Shure 550L User manual

Model 550L User Guide
©2005, Shure Incorporated
27C8090 (Rev. 4)
Printed in U.S.A.
GENERAL
The Shure 550L is an omnidirectional dynamic base station
microphone with a frequency response specially tailored for
voice intelligibility. It is equally useful for radio
communications, paging and dispatching systems, and its
low-impedance connection makes it adaptable to most PA
amplifiers. The low-impedance design also makes it useful
for long runs of cable, or under severe hum disturbance
conditions.
The microphone is not affected by heat or humidity. Its
exclusive ARMO-DUR®case is immune to oil, grease,
fumes, salt spray, sun, rust, and corrosion–and is
outstanding in its ability to resist mechanical shocks and
vibration. The “Million-Cycle” leaf-type switch is designed to
withstand rigorous operating conditions and constant use.
Features
• Low-impedance operation
• Crisp, natural, high-intelligibility voice response
• Fingertip control bar actuates microphone circuit and exter-
nal relay or control circuit
• Long-life switch meets rigorous requirements of communi-
cations and paging systems
• Sturdy, high-impact ARMO-DUR base and microphone
case resists corrosion
• Reliability under all operating conditions
• Neoprene feet prevent microphone slipping
PRESS-TO-TALK SWITCH OPERATION
The fingertip control bar is a non-locking switch; simply
depress the control bar and release after transmission.
WIRING
Figure 1 shows the internal wiring of the 550L microphone.
INTERNAL CONNECTIONS
FIGURE 1
The 550L may be wired for balanced or unbalanced
operation. For unbalanced operation, the green cable wire
is connected to the audio input, the white cable wire is
connected to the audio ground, and the shield is connected
to the chassis ground. See Table 1.
For balanced operation, the green cable wire is connected
to the audio input positive (+), the white wire is connected to
the audio negative (-), and the shield is connected to the
chassis ground. See Table 1.
Table 1. Cable-to-Connector Wiring
NOTE: The red and black wires are not part of the audio circuit.
These wires provide a contact closure when the microphone
switch is depressed. This closure may be used to control an exter-
nal relay or transmit/receive circuit.
IMPEDANCE MATCHING
Low-impedance operation is extremely useful where long
cable lengths are required, or under conditions of severe
hum disturbance. The permissible cable length is practically
unlimited, since neither response nor level is appreciably
affected. Shure A95 Series Line Matching Transformers are
available for use in those cases where a low-impedance
microphone is to be used with an amplifier with a
high-impedance input. These transformers provide a proper
impedance match between a 19- to 300-ohm microphone
and a high-impedance input, and are available with various
input and output connectors.
INPUT TYPE
WIRE
COLOR
FUNCTION XLR
CONNECTOR
1/4 IN. PHONE
PLUG
GREEN AUDIO PIN 2 TIP
UNBALANCED WHITE AUDIO GROUND PIN 3 SLEEVE
SHIELD CHASSIS GROUND PIN 1 SLEEVE
GREEN AUDIO + PIN 2 TIP
BALANCED WHITE AUDIO - PIN 3 RING
SHIELD CHASSIS GROUND PIN 1 SLEEVE
BLACK
WHITE
RED
BLACK
WHITE
GREEN
SHIELD
TRANSMIT

SPECIFICATIONS
Type
Dynamic
Frequency Response
150 to 6,000 Hz (see Figure 2)
TYPICAL FREQUENCY RESPONSE
FIGURE 2
Polar Pattern
Omnidirectional
Impedance (at 1,000 Hz)
Microphone rating impedance is 150 ohms (220 ohms ac-
tual) for connection to microphone inputs rated at 75 to
300 ohms
Output Level (at 1,000 Hz)
Open Circuit Voltage* . . . . . . . . . .-54.0 dB/Pa (2.0mV)
*(1 Pa = 94 dB SPL)
Switch
Press-to-Talk Switch actuates microphone circuit and ex-
ternal relay or control circuit. Microphone circuit normally
open.
Cable
2.1m (7 ft) four-conductor, two-conductor shielded,
non-detachable
Case
Brown ARMO-DUR®with dull chrome-plated steel
screen
Dimensions
See Figure 3
OVERALL DIMENSIONS
FIGURE 3
Net Weight
836 grams (1 lb, 13-1/2 oz)
Shipping Weight
1.12 kilograms (2 lb, 7-1/2 oz)
Certification
Eligible to bear CE Marking. Conforms to European EMC
Directive 89/336/EEC. Meets applicable tests and
performance criteria in European Standard EN55103 (1996)
parts 1 and 2, for residential (E1) and light industrial (E2)
environments.
REPLACEMENT PARTS
Cartridge .................................................................... R96
Cable....................................................................... C32C
Switch.................................................................. RK321S
For additional service or parts information, please contact
the Shure Service Department at 1-800-516-2525. Outside
the United States, please contact your authorized Shure
Service Center.
20 200001000 1000050 100
98765432 98765432
+10
0
–10
Hz
dB
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉ
ÉÉ
ÉÉ
57 mm
(2-1/4 IN.)
57 mm
(2-1/4 IN.)
12.7 mm
(1/2 IN.)
TRAVEL
4.8 mm
(3/16 IN.)
264 mm
(10-3/8 IN.)
2.8 mm
(7/64 IN.)
28.6 mm
(1-1/8 IN.)
149 mm
(5-7/8 IN.)
66.7 mm
(2-5/8 IN.)
44.4 mm
(1-3/4 IN.)
SHURE Incorporated http://www.shure.com
United States, Canada, Latin America, Caribbean:
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: [phone] U.S. Fax: [phone] Intl Fax: [phone]
Europe, Middle East, Africa:
Shure Europe GmbH, Phone: [phone] Fax: [phone]
Asia, Pacific:
Shure Asia Limited, Phone: [phone] Fax: [phone]