Siemens SSB161.05UT User manual

Electromotoric actuator
SSB161.05UT
For pressure independent zone valves, small globe valves and 3-party valves
●Operating voltage AC/DC 24 V, positioning signal DC 0...10 V
●Self-calibrating to the valve stroke
●Direct mounting with coupling nut, no tools required
●Manually override
●Position and actuator motion indication (LED)
●Positioning force 200 N
●Parallel operation of multiple actuators possible
A6V13359034_en--_b
Smart Infrastructure
2023-05-17

2
Siemens
A6V13359034_en--_b
Smart Infrastructure
2023-05-17
Use
●For zone valves VVP.., VXP.., VMP..: compatible with SSB161.05UT
●Typically in chilled ceiling, VAV and fan coil unit applications
●Max.10 units of SSB161.05UT can operate in parallel, provided the controller output
suffices.
Technical design
When the actuator is driven by DC 0…10 V positioning signal, it produces a stroke, which is
transmitted to the valve stem.
DC 0…10 V positioning signal
●The valve opens / closes in proportion to the
positioning signal at Y.
●At DC 0 V, actuator stem is retracted, the normally
closed valve is fully closed.
●When there is no operating voltage, the actuator
maintains its current position.
Y = Positioning signal Y [V]
H = Percentage of calibrated valve stroke
LED indication
Status
LED indication patterns
Variants
SSB161.05UT
Stroke movement: Stem retracting
Flashing green in sequence: LED1-->LED2-->LED3 (500 ms each)
Stroke movement: Stem extending
Flashing green in sequence: LED3-->LED2-->LED1 (500 ms each)
Stem stays in position
At H0 - H40: Constant green (LED3)
At H40 - H60: Constant green (LED2)
At H60 - H100: Constant green (LED1)
Calibration
Flashing green (LED2): 100 ms on, 100 ms off
Error*
Constant red (LED2)
Manual operation
Flashing green/red alternatively (LED2): Green 500 ms, red 500 ms
* Hint: Error caused by mechanical jam or calibration failure. Calibration through resetting the
operating voltage required.
Type summary
Type
Stock
number
Operating
voltage
Running
speed
Running time
5.5 mm
Positioning
signal
Actuator
characteristic
SSB161.05UT
S55180-A148
AC/DC 24 V
5 s/mm
27.5 s ±25 %
DC 0…10 V
Linear
Ordering
When ordering, specify both type and quantity.

3
Siemens
A6V13359034_en--_b
Smart Infrastructure
2023-05-17
Example:
Type
Stock number
Designation
Quantity
SSB161.05UT
S55180-A148
Electromotoric actuator
2
Delivery
Valves and actuators must be ordered separately. For easier valve assembly, actuators
ordered separately have the actuator stem fully retracted.
Equipment combinations
Combinable valves
Type reference
Valve type
Kvs [m3/h]
PN class
Data sheet
VVP45..
2-port valves
0.25…6.3
PN 25
N4845
VVP45..S
2-port valves, for CONEX compression fittings
0.63…2.5
N4854
VXP45..
3-port valves
0.25…6.3
N4845
VMP45..
3-port valves with T-bypass
0.25…4.0
VMP45..S
3-port valves with T-bypass, for CONEX compression
fittings
0.63…2.5
N4854
Note: To ensure trouble-free operation of
third-party valves with the actuator, the
valves must satisfy the following
requirements:
●Threaded connections with coupling nut:
¾” inch
●Nominal force: > 200 N
●Dimension X ≥ 8.3 mm
●Dimension Y ≤ 14.8 mm
Controllers
Type
AC/DC 24 V; DC 0…10 V
DXR2
DXR2..
RXB..
RXB39.1..
Combinable room thermostats
Type
Detail
RDG..
RDG160KN, RDG160T, RDG260, RDG405KN
RDU..
RDU340
RCU..
RCU50..

4
Siemens
A6V13359034_en--_b
Smart Infrastructure
2023-05-17
Product documentation
Topic
Title
Document ID
Mounting and installation
Mounting instructions
A6V13464210
Standards and directives
CE declarations
A5W00254962A
RCM conformity
A5W00254983A
Environmental compatibility
Environmental declarations
A5W00244689A
Related documents such as the environmental declarations, declarations of conformity, etc.,
can be downloaded from the following Internet address:
www.siemens.com/bt/download
Notes
Engineering
The actuators must be electrically connected in accordance with local regulations (see
"Connection diagrams [▶11]”).
CAUTION
National safety regulations
Failure to comply with national safety regulations may result in personal injury and property
damage.
●Observe national provisions and comply with the appropriate safety regulations.
Observe permissible temperatures (see "Technical data [▶9]").
Mounting
WARNING
●Do not use pipe wrenches, pliers or similar tools.
●Avoid lateral pressure or (cable) tension on the mounted actuator!
Valve and actuator are easy to assemble on site before commissioning:
●Remove protective cover from the valve body.
●Position the actuator and tighten the union nut manually.
●See "Mounting instruction" for graphical instructions.
Orientation

5
Siemens
A6V13359034_en--_b
Smart Infrastructure
2023-05-17
Installation
A [mm]
B [mm]
C [mm]
5.5
6.0
40
Crimp ferrule on stripped wire of connecting cable.
●Observe all admissible temperatures (see "Technical data [▶9]").
●Do not twist the cable.
●Magnets can damage the actuator.
●Provide a means for isolation from the power supply, e.g., connecting a circuit breaker or
switch fuse upstream of the control unit.
CAUTION
National safety regulations
Failure to comply with national safety regulations may result in personal injury and property
damage.
●Observe national provisions and comply with the appropriate safety regulations.
CAUTION
Phase cut and pulse-duration-modulated (PDM) signals are not permitted.
Regulations and requirements to ensure the safety of people and property must be
observed at all times!
Commissioning
When commissioning, check wiring and functioning of the actuator.
●Actuator stem extends
Normally open valve closes, normally closed valve opens
●Actuator stem retracts
Normally open valve opens, normally closed valve closes
NOTICE
The actuator must be commissioned only with a correctly mounted valve in place!

6
Siemens
A6V13359034_en--_b
Smart Infrastructure
2023-05-17
Self-calibration
When operating voltage is applied, the actuator self-calibrates (fully retracted ➙fully
extended ➙setpoint).
CAUTION
Never intervene manually during self-calibration.
NOTICE
●Correct calibration is only possible with valve stroke > 1.2 mm. Valve stroke < 1.2 mm
results in calibration failure.
●If calibration fails, the actuator performs another calibration automatically after
10 seconds.
●After three failed calibration attempts, the actuator stem remains in the extended
position and the valves are closed. The state of the LED then changes to "stays red".
Power
On
Calibration Y
t
Fully retracted
Fully extended

7
Siemens
A6V13359034_en--_b
Smart Infrastructure
2023-05-17
Manual operation
A 3-mm Allen wrench can be used to move the actuator to any position.
To move the actuator stem manually
1. Open the cover using a proper screwdriver.
2. Press and hold down button (a) illustrated below for at least three seconds.
–The actuator ignores any positioning signal from the controller.
3. Adjust the position of the actuator stem by rotating Allen wrench (b) illustrated below
clockwise or anti-clockwise.
–The actuator stem moves down if you rotate clockwise; it moves up if you rotate anti-
clockwise. The manually set position is retained.
4. To exit manual operation mode, press and hold down button (a) illustrated below again
for at least three seconds.
–The actuator runs a self-calibration automatically. Positioning signal sent from the
controller takes effect.
NOTICE
If operating voltage is applied to actuator, press button (a) before and after manually
adjusting the position of the actuator stem. If no operating voltage and positioning
signal are applied, manual operation can be done without pressing button (a).
Cabling operation
1. Unscrew cover screw
2. Remove cover
3. Connect or disconnect wire terminals
4. Install the cover
5. Screw in the cover screw
Maintenance
The actuators require no maintenance.
3 mm
(b)
(a)
>3s
A6V13359034Z00

8
Siemens
A6V13359034_en--_b
Smart Infrastructure
2023-05-17
WARNING
Operating voltage must be switched off during any site!
NOTICE
When carrying out service work on the plant, note the following:
●If necessary, disconnect electrical connections from the terminals.
●The actuator must be commissioned only with a correctly mounted valve in place!
Disposal
The device is considered an electronic device for disposal in accordance
with European guidelines and may not be disposed of as domestic waste.
●Dispose of the device through channels provided for this purpose.
●Comply with all local and currently applicable laws and regulations.
Warranty
Technical data on specific applications are valid only together with Siemens products listed
under "Equipment combinations". Siemens rejects any and all warranties in the event that
third-party products are used.
Open Source Software (OSS)
Software license overview
These devices use Open Source Software (OSS). All Open Source Software components
used in the product (to include copyrights and licensing agreement) are available at
http://siemens.com/bt/download.
Firmware version
OSS document
Device
Document ID
Title
2.10.0 or above
A6V13503690
Readme OSS for Modulating Room Actuator 200N, 300N
All

9
Siemens
A6V13359034_en--_b
Smart Infrastructure
2023-05-17
Technical data
Power supply
Operating voltage
AC 24 V (±15 %) or DC 24 V (±20 %)
Frequency
50/60 Hz
Power consumption
3 VA
Primary fuse or breaker rating
External, 2 A quick blow
Signal input
Positioning signal
DC 0…10 V
Input impedance
100 kOhm
Parallel operation (number of actuators)
Max. 101)
1) Provided that the controller output is sufficient.
Operating data
Position with de-energized positioning signal Y
See "Technical design [▶2]"
Running speed
< 5 s/mm ±25 %
Positioning force
200 N
Stroke
1.2…6.5 mm
Permissible temperature of medium in the connected valve
1…120℃
Electrical connection (connecting cable integral)
Permissible length for signal lines
<20 m
Wire cross section
0.5...0.75 mm²
Cable diameter
<5 mm
Mounting
Connection to valve
Plastic coupling nut ¾” inch
Orientation
360°
Standards
EU conformity (CE)
A5W00254962A
RCM conformity
A5W00254983A
UKCA
A5W00257055A
Housing protection degree
IP 54
Protection class according to EN 60730
III
Pollution degree
2

10
Siemens
A6V13359034_en--_b
Smart Infrastructure
2023-05-17
Standards
Overvoltage category
III
Environmental compatibility
The product environmental declaration
(A5W00244689A) contains data on environmentally
compatible product design and assessments (RoHS
compliance, materials composition, packaging,
environmental benefit, disposal).
UL Approval
Federal Communications Commission
UL as per UL60730-1, UL60730-2-14
http://ul.com/database
cUL as per CSA –CAN E60730-1, E730-2-14
FCC CFR 47 Part 15 Class B
ICES003
CAN ICES-3 (B)/NMB-3(B)
FCC regulations
Modification of this device to receive cellular radio telephone service signals is pro-
hibited under FCC rules and federal law.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Housing color
Cover/base
2003, Ti-Gray
Coupling nut
RAL 9017
General ambient conditions
Operation
Transport
Storage
Temperature
1…50 ℃
-25…70 ℃
-25…70 ℃
Humidity
5…95 % r.h.
non condensing
<95 % r.h.
non condensing
5…95 % r.h.
non condensing
Atmospheric
pressure
Min. 700 hPa, corresponding to
max. 3,000 m above sea level
-
-