Showven SPARKULAR TRIPLE BT51 User manual

V1.0
SPARKULAR TRIPLE
USER MANUAL
Showven Technologies Co.,Ltd.

User Manual
SPARKULAR TRIPLE
Please read this manual carefully before operating the product.
This manual contains the warranty card, please keep it well.
Safety Considerations
》Never touch the nozzle of SPARKULAR TRIPLE, danger of getting burnt.
》Never touch the sparks which shooting out from the nozzle.
》Cover of nozzle of SPARKULAR TRIPLE is prohibited.
》Keep audience, animals or flammable objects at a minimum distance of 3m (for front and rear side)
and 5m (for left and right side) from SPARKULAR TRIPLE. Make sure sparks shoot out from SPARKU-
LAR TRIPLE can NOT touch any objects in the air.
》Ensure that children, animals and unauthorized persons don’t have access to the SPARKULAR
TRIPLE!
》Unauthorized repair are prohibited, it may cause serious incident.
》Keep SPARKULAR TRIPLE dry and do NOT use in rain or snow.
》Make sure lid of feeding hopper are well covered when use SPARKULAR TRIPLE. Accidentally burn-
ing of Composite Ti can only use sands to extinguish. Composite Ti should keep away from moisture
and stored in a dry sealed environment.
》Clear material is necessary both before and after the show. Please check nozzle of SPARKULAR
TRIPLE after each show, if there are consumable agglomerated in the nozzle, please clear it with
screwdriver, otherwise it will affect the sparks effects and even damage the machine.
》Maximum cascade of SPARKULAR TRIPLE is 2 units with one standard power cable. Otherwise it
may damage the machine and even cause fire.
》For better heat dissipation, block the air intake and air outlet is prohibited.
1

Feature:
》Triple heads, multi effect
》Each nozzle can be controlled separately
》Faster response, stronger bursts
》RDMX function, status can be monitored by original host controller
Operation Panel
LED display area:
READY1, READY2, READY3 shows the status of 3 heads respectively;
After turn on, the machine pre-heating automatically, pre-heating time is around 5min. When
“READY” turns from flashing into long on, indicates that the machine is ready to work.
DMX: Flashing shows that DMX signal is connected, otherwise is without signal
Model: BT51/BT52
Parameters
Dimension
Weight
Input
Work power
Working Temperature
Casing
Effect height
Hopper capacity
HC8200 consumption 17g/min * 3
20kg
BT51:AC200-240V, 50/60Hz
BT52:AC100-120V, 50/60Hz
1500w
-10℃~ 50 ℃
Metal
2.0-4.0m adjustable (HC8200 MEDIUM)
2.0-5.0m adjustable (HC8200 LARGE)
160g * 3
400×290×270mm
2

Page-3/6
Radio frequency identification area:
MENU: Short press to switch interface, press for 3 seconds can switch to the advanced setup interface.
DOWN: Parameters down
UP: Parameters up
ENTER: Confirm and save parameters
Composite Ti with RFID card, swiping cards to identify parameters and types of granules.
Please note that granules RFID card can increase the single machine specific working time. The card
is disposable, can only use once.
Interface
Main Interface:
Error information:
First line: temp. and error info. of each nozzle of machine Left shows nozzle 3, middle shows nozzle 2, right
show nozzle 1.
Second line: shows DMX address, and remaining working time 10min 22seconds
Error information Explanation
E0 System IC System error.
E2 Temp. Sensor Temperature sensor was damaged.
E3 P Temp. Over Machine stops working due to the chassis temperature is too high
E4 Time Remain Insufficient granules or remaining time, please swiping RFID card.
E5 K Temp. Over Machine stops working due to the inner core temperature is too high
E6 Heat Fail Heating failed.
Control button area:
3

Advanced menu:
Press “MENU” 3 seconds to enter the advanced setup interface, press MENU key to enter different
options, wait 3 seconds to return to the main interface.
Setting interface:
Press “MENU” to enter the Setting interface, press the “MENU” button to enter different options
until you return to the main interface.
Options
Set DMX Address
Manual Fountain
Fountain Height
Range
1-512
ON/OFF
1-10
Instructions
Set the DMX address.
Manual fountain switch, for testing purpose only.
Manual fountain, set shooting height, for testing purpose only.
Options Range
500-610
ON/OFF
70-100
Factory Mode/
User Mode
Explanation
Set Temperature Setup inner Core temperature. Please don't change
default value without engineer's suggestion from SHOWVEN.
Auto Heat Auto preheat function switch after turning on
machine
Density Adjust the sparks density. Please don't change default
value without engineer's suggestion from SHOWVEN.
Mode Selection Factory Mode is factory debugging mode, User
Mode is using mode
Default Parameter
Mode
Press “ENTER” to restore all parameters to the factory
settings.
On/OffStandby Switch When it’s on, the machine can only generate spark
when pre-heating finish.
When using the DMX controller, the system takes 6 channels, each nozzle takes 2 channels.
First channel (nozzle 1) Functions
0-15 Fountain OFF
16-255 Fountain ON, Height adjustable
Second Channel (nozzle 1) Functions
60-80 Clear Material
20-40 Emergency Stop
0-10
240-255
Pre-heat OFF（Disable in Auto-heat）
Pre-heat ON（Disable in Auto-heat）
4

Please set DMX address following below rules when connect with SHOWVEN host controller.
Note: Wrong DMX address setting may cause uncontrolled shooting of SPARKULAR TRIPLE.
SPARKULAR
TRIPLE No. 1 2 3 4 5 6
DMX Address 1 7 13 19 25 31
Third Channel (nozzle 2) Functions
0-15 Fountain OFF
16-255 Fountain ON, Height adjustable
Fourth Channel (nozzle 2) Functions
60-80 Clear Material
20-40 Emergency Stop
0-10
240-255
Pre-heat OFF（Disable in Auto-heat）
Pre-heat ON（Disable in Auto-heat）
Fifth Channel (nozzle 3) Functions
0-15 Fountain OFF
16-255 Fountain ON, Height adjustable
Sixth Channel (nozzle 3) Functions
60-80 Clear Material
20-40 Emergency Stop
0-10
240-255
Pre-heat OFF（Disable in Auto-heat）
Pre-heat ON（Disable in Auto-heat）
5

Below situation NOT included in warranty service:
Warranty instructions
▲Sincere thanks for your choosing our products, you will receive quality service from us.
▲The product warranty period is one year, If there is any quality problems, we can exchangea brand new
same model machine to you within seven days after receive the product.
▲We will offer free of charge maintenance service for machines which with hardware malfunction (except
for the instrument damage caused by human factors) in warranty period. Please don't repair machine with-
out factory permission.
1.Damage caused by improper transportation, using, management, and maintenance, or damage caused
by human factors;
2.Disassemble, modified or maintenance products without Showven’s permission;
3.Damage caused by external reasons (lightning strike, power supply etc);
4.Damage caused by improper installation or use;
For product damage not included in warranty range, we can provide paid service.
Invoice and warranty card are necessary when asking for service from SHOWVEN.
--------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Warranty card
Product Name: Serial NO.：
Maintenance Date:
Purchase Date:
Contact Number:
Address:
Customer Feedback
Information:
Actual malfunction:
Maintenance details:
Maintenance person:
6

Showven Technologies Co., Ltd
Add: BuildingB1,ChangshaECenterNo.18,XiangtaiRoad,LiuyangEconomicDevelopment
Zone,ChangshaCity,410300,HunanProvince,P.R.China.
Tel: [phone]
Web: www.showven.cn
E-mail: [email protected]