auto clear material time after each firing0.1-0.9s
Manual Fountain On/Off
Set DMX address
If controlled by Host Controller, please set DMX address as
1, 3, 5, 7,…2n-1, otherwise it may leads to signal interference
Manual firing, for test only
3
Main interface：
> Interface

For better performance of SPARKULAR PRO, please don’t change the default value of density without permis-
sion from SHOWVEN.
Press “MENU” 3 seconds to enter the advanced setup interface, press MENU key to enter
different options, wait 3 seconds to return to the main interface.
Advanced Menu
Option
Set Temperature
LCD Backlight
Density@ Height 1
Density@ Height 2
Range Explanation
Density@ Height 3
Density@ Height 4
Density@ Height 5
Density@ Height 6
Density@ Height 7
Density@ Height 8
Density@ Height 9
Density@ Height 10
Mode Selection
Motor Protect
Standby Switch
580-620
On/Off
80
80
80
80
80
100
100
100
40-100
40-100
Factory Mode
User Mode
On/Off
On/Off
Default is 580. Please don't change default value without
engineer's suggestion from SHOWVEN.
LCD screen backlight ON/OFF
Sparks density @ Height gear 1
Sparks density @ Height gear 2
Sparks density @ Height gear 3
Sparks density @ Height gear 4
Sparks density @ Height gear 5
Sparks density @ Height gear 6
Sparks density @ Height gear 7
Sparks density @ Height gear 8
Sparks density @ Height gear 9
Sparks density @ Height gear 10
Factory mode is for engineer only. When in Factory mode
machine can’t controlled by DMX console/host controller
Motor protect function, default setting is Off
When ON, the machine can firing only when heating up was
finished
4

Please follow bellowing rules to set DMX address when use SHOWVEN Host Controller, otherwise it may leads
to signal interference.
DMX Address
Sparkular No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35
SPARKULAR PRO occupy 2 channels
First Channel
0-15
16-255
Function
Firing OFF
Firing ON and with adjustable height
Second Channel Funciton
60-80 Firing ON and with adjustable height
20-40 Emergency Stop
0-10 Pre-heat OFF (disabled when auto-heat ON)
240-255 Pre-heat ON (disabled when auto-heat ON)
5

Warranty Instructions
Warranty Card
★Below situations NOT included in warranty service:
★Invoice and warranty card are necessary when applying for maintenance service from
SHOWVEN.
▲Sincere thanks for your choosing SPARKULAR PRO, you will receive quality service from us.
▲The product warranty period is one year. If there are any quality problems within 7 days after ship
ping out from our factory, we can exchange a brand new same model machine for you.
▲We will offer free of charge maintenance service for machines which with hardware malfunction
(except for the instrument damage caused by human factors)in warranty period. Please don't
repair machine without factory permission.
1. Damage caused by improper transportation, usage, management, and maintenance, or damage
caused by human factors;
2. Disassemble, modify or repair products without Showven’s permission;
3. Damage caused by external reasons (lightning strike, power supply etc);
4. Damage caused by improper installation or use;
For product damage not included in warranty range, we can provide paid service.
Product Name:
Purchase Date:
Tel:
Address:
Problem Feedback
Maintenance Detail:
Service Engineer:
Actual Problem:
Serial No.
Service Date:
6

Showven Technologies Co., Ltd
Add: BuildingB1,ChangshaECenterNo.18,XiangtaiRoad,LiuyangEconomic
DevelopmentZone,ChangshaCity,410300,HunanProvince,P.R.China.
Tel: [phone]
Web: www.showven.cn
E-mail: [email protected]