Showven SONICBOOM PLUS SMOKEJET User manual

USER MANUAL
SONICBOOM®PLUS SMOKEJET
V2.0
2021/04/23
Showven Technologies Co., Ltd.

USER MANUAL
SONICBOOM®PLUS SMOKEJET
★Please read this manual carefully before operating this product.
★Warranty card attached in the manual, please keep it well.
▲SAFETY ONSIDERATIONS
\ Unauthorized repair are prohibited, it may cause serious incident
\ Unauthorized repair are prohibited, it may cause serious incident.
\ This product is not waterproof design, please keep it dry, please do not use it when there are
fog fluid leakage or wet from rain.
\ Make sure power supply in consistent with the rated voltage of the equipment, and the
socket must well grounded. Unplug and turn off the machine when not use.
\ For adult use only, keep it away from fire, inflammable and explosive articles.
\ Installed in well ventilated area, ensure at least 50cm space around the machine, cover of the
nozzle is forbidden.
\ If the machine fails to work, please stop operation and unplug the machine. Check fog fluid,
fuse, power connection etc. carefully, if can’t solve the problem, please contact SHOWVEN or
your local SHOWVEN partner for advise.
\ Suggest use SHOWVEN original FX-S fog fluid, other fluid may lead to clog or malfunction.
Please do not adding any other material such as pigment, water etc to the fuel bottle.
\ To avoid fluid spill, make sure fog fluid not exceed related MAXIMUM fluid level line. When
install SONICBOOM in invert direction, the fuel bottle should installed upward.
\ In case of eye contact of fog fluid, please wash it with clean water. If fluid is swallowed
immediately look for medical advice.
▲Description
SONICBOOM PLUS is a new generational smokejet with dual output design, faster and thicker
effects. No generation of CO2, environmental friendly. Combined with SHOWVEN original FX-S
pro quick dissipating fog fluid guarantee the fast dissipating of the smoke.
▲Technical Specifications
\ MODEL: SONICBOOM® PLUS
\ DIMENSION: 500×324×325mm
\ WEIGHT: 28kg
\ VOLTAGE: 110V-220V,50/60Hz
\ FUSE: 15A/250V(220V),18A/250V(110V)
\ POWER: 3000W/1800W(220V),2400W/1800W(110V)
\ LED POWER: 9W×38pcs
\ MAX OUTPUT DISTANCE: 10m

\ MAX CONTINUOUS OUTPUT DURATION: 10s
\ OUTPUT: 80000cuft/min
\ FLUID CONSUMPTION RATE: 3min/L
\ TANK CAPACITY: 5L
\ DMX CHANNEL: 1/11/14
\ CONSUMABLES: FX-S
▲Operation Panel
1. Control button area
MENU: switch through setup menu
+: Parameter up; multiplex “TIMER”(smoke output time)
-: Parameters down; multiplex “VOLUME”(smoke output start)
ENTER: confirm and save parameters (screen will blink once when save successfully); multiplex
“STOP”.
NOTE: Screen will switch to main interface automatically if not press any button in long time.
▲Interface
1. Main interface:
First Line: DMX address, “:”blinks when there is DMX in signal.
Second Line: shows machine core temperature and pressure. The machine ready for operate
only when both temperature and pressure value close to 100%.
2. Error information:
Example of “TIMER”setting function in the menu:
1. “set interval 10s”
2. “set duration 2s”SONICBOOM will repeat: firing 2s, interval of 10s, firing 2s, interval
10s…Press “VOLUME”button under main interface, SONICBOOM activated and start to
generate smoke, and press “STOP”to stop the machine.
Error information
Explanation
E1 Pressure
Pressure faults, no fog fluid or pump error
E2 K temp. Sensor
Temperature sensor fault
E5 Temp Over
Circuit fault
E6 Heat Fail
Heating element damage or circuit fault or
unstable voltage

3. Setting Menu:
Press “MENU”switch through setup menu.
4. Advanced Menu:
Press “MENU”for 3s, enter advanced setting interface
▲DMX Channel
1. 1 channel mode:
LED color determined by single channel, DMX value and related color as below:
Color
SMOKE OFF
LED OFF
RED
GREEN
BLUE
PINK
LED OFF
DMX value
0-5
6-40
41-60
61-80
81-100
101-120
Color
PURPLE
ORANGE
YELLOW
SKY BLUE
WHITE
Random
236-255
DMX value
121-140
141-160
161-180
181-200
201-220
221-235
2. 11 channels mode:
Channels
Function
Channel 1
Firing: (0-9) OFF, ( 10-255) ON
Channel 2
Inner LED RED: (0-9) OFF, (10-255) LED brightness increase
Channel 3
Inner LED GREEN: (0-9) OFF, (10-255) LED brightness increase
Channel 4
Inner LED BLUE: (0-9) OFF, ( 10-255) LED brightness increase
Channel 5
Outer LED RED: (0-9) OFF, (10-255) LED brightness increase
Channel 6
Outer LED GREEN, (0-9) OFF, (10-2551) LED brightness increase
Channel 7
Outer LED BLUE, (0-9) OFF, (10-255) LED brightness increase
Channel 8
LED Random: (0-9) OFF, (10-255) LED random color, use together with
channel 9.
Channel 9
LED color change speed: (0-9) OFF, (10-255) LED color change speed
increase
Channel 10
LED strobe: (0-9) OFF, (10-255) LED strobe increase
Options
Range
Explanation
DMX 512 Address
1~499
Set DMX address
Power Regulation
Standard/Half Power
Setting working power for the machine
Color Optional
0~10
LED color set when manual firing
Channel Mode
1/11/14
DMX channel mode switch
Fog Volume
50%/80%/100%
Manual fog volume setup
Item
Value
Explanation
Manual Evacuate
ON/OFF
Manual Evacuate when pressure always
insufficient
Interval Set
1-200
Interval time
Duration Set
1-8
Smoke output duration
Wireless Remote
ON/OFF
Wireless ON/OFF switch
Language
Chinese/English
Language switch
Manual Pump
ON/OFF
For maintenance

Channel 11
LED dimmer, (0-9) OFF, (10-255) LED brightness increase
3. 14 channels mode:
Channels
Function
Channel 1
Firing: (0-9) OFF, ( 10-255) ON
Channel 2
Inner LED RED: (0-9) OFF, (10-255) LED brightness increase
Channel 3
Inner LED GREEN: (0-9) OFF, (10-255) LED brightness increase
Channel 4
Inner LED BLUE: (0-9) OFF, ( 10-255) LED brightness increase
Channel 5
Inner LED AMBER: (0-9) OFF, ( 10-255) LED brightness increase
Channel 6
Outer LED RED: (0-9) OFF, (10-255) LED brightness increase
Channel 7
Outer LED GREEN, (0-9) OFF, (10-2551) LED brightness increase
Channel 8
Outer LED BLUE, (0-9) OFF, (10-255) LED brightness increase
Channel 9
Outer LED AMBER, (0-9) OFF, (10-255) LED brightness increase
Channel 10
LED Random: (0-9) OFF, (10-255) LED random color
Channel 11
LED Random (inner LED change color): (0-9) OFF, (10-255) LED random
color
Channel 12
LED color change speed: (0-9) OFF, (10-255) LED color change speed
increase
Channel 13
LED strobe: (0-9) OFF, (10-255) LED strobe increase
Channel 14
LED dimmer, (0-9) OFF, (10-255) LED brightness increase
NOTE: Manual function disabled when DMX connected.
▲E1 Pressure error explanation
In order to protect pump, SONICBOOM will running self check program to find out whether
there are fog fluid in the fuel pipe.
1. E1 pressure error activation
When there is no fog fluid in the fuel tank, system can not reach preset pressure even turn on
for a long time. The pump will stop working, and report E1.
2. Way to clear E1 error
Fill the fog fluid tank, then restart the machine.
Press “VOLUME”to reset.
DMX Channel 1, start a firing.
▲Maintenance
1. Use SHOWVEN original fog fluid for the best effect of SONICBOOM. Warranty will be void if
any other type fluid is used.
2. Don’t disassemble the machine by unauthorized person, modifications to the machine are
not allowed.
3. Excessive dust, liquid or dirt etc on the equipment will affect performance of the machine
and cause poor heat dissipation. Remove dust with air compressor, vacuum or soft brush. Use a
damp cloth to clean the case.
4. Before storing the machine, run distilled water through the system to help avoid condensing
the pump or heater.

5. To keep the best status and performance of machine, it is recommended to running the
machine at least once per month.
6. After continuous use of 40h (or 1-2month), please use 35% vinegar with 65% distilled water
to wash the pump and pipe system by running the machine 10-15 times.
▲Possible reason for the block of atomizer
For healthy and best status of machine, please do use SHOWVEN original fog fluid.
A. Fluid spill: heat can’t effectively transmit to fog fluid, leads to insufficient atomization of the
fog fluid in the heating pipe.
Possible Reason 1: Use other type of low quality fog fluid instead of SHOWVEN original fog
fluid.
Possible reason 2: Use inappropriate fog fluid. For different types of fog fluid, the atomization
temperature is different.
B. Heating aluminum pipe clog: early symptom for heating aluminum pipe clog is fog fluid spill
caused by insufficient atomization. Use other brand fluid or not make regular maintenance for
a long time will definitely leads to pipe clog.
C. Solution for above problem: Use SHOWVEN original fog fluid. Make regular maintenance
(every 1-2month). Use 35% vinegar with 65% distilled water to wash the pump and pipe
system by running the machine 10-15 times.

Warranty Instructions
▲Sincere thanks for your choosing our products, you will receive quality service from us
▲The product warranty period is one year. If there are any quality problems within 7
days after shipping out from our factory, we can exchange a brand new same model
machine for you
▲We will offer free of charge maintenance service for machines which with hardware
malfunction (except for the instrument damage caused by human factors)in warranty
period. Please don't repair machine without factory permission
Below situations NOT included in warranty service:
1. Damage caused by improper transportation, usage, management, and maintenance, or
damage caused by human factors;
2. Disassemble, modify or repair products without permission;
3. Damage caused by external reasons (lightning strike, power supply etc.)
4. Damage caused by improper installation or use;
For product damage not included in warranty range, we can provide paid service.
Invoice and warranty card are necessary when applying for maintenance service from
SHOWVEN.
Warranty Card
Product Name:
Serial No.
Purchase Date:
Tel:
Address:
Info. feedback
about the
problem:
Actual problem:
Maintenance
detail:
Service Engineer:
Service Date:

Showven Technologies Co., Ltd.
Tel: [phone]
Web: www.showven.cn E-mail: [e-mail]
Add: Liuyang Economic Development Zone, Changsha, 410300, Hunan Province,
P.R.China