Showven SPARKULAR miniFALL BT14 User manual

User Manual
SPARKULAR miniFALL
V1.0

Page-1/6
User Manual
SPARKULAR miniFALL
Please read this manual carefully before operating the product.
This manual contains the warranty card, please keep it well.
Safety Considerations
》Never touch the nozzle of SPARKULAR miniFALL, danger of getting burnt;
》Never touch the sparks which shooting out from the nozzle.
》Unauthorized repair are prohibited, it may cause serious incident.
》Keep SPARKULAR miniFALL dry and do NOT use in rain or snow.
》Make sure lid of feeding hopper are well covered when use SPARKULAR miniFALL. Accidentally
burning of Composite Ti can only use sands to extinguish. Composite Ti should keep away from
moisture and stored in a dry sealed environment.
》Keep audience and flammable material at a minimum distance of 1m from SPARKULAR
miniFALL and the sparks it generated. Make sure sparks shoot out from Sparkular miniFALL can
NOT touch any objects.
》After the show, please stop preheating or powering off and move the SPARKULAR miniFALL only
after it cooling down for more than 5 minutes.
》The SPARKULAR miniFALL power supply cable (SPARKULAR miniFALL power supply EX-ca-
ble) maximum allowed cascade for SPARKULAR miniFALL is 12pcs, exceeded connecting may
result in damage .
》For better heat dissipation, block the air intake and air outlet is prohibited.
》Cover of nozzle of SPARKULAR miniFALL is prohibited.

Page-2/6
Feature：
》D-Quiet technology, no noisy
》Ultra-light weight
》Low power consumption
Sparkular miniFALL Model No.BT14
Parameter
Size
Hopper capacity
Material Consumption
Weight
Input
Working Power
Working Temperature
Casing
Fall Length
Interface
Double DMX input interfaces, double AC
power interfaces
3-4m(large)，2-3m(medium)
280g
15g/min
3kg
220 -240VAC, 50/60Hz
130w
-10℃~ 50 ℃
Anti-flame ABS
150×160×240mm

Page-3/6
Light emitting diode display area:
Bottom Indication Light：
READY：After turning on machine, it will automatically preheat around 6 minutes, when the
"READY" green light turns from flashing into long on, indicates that the machine is ready to work.
When it flashes slowly, it indicates some error.
DMX：Flashing shows that DMX signal is connected, otherwise is without signal
FAULT：When any malfunction , the light turns on
HEAT：When the machine is heating, signal light turns on
MENU：Short press to switch interface, press for 3 seconds can switch to the advanced setup
interface.
-：Parameters down
+：Parameters up
ENTER：Confirm and save parameters.
Quick Flashing：Preheating
Long on：Finish preheating and ready to work
Slow Flashing：Error warning
Composite Ti with RFID card, swiping cards used to identify
parameters and types of granules.
Please note that granules RFID card can increase the single
machine specific working time. The card is disposable, can only use
once.
Radio frequency identification area:
Operation Panel:
LCD information display area, showing operate menu and working status of machine.

Page-4/6
Interface
Main Interface:
Error informations display table：
Setting interface：
First line : Display DMX address is “1”.
Second line : Display the present inner core temperature and the temperature progress bar;
displays remianing time is 7 minutes and 24 seconds.
Press “MENU” to enter the Setting interface, press the “MENU” button to enter different options until
you return to the main interface.
Advanced menu：
Press “MENU” 3 seconds to enter the advanced setup interface, press MENU key to enter different
options, wait 3 seconds to return to the main interface.
Options
Set DMX
Address
Wireless
Control
Manual
Fountain
Range
1-512
ON/OFF
ON/OFF
Instructions
Set the DMX address.
Wireless function switch. you can match codeWhen shows “ON”
Manual fountain switch , for testing purposes only.
Error Informations Explanation
E0 System IC System error.
E2 Temp. Sensor Temperature sensor was damaged.
E3 P Temp. Over Machine stops working due to the chassis temperature is too high
E4 Time Remain Insufficient granules or remaining time, please swiping RFID card.
E5 K Temp. Over Machine stops working due to the inner core temperature is too high
E6 Heat Fail Heating failed.

Page-5/6
Please don’t set the same DMX address when controlling with host controller ZK6200/ZK6300.
Host controller can reduce the performance risk by monitor the working status of each machine.
Options Range
500-620
ON/OFF
70-100
Factory Mode/
User Mode
2 DMX Channel/
4 DMX Channel
Explanation
Set Temperature Setup inner Core temperature. Please don't change default
value without engineer's suggestion from SHOWVEN.
Auto Heat Auto preheat function switch after turning on
machine
Density Adjust the sparks density. Please don't change default
value without engineer's suggestion from SHOWVEN.
Mode Selection Factory Mode is factory debugging mode, User
Mode is using mode
DMX Channel
Mode
2 DMX Channel is standard mode, 4 DMX Channel
is speical mode.
On/OffStandby Switch When it’s on, the machine can only generate spark
when pre-heating finish.
Default Parameter Press “ENTER” to restore all parameters to the
factory settings.
Cable DMX mode：
When using the DMX controller, the system takes 2 channels
The First channel Functions
0-15 Fountain OFF
16-255 Fountain ON
The second channel Functions
60-80 Clear Material
20-40 Emergency Stop
0-10
240-255
Pre-heat OFF（Disable in Auto-heat）
Pre-heat ON（Disable in Auto-heat）

Page-6/6
Below situation NOT included in warranty service:
Warranty instructions
Warranty card
▲Sincere thanks for your choosing our products, you will receive quality service from us.
▲The product warranty period is one year, If there is any quality problems, we can exchangea
brand new same model machine to you within seven days after receive the product.
▲We will offer free of charge maintenance service for machines which with hardware malfunction
(except for the instrument damage caused by human factors) in warranty period. Please don't
repair machine without factory permission.
1.Damage caused by improper transportation, using, management, and maintenance, or damage
caused by human factors;
2.Disassemble, modified or maintenance products without Showven’s permission;
3.Damage caused by external reasons (lightning strike, power supply etc);
4.Damage caused by improper installation or use;
For product damage not included in warranty range, we can provide paid service.
Invoice and warranty card are necessary when asking for service from SHOWVEN.
---------------------------------------------------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------
Product Name:Serial NO.：
Maintenance Date:
Purchase Date:
Contact Number:
Address:
Customer Feedback
Information:
Actual malfunction:
Maintenance details:
Maintenance person:

Showven Technologies Co., Ltd
Add：Building B1, Changsha E-center No.18, Xiangtai Road, Economic & Technology
Development Zone, Hunan, China
Tel：[phone]
Fax：[phone]
Web：www.showven.com
E-mail：[email protected]