Siemens Gigaset AS200 User manual

1
AS200-AS200A / GRC EN / A31008-M2208-T101-1-8U19 / Overview.fm / 12.11.2010
Gigaset AS200/AS200A
±V
11.12. 11:56
INT MENU
1Chargestatusof
the batteries
2Answermachineicon
(AS200A only)
3Displaykeys
4Messagekey
Flashes: new messages
received
5Directorykey
6 Control key (u)
7 Talk key
8Endcalland
On/Off key
9 Ringer on/off
(press and hold
in idle status)
10 Keypad lock on/off
(press and hold)
11 Recall key
- Consultation call
(flash)
- Dialling pause
(press and hold)
12 Microphone
13 "Microphone off" key
The base station at a glance
AS200A base station
AS200 base station
76
5
12
3
4
1
10
2
3
5
7
4
6
8
12
1
The handset at a glance
11
13
9
1Registration/paging key:
Search for handsets (press briefly, "Paging" ¢page 10)
Register handsets (press and hold ¢page 10).
2On/Off key: activate and deactivate answer machine.
Lights up: answer machine is activated.
Flashes: there is at least one new message or message is in the process
of being recorded.
Flashes very quickly for about four seconds: memory is full.
3Volume keys: (–= quieter; += louder)
During message playback: adjust the speaking volume.
While phone is ringing: adjust ringer volume.
4Play/Stop key:
Play back messages from the answer machine, or cancel playback.
During message playback:
5 Delete current message.
6 Skip to the start of the current message (press once) or go to the pre-
vious message (press twice).
7Skiptonextmessage.
Display keys on handset:
Pressing a key launches the function that
appears above that key in the display.
Display
icon
Function when pressed
INT Call other registered handsets
¢page 10.
MENU Open main/submenu (see
Menu tree ¢page 16).
“ Go back one menu level.
UScroll up/down or adjust vol-
ume with u.
T Move cursor to left/right
with u.
˜Backspace deletes one charac-
ter at a time from right to left.
OK Confirm menu function or save
entry.

2
AS200-AS200A / GRC EN / A31008-M2208-T101-1-8U19 / Overview.fm / 12.11.2010
Safety precautions
Emergency numbers cannot be dialled if the keypad lock
(¢page 1) is activated!
Not all of the functions described in this user guide are avail-
able in all countries.
Care
Wipe down the base station and handset with a
damp cloth (no solvents) or an antistatic cloth. Never
use a dry cloth. This can cause static.
Contact with liquid
If the handset should come into contact with liquid:
◆Switch the handset off and remove the batteries
immediately.
◆Allow the liquid to drain from the handset.
◆Pat all parts dry, then place the handset with the
battery compartment open and the keypad facing
down in a dry, warm place for at least 72 hours
(not in a microwave, oven etc.).
◆Do not switch on the handset again until it is
completely dry.
When it has fully dried out, you will normally be able
to use it again.
Read this user guide and the safety precautions carefully
before use. Explain their content and the potential hazards
associated with using the telephone to your children.
Only use the mains adapter supplied.
Fit only the recommended, rechargeable
batteries (¢page 13), i.e. never use any other
battery type or non-rechargeable batteries as this
could result in significant health risks and personal
injury.
The operation of medical appliances may be
affected. Be aware of the technical conditions
in your particular environment, e.g. doctor's sur-
gery.
Do not hold the rear of the handset to your ear
when it is ringing. Otherwise you risk serious and
permanent damage to your hearing.
The handset may cause an unpleasant humming
noise in hearing aids.
Do not install the phone in a bathroom or shower
room. The handset and base station are not
splashproof.
Do not use your phone in environments with a
potential explosion hazard, e.g. paint shops.
If you give your Gigaset to someone else, make
sure you also give them the user guide.
Please remove faulty base stations from use or
have them repaired by our service, as they could
interfere with other wireless services.
Disposal
Batteries should not be disposed of in general
household waste. Observe the local waste dis-
posal regulations, details of which can be obtained
from your local authority or the dealer you pur-
chased the product from.
All electrical and electronic equipment must be
disposed of separately from general household
waste using the sites designated by local authori-
ties.
If a product displays this symbol of a crossed-out
rubbish bin, the product is subject to European
Directive 2002/96/EC.
The appropriate disposal and separate collection
of used equipment serve to prevent potential
harm to the environment and to health. They are a
precondition for the re-use and recycling of used
electrical and electronic equipment.
For further information on disposing of your used
equipment, please contact your local authority,
your refuse collection service or the dealer you
purchased the product from.
$
ƒ
ECO DECT
You are helping to protect the environment with
your Gigaset AS200/AS200A.
Reduced energy consumption
Your telephone has a power-saving adapter plug
and uses less power.
Reduced transmission power
The transmission power of your telephone is
reduced automatically:
The handset's transmission power is reduced
depending on the distance to the base station. The
transmission power on the base station is reduced
to virtually zero when only one handset is regis-
tered and the handset is in the base station.
You can reduce the transmission power of the
handset and base station even more by using Eco
Mode/Eco Mode+ (see Menu tree ¢page 17):
◆Eco Mode: 80% transmission power reduction
in standby mode and during a call (the range of
the base station is reduced).
◆Eco Mode+: 100% transmission power deacti-
vation in standby mode (top left display icon ½).
Press and hold the talk key cto check that the
base station can be reached. You will hear the
ringing tone if the base station can be reached.
Registering handsets that do not support Eco
Mode+ causes the mode to be deactivated on
the base and all other handsets.
!

AS200-AS200A / GRC EN / A31008-M2208-T101-1-8U19 / starting.fm / 12.11.2010
3
First steps
Check the pack contents
◆one Gigaset AS200/AS200A base station,
◆one mains adapter,
◆one Gigaset AS200 handset,
◆one phone cord,
◆two batteries,
◆one battery cover,
◆one user guide.
If you have purchased a model with multiple handsets, the package should contain two bat-
teries, a battery cover and a charging cradle with mains adapter for each additional handset.
Setting up the base station and charging cradle (if included)
The base station and charging cradle are designed for use in enclosed dry rooms with a tem-
perature range of +5°C to +45°C.
¤Set up the base station at a central location on a flat, non-slip surface in your house or
apartment.
The phone's feet do not usually leave any marks on surfaces. However, due to the multitude of
different varnishes and polishes used on today's furnishings, the occurrence of marks on the
surfaces cannot be completely ruled out.
You can also mount the base station and charging cradle on the wall.
Please note:
◆Never expose the telephone to the influence of heat sources, direct sunlight or other elec-
trical devices.
◆Protect your Gigaset from moisture, dust, corrosive liquids and vapours.
Connecting the base station
¤First connect the mains adapter 1.
¤Then connect the telephone jack 2and
insert the cables into the cable ducts.
Please note:
◆The mains adapter must always be con-
nected, as the phone will not operate
without mains connection.
◆Only use the mains adapter and
phone cord supplied. Pin connections
on telephone cables can vary.
Please note
Pay attention to the range of the base station.
This is up to 300 m in unobstructed outdoor areas and up to 50 m inside buildings. The
range is reduced when Eco Mode (¢page 17) is activated.
1
1
1
2

AS200-AS200A / GRC EN / A31008-M2208-T101-1-8U19 / starting.fm / 12.11.2010
4
Connecting the charging cradle (if included)
Setting up the handset for use
The display is protected by a plastic film.
Please remove the protective film!
Inserting the batteries and closing the battery cover
¤Connect the flat plug from the power supply 1.
¤Plug the mains adapter into the plug socket 2.
If you need to disconnect the plug from the charging cradle,
press the release button 1and disconnect the plug 2.
1
2
1
2
Warning
Use only the rechargeable batteries (¢page 13) recommended by Gigaset
Communications GmbH. Never use conventional (non-rechargeable) batteries, as this
could result in significant health risks and damage to property. For example, the outer cas-
ing of the batteries could be destroyed or the batteries could explode. The phone could
also malfunction or be damaged as a result of using batteries that are not of the recom-
mended type.
¤Insert the batteries the right way
round.
The polarity is indicated in/on
the battery compartment.
¤Slide the battery cover back into the
main casing until it clicks into place.
If you need to open the battery cover, for
instance to replace the batteries, place
your fingertip in the grooved area on the
top of the cover and slide down.
+–

AS200-AS200A / GRC EN / A31008-M2208-T101-1-8U19 / starting.fm / 12.11.2010
5
Placing the handset in the base station and registering
If you have purchased a model with multiple handsets, repeat the registration process for
each individual handset. Handsets are assigned the lowest available internal number (1–4). If
more than one handset is registered to the base station, the internal handset number appears
in the top left of the display, e.g. 2. If the internal numbers 1–4 are already assigned to other
devices, number 4 will be overwritten.
Initial charging and discharging of the batteries
The correct charge level can only be displayed if the batteries are first fully charged and dis-
charged.
Please note
◆Each key press interrupts the automatic registration.
◆If automatic registration does not work, the handset will have to be registered manu-
ally (¢page 10).
◆Only place the handset in the base station or charging cradle that is intended for it.
V
Registering
V
INT MENU
Before you can use the phone, you must first register the handset
to the base station.
The handset registers automatically. Reg-
istration can take up to 5 minutes.
Do not remove the handset from
the base station during this time.
After successful registration, the idle screen is displayed.
Charge status of the batteries:
–= e V U(flat to full)
–=flashes: batteries almost flat
–e V Uflashes: charging
V
Put into base
MENU
¤Place the handset with
the display facing up
in the base station.
¤Place the handset in the base station or charging cradle for eight hours.
¤Then remove the handset from the base station or charging cradle and do
not replace it until the batteries are fully discharged.
8 h

AS200-AS200A / GRC EN / A31008-M2208-T101-1-8U19 / starting.fm / 12.11.2010
6
Setting the date and time
Set the date and time so that the correct date and time can be assigned to incoming calls, and
so that the alarm can be used.
MENU ¢Settings ¢OK ¢Date/Time ¢OK
¢Date: ¢~(enter the day, month and year in 6-digit format) ¢OK
¢Time: ¢~(enter hours and minutes in 4-digit format) ¢OK (display message: Saved)
¢a(press and hold to return to idle status)
Display in idle status
Once the phone is registered and the time set,
the idle display is shown as in this example.
If the answer machine is activated (AS200A), the answer
machine icon× will be displayed in the header. Your
answer machine is set with a pre-recorded announcement.
Activating/deactivating the handset
Press and hold the end call key ato activate or deactivate
the handset.
If you place a deactivated handset in the base station or charging cradle, it will automatically
activate.
Your phone is now ready for use!
If you have any questions about using your phone, please read the tips on troubleshooting
("Questions and answers" ¢page 13) or contact our Customer Care team ¢page 14.
Please note
◆After the first battery charge and discharge you may replace your handset in the base
station or charging cradle after every call.
◆Always repeat the charging and discharging procedure if you remove the batteries
from the handset and reinsert them.
◆The batteries may warm up during charging. This is not dangerous.
◆After a while, the charge capacity of the batteries will decrease for technical reasons.
Please note
When entering the time and date, you can move the position of an entry to the left or right
by pressing the control button up or down.
±V
11.12. 11:56
INT MENU

7
AS200-AS200A / GRC EN / A31008-M2208-T101-1-8U19 / main.fm / 12.11.2010
Making calls
Making external calls and ending
calls
External calls are calls using the public telephone net-
work.
~(Enter the phone number) ¢c.
The phone number is dialled. (Or you can first press
and hold c[dial tone] and then enter the number.)
During the call you can adjust the earpiece volume
using tand set the volume with u.
End the call/cancel dialling:
Press the end call key a.
You can automatically insert a network provider dial-
ling code before any phone number (see Menu tree
"Preselection" ¢page 17).
Accepting a call
The handset indicates an incoming call by ringing
and by a display on the screen.
Press the talk key cto accept the call.
When Auto Answer is activated (see Menu tree
¢page 17), simply remove the handset from the
base station/charging cradle.
In idle status, use tto activate the menu for setting
the call volume and use uto set the volume.
Calling Line Identification
When you receive a call, the caller's number will be
displayed on your handset; the caller's name will be
displayed if it is stored in the directory.
Requirements:
1You have asked your network provider for the call-
er's number (CLIP) to be displayed on your hand-
set screen.
2The caller has asked the network provider for his
number to be identified (CLI).
®appears in the display if you have
not requested Calling Line Identification,
Withheld appears if the caller has withheld CLI, and
Unavailable appears if CLI has not been requested.
Switch to mute
You can mute your handset when making external
calls. Your caller can no longer hear you.
Press the "Microphone off" key mduring the call to
activate/deactivate the function.
Using the directory and lists
Directory
To open the directory: press h.
You can store up to 60 numbers (max. 32 digits)
and associated names (max. 14 characters).
Enter letters/characters ¢page 12.
Saving the first number in the directory
h¢New Entry? ¢OK
¢~(enter number) ¢OK
¢~ (enter name) ¢OK
Storing a number in the directory
h¢MENU ¢New Entry ¢OK
¢~(enter number) ¢OK
¢~ (enter name) ¢OK
Selecting a directory entry
Open the directory with h.You have the following
options:
◆Use uto scroll through the entries until the
required name is selected.
◆Enter the first character of the name and scroll to
the entry with u, if required.
Dialling with the directory
h¢u (select entry) ¢c
Using other functions
h¢u(select entry) ¢MENU
The following functions can be selected with u:
New Entry Save new phone number.
Show Number Display the phone number.
Use Number Edit or add to the number.
Then dial or select other
functions from the MENU.
Edit Entry Edit selected entry.
Delete Entry Delete selected entry.
Send Entry Send a single entry to another
handset (¢page 8).
Delete List Delete all directory entries.
Send List Send the complete list to another
handset (¢page 8).
Shortcut For shortcuts, assign the current
entry to a key.

8
AS200-AS200A / GRC EN / A31008-M2208-T101-1-8U19 / main.fm / 12.11.2010
Using shortcut keys
You can assign directory entries to the keys 0 and 2–9:
h¢u(select entry) ¢MENU ¢Shortcut ¢OK
¢~(press the key you want to assign the entry to)
To dial, press and hold the required shortcut key.
Transferring the directory to another handset
Requirements:
◆The sending and receiving handsets must both be
registered to the same base station.
◆The other handset and the base station can send
and receive directory entries.
h¢u (select entry) ¢MENU ¢Send Entry /
Send List ¢OK ¢~(enter the internal number of
the receiving handset) ¢OK
Last number redial list
This list contains the ten last dialled numbers.
Dialling from the last number redial list
c(press briefly) ¢u (select entry) ¢c
Managing entries in the last number redial list
c(press briefly) ¢u (select entry) ¢MENU
You can select the following settings:
Calls list/voicemail (network mailbox)
list
An advisory tone sounds and the message key
flashes as soon as a new entry appears in the calls
list/voicemail list. A message appears in the display.
When you press the fkey, all the lists are displayed.
If only one list contains new messages, this will be
opened automatically.
Calls list
Precondition: CLIP (¢page 7)
Depending on the type of list set, the calls list con-
tains (¢page 17)
◆answered calls
◆missed calls
◆calls recorded by the answer machine
(AS200A only)
Depending on the type of list set, all numbers of the
last 25 incoming calls are saved or just the missed
calls are saved.
The calls list is displayed as follows:
Number of new entries + number of old, read entries
Open the calls list
f¢CallsList 01+02 ¢OK
The last incoming call is displayed.
If necessary, use uto select another entry.
Using other functions
u(select entry) ¢MENU
The following functions can be selected with u:
Calling back a caller from the calls list
f¢CallsList 01+02 ¢OK ¢u(select entry)
¢c
Voicemail list (AS200A)
You can use the voicemail list to listen to the mes-
sages that are on the answer machine.
The voicemail list is displayed as follows:
Number of new messages + number of old, played back mes-
sages
Opening the voicemail list
f¢VoiceMail 01+02 ¢OK
If you have new messages, playback will start with the
first new message, otherwise with the first old mes-
sage.
Use Number Edit or add to the number.
Then dial or select other
functions from the MENU.
Copy to Dir. Copy an entry to the directory.
Delete Entry Delete selected entry.
Delete List Delete all entries.
Please note:
If calls are saved in the network mailbox, you will
receive a message if the appropriate settings have
been set (depending on your network provider).
Delete Entry Delete current entry.
Copy to Dir. Copy an entry to the directory.
Date/Time Call date and time (if set).
Status New Call: new missed call.
Old Call: entry already read.
Answ.: call taken.
Delete List Warning! All old and new entries
will be deleted.
CallsList 01+02
VoiceMail 01+02

9
AS200-AS200A / GRC EN / A31008-M2208-T101-1-8U19 / main.fm / 12.11.2010
Using other functions
u(select entry) ¢MENU
The following functions can be selected with u:
Answer machine operation
(AS200A)
The answer machine can be operated from the hand-
set or by using the key on the base station
(¢page 1).
The telephone is supplied with a pre-recorded
announcement. You can only record your own
announcement messages using the handset. This
pre-recorded announcement is used if no personal
announcement is available.
If the memory is full, the answer machine switches
itself off automatically. It activates again automati-
cally when you delete old messages.
Activating/deactivating the answer machine
MENU ¢Voice Mail ¢OK ¢Answer Mach.
¢OK (‰= on)
When the answer machine is switched on,
the ±icon appears in the display.
Recording your own announcement
MENU ¢Voice Mail ¢OK ¢Announcements
¢OK
¢Rec announce ¢OK ¢Speak after OK ¢OK
You hear the ready tone (short tone). Now say your
announcement (at least 3 seconds). Press OK to con-
firm or press aor ”to reject your recording. After
recording, the announcement is played back for you
to check.
Please note:
Recording ends automatically when the max. record-
ing time of 170 seconds is reached or if there is a
break in speaking of more than 2 seconds.
Playing back or deleting announcements
See Menu tree ¢page 16.
Playing/deleting messages
Open the voicemail list to play back messages.
Stopping and controlling playback
During message playback:
Deleting individual messages
While playback is paused, press the ˜display key.
Deleting all old messages
During playback or pause:
MENU ¢Delete all old ¢OK (confirm the security
prompt)
Picking up a call from the answer machine
You can still accept a call while the answer machine is
recording the message by pressing c. Recording
stops and you can speak to the caller.
Setting up the answer machine
The answer machine has already been preset at the
factory. Make individual settings using the handset.
Details on how to set a delay time, after which the
answer machine is to answer a call, as well as details
on how to set the recording length and activate call
screening during the recording, are available from the
Menu tree ¢page 16.
Setting a different language
You can change the language used for voice prompts
and the pre-recorded announcement.
MENU ¢4 3921 (starts the procedure).
Select the language:
0(xxxx), 1(xxxx), 2(xxxx).
The display shows Saved.
Assigning key 1 for fast access to the
answer machine (network mailbox)
Simply press and hold key 1on the handset and you
will be connected directly to the answer machine
(network mailbox).
See Menu tree ¢page 16.
Continue Resume paused playback.
Volume Set the volume.
Copy to Dir. Copy an entry to the directory.
Delete all old Delete all old messages.
2Stop playback.
Press 2again to resume.
tGo to the start of the current message.
2 x tSkip to the previous message.
vSkip to the next message.
2 x vGo to the next message but one.

10
AS200-AS200A / GRC EN / A31008-M2208-T101-1-8U19 / main.fm / 12.11.2010
Remote operation when on the move
You can check and activate your answer machine
from any other telephone (hotel, pay phone etc.).
Requirements:
◆You have set a system PIN other than 0000
¢page 17.
◆The phone you are using for remote operation has
touch tone dialling (DTMF), i.e. you hear different
tones when you press the keys.
Calling the answer machine and playing back
messages
~(Dial your own number) ¢while listening to your
announcement: press the 9key and enter the system
PIN
The following keys are used for operation:
Activating the answer machine
~(Enter your own number and allow the phoneto ring
until you hear the message: "Please enter PIN") ¢~
enter system PIN
Your answer machine is activated. It tells you how
much memory time is left. The messages are now
played back. The answer machine cannot be deacti-
vated remotely.
Locating a handset
("paging")
You can locate your handset using the base station.
◆Briefly press the registration/paging key on the
base station (¢page 1).
◆All handsets will ring simultaneously ("paging"),
even if the ringer tones are deactivated.
End paging: briefly press the registration/paging key
on the base station (¢page 1) or the talk key con
a handset.
Registering handsets
You can register up to four handsets on your base sta-
tion (Gigaset AS200) recommended).
For automatic registration of handsets to
Gigaset AS200/AS200A ¢page 5.
Manual registration of handsets to
Gigaset AS200/AS200A
Registration takes approx. 1 minute.
De-registering handsets
Handsets can only be de-registered by resetting the
base station to its default settings. This will also reset
other settings ¢page 11.
If you have only registered handsets for other GAP-
compatible devices, these can only be de-registered
with a hardware reset ¢page 11.
Using several handsets
Making internal calls
Internal calls are free calls to other handsets that are
registered to the same base station.
To make a call to other handsets, press
◆INT ¢~(1...4, enter internal number of the
handset), the handset is called or
◆INT ¢star key P, all handsets are called.
When a participant answers you can speak to them.
To end the call, press the end call key a.
AGo to the start of the current message.
Press twice to go back to the previous mes-
sage.
BStop playback. Press again to resume.
3Skip to next message.
0delete current message.
Please note:
Each additional handset must be registered on the
base station in order for it to work properly!
1. On the handset
MENU ¢Settings ¢OK ¢Handset ¢OK
¢Register HS ¢OK ¢Enter the system PIN of the
base station (default is 0000) ¢OK.
Registering flashes in the display.
2. On the base station
Within 60 seconds of entering the system PIN, press
and hold the registration/paging key (¢page 1)
(min. 3 seconds).

11
AS200-AS200A / GRC EN / A31008-M2208-T101-1-8U19 / main.fm / 12.11.2010
Internal consultation call/connecting
a call
You are in conversation with an external participant.
Press the INT key and call one or all handsets. The
external participant hears the hold music.
◆Before the internal participant has answered,
press the end call key a; the call is diverted to the
participant who answers the call.
◆After the internal participant has answered, you
can talk to him. Press the end call key a; the call is
diverted, or press the display key ”; you are
reconnected to the external participant.
Listening in to an external call
You are conducting an external call. An internal par-
ticipant can listen in on this call and take part in the
conversation (conference).
Precondition: The Listening in function must be acti-
vated.
Activating/deactivating listening in
MENU ¢Settings ¢OK ¢Base ¢OK
¢Listening in ¢OK (‰= on)
Internal listening in (conference)
You want to listen in to an existing external call.
Press and hold the ckey. You can listen in to the call.
All participants hear a signal tone.
To end: press the end call key a. All participants hear
a signal tone.
If the first internal participant presses the end call key
a, the handset that has "listened in" remains con-
nected to the external participant.
Setting the alarm clock
Activating/deactivating the alarm clock
MENU ¢Alarm Clock ¢OK ¢Activation
¢OK (‰= on)
When activated:
¢Set the wake-up time ¢OK
When the alarm clock rings, press any key to switch it
off for 24 hours. If the alarm clock is set, the wake-up
icon lwill appear on the screen and the wake-up
time will be displayed instead of the date.
Setting the wake-up time
MENU ¢Alarm Clock ¢OK ¢Wake-up time
¢OK
Enter the wake-up time in hours and minutes, then
press OK.
Phone settings
For details on how to set audio settings, see Menu
tree ¢page 16.
For details on how to set the system PIN on the base
station, see the Menu tree ¢page 17.
Changing the display language
MENU ¢Settings ¢OK ¢Handset ¢OK
¢Language ¢OK ¢select the language ¢OK
The current language is indicated by ‰ .
If you accidentally choose a language you do not
understand:
MENU ¢4 21 (press the keys one after the other)
Select the correct language with uand press OK.
Resetting the handset
You can reset individual settings and changes that
you have made. Entries in the directory, the calls list
and the handset's registration to the base station will
be retained.
MENU ¢Settings ¢OK ¢Handset ¢OK
¢Reset Handset ¢OK
Cancel the reset with a.
Restoring the base station to the
factory settings
When restoring factory settings:
◆All handsets are de-registered
◆Individual settings are reset
◆All lists are deleted
◆The system PIN is reset to the original code 0000
Only the date and time are retained.
Software reset
MENU ¢Settings ¢OK ¢Base ¢OK
¢Base Reset ¢OK
Hardware reset
Disconnect the power cord from the base station.
Hold down the registration/paging key (¢page 1)
on the base station while reconnecting the power
cable to the base station. Release the key after
approximately 5 seconds.
Repeater mode
With a repeater you can increase the range of your
base station. You will need to activate repeater mode
(¢page 17). Repeater mode and Eco mode or Eco
mode+ (¢page 1) cancel each other out.

12
AS200-AS200A / GRC EN / A31008-M2208-T101-1-8U19 / main.fm / 12.11.2010
Operating the base station on
the PABX
The following settings are only necessary if your PABX
requires them, see the user guide for your PABX.
When entering the digits, enter them slowly one after
the other.
Changing the dialling mode
MENU ¢4 I O 1 1 ¢The number for the set dial-
ling mode flashes: 0 = touch tonedialling (DTMF);1= dial
pulsing (DP) ¢enter number ¢OK.
Setting recall
MENU ¢4 I O 1 2 ¢The number for the current
recall flashes: 0= 80 ms; 1= 100 ms; 2= 120 ms;
3= 400 ms; 4= 250 ms; 5= 300 ms; 6 = 600 ms;
7= 800 ms ¢enter number ¢OK.
Changing pause after line seizure
You can set the length of the pause inserted between
pressing the talk key cand sending the phone
number.
MENU ¢4 I O 1 O ¢The number for the current
pause length flashes: 1 = 1 sec.; 2= 3 sec.; 3= 7 sec.
¢enter number ¢OK.
Changing the pause after the recall key
MENU ¢4 I O 1 4 ¢The number for the current
pause length flashes: 1= 800 ms; 2= 1600 ms;
3 = 3200 ms ¢enter number ¢OK.
Appendix
Entering letters/characters
Press the relevant key the number of times indicated.
Briefly press the hash key #to switch from "Abc" to
"123" mode, from "123" to "abc" mode and from "abc"
to "Abc" mode.
Standard characters
1) Space
Greek
1) Space
1x 2x 3x 4x 5x 6x 7x 8x 9x 10x11x12x13x14x
11£$¥¤
2a b c 2 ä á à â ã ç
Id e f 3 ë é è ê
4gh i 4 ï í ì î
5j k l 5
Lm n o 6 ö ñ ó ò ô õ
Mp q r s 7 ß
Nt u v 8 ü ú ù û
Ow x y z 9 ÿ ý æ ø å
Q. , ? ! 0 + - : ¿ ¡ " ’ ; _
P* / ( ) < = > %
#Abc
-->
123
123
-->
abc # @ \ & §
1x 2x 3x 4x 5x 6x 7x 8x 9x 10x 11x 12x
11 £ $
2Α Β 2 A B C
IΔ Ε Φ 3 D E F
4Γ Η Ι 4 G H I
5Κ Λ 5 J K L
LΜ Ν Ο Ω 6 M N O
MΠ Ρ Σ Ψ 7 P Q R S
NΘ Τ 8 T U V
OΖ Ξ Υ χ9 W X Y Z
Q. , ? ! 0 + - : " ’ ; _
P* / ( ) < = > %
#ABC
-->
123 # @ \ & §
1)
1)

13
AS200-AS200A / GRC EN / A31008-M2208-T101-1-8U19 / main.fm / 12.11.2010
Specifications
Recommended batteries
Technology: Nickel-metal-hydride (NiMH)
Size: AAA (Micro, HR03)
Voltage: 1.2 V
Capacity: 400–800 mAh
We recommend the following types of battery:
◆GP 550/700 mAh
◆Yuasa Phone 700/800 mAh
◆Peacebay 550/650 mAh
(Valid at the time of going to press)
The handset is supplied with recommended batter-
ies.
Base station power consumption
General specifications
Questions and answers
If you have any queries about the use of your
telephone, visit our website at
www.gigaset.com/service
for 24-hour support. The table below contains a list of
common problems and possible solutions.
In standby mode
– Handset in base station
– Handset outside base station
approx. 1.3 W
approx. 1.3 W
During a call approx. 1.5 W
DECT standard is supported
GAP standard is supported
Range up to 300 m outdoors
up to 50 m indoors
Base station power supply 230 V ~/50 Hz
Environmental conditions
in operation
+5°C to +45°C, 20% to
75% relative humidity
Problem Cause Solution
Nothing
appears in the
display.
The handset is not
switched on.
The batteries are
flat.
Press the end call
key afor approx.
5seconds or place the
handset in the base
station.
Charge or replace the
batteries.
No wireless
connection to
the base sta-
tion, Base
flashes in the
display.
The handset is out-
side the range of
the base station.
The handset is not
registered.
The base station is
not turned on.
Move the handset
closer to the base
station.
Register the handset
¢page 10.
Check the mains
connector on the base
station ¢page 3.
You cannot
hear a ringer/
dialling tone
from the fixed
line network.
The phone cord
supplied has not
been used or has
been replaced by a
new cord with the
wrong jack con-
nections.
Please always use the
phone cord supplied or
ensure that the
pin connections are
correct when purchas-
ing from a retailer:
3-4 assignment of
telephone leads/EURO
CTR37.
Error tone
sounds after
system PIN
prompt.
PIN forgotten.
You have entered
the wrong
system PIN.
Reset the system PIN to
the default 0000
¢page 11.
All handsets are de-
registered. All settings
are reset. All lists are
deleted.

14
AS200-AS200A / GRC EN / A31008-M2208-T101-1-8U19 / main.fm / 12.11.2010
Customer Service & Assistance
You have questions? As a Gigaset customer, you can take advantage of our comprehensive service offerings. You
can find help quickly in this User Manual and in the service pages of our Gigaset online portal.
Please register your phone right after purchase on www.gigaset.com/gr/service
thus enabling us to provide you even with better service in case of questions or in case of a warranty claim. Your
personal user account enables you to directly contact our customer service by email.
In our constantly updated online service on www.gigaset.com/gr/service you can find:
◆Extensive information about our products
◆FAQ compilations
◆Keyword search to help find topics quickly
◆Compatibility database: Find out which base stations and handsets can be combined.
◆Product comparison: Compare the features of several products with each other.
◆Downloads for user manuals and current software updates
◆E-mail contact form to our customer service
Our service representatives are available on the telephone for more advanced questions or in-person consulta-
tion.
Service Greece 801 1000 500
(0.026 € per minute from the Greek phone network. For calls from mobile phone networks, other prices may
apply.)
Please note that if the Gigaset product is not sold by authorised dealers in the national territory the product may
not be fully compatible with the national telephone network. It is clearly specified on the box near the CE mark
as well as on the bottom of the base station for which country/countries the equipment has been developed. If
the equipment is used in a manner inconsistent with this advice or with the instructions of the manual and on
the product itself, this may have implications on the conditions for warranty or guarantee claims (repair or
exchange of product).
In order to make use of the warranty, the product purchaser is asked to submit a receipt which proves the date
of purchase (date from which the warranty period starts) and the type of goods that have been purchased.

15
AS200-AS200A / GRC EN / A31008-M2208-T101-1-8U19 / main.fm / 12.11.2010
Authorisation
This device is designed for the analogic telephone
connection in the greek telephone net.
Gigaset Communications GmbH hereby declares that
the phone described in this user guide is in compli-
ance with the essential requirements and other rele-
vant provisions of European Directive 1999/5/EC
(R&TTE).
If you require a copy of the original, visit the website:
www.gigaset.com/docs.
Guarantee Certificate
Without prejudice to any claim the user (customer)
may have in relation to the dealer, the customer shall
be granted a manufacturer's Guarantee under the
conditions set out below:
◆In the case of new devices and their components
exhibiting defects resulting from manufacturing
and/or material faults within 24 months of
purchase, Gigaset Communications shall, at its
own option and free of charge, either replace the
device with another device reflecting the current
state of the art, or repair the said device. In
respect of parts subject to wear and tear (e.g.,
batteries, keypads, casings), this warranty shall
be valid for six months from the date of purchase.
◆This Guarantee shall be invalid if the equipment
defect is attributable to improper treatment and/
or failure to comply with information contained
in the user manuals.
◆This Guarantee shall not extend to services per-
formed by the authorised dealer or the customer
themselves (e.g. installation, configuration, soft-
ware downloads). User manuals and any soft-
ware supplied on a separate data medium shall
be excluded from the Guarantee.
◆The purchase receipt, together with the date of
purchase, shall be required as evidence for invo-
king the Guarantee. Claims under the Guarantee
must be submitted within two months of the
Guarantee default becoming evident.
◆Ownership of devices or components replaced
by and returned to Gigaset Communications
shall vest in Gigaset Communications.
◆This Guarantee shall apply to new devices
purchased in the European Union. TheGuarantee
is issued by Gigaset Communications Austria
GmbH, Businesspark Marximum Objekt 2 /
3.Stock, Modecenterstraße 17, 1110 Vienna,
Austria.
◆Any claims that differ from or extend beyond
these mentioned in this manufacturer’s warranty
shall be excluded, except from cases expressly
specified in the applicable law. (In no event shall
Gigaset Communications be liable for any loss of
business, profits or data, additional software loa-
ded by the customer or other information. The
customer shall also bear the responsibility for the
creation of backup copies of their files. The limita-
tion of liability shall not apply if and to the extent
liability is mandatory under the applicable law,
e.g. according to product liability law or in the
event of intentional misconduct, severe negli-
gence, personal injury, damage to parts of the
human body or to personal health, or in case of
violations of conventional obligations. However,
the claims for damages related to violation of
conventional obligations shall be limited to pre-
dictable damages, representative of such con-
ventions, as long as there is no intention or severe
negligence, personal injury, damage to parts of
the human body or to personal health, according
to the product liability law.)
◆The duration of the Guarantee shall not be exten-
ded by services rendered under the terms of the
Guarantee.
◆Insofar as no Guarantee default exists, Gigaset
Communications reserves the right to charge the
customer for replacement or repair.
◆The above provisions do not imply a change in
the burden of proof to the detriment of the
customer.
To invoke this Guarantee, please contact the Gigaset
Communications telephone service. The relevant
number is to be found in the accompanying user
guide.

16
AS200-AS200A / GRC EN / A31008-M2208-T101-1-8U19 / main.fm / 12.11.2010
Menu tree
Your phone has an extensive range of features. These
are offered in the form of menus.
To select a function while the phone is in idle status,
press MENU (open menu), use the tand vkeys to
scroll to the function you require and press OK to con-
firm.
To return to idle status: press and hold the akey.
As an alternative to selecting functions using the t
and vbuttons, you can also enter the digit combina-
tion that is in front of the function in the menu tree.
For setting the time and date, for example:
MENU ¢4 1 ¢OK
1Alarm Clock
1-1 Activation Activating/deactivating the alarm clock
1-2 Wake-up time Input format: HHMM
2Audio Settings
2-1 Handset Volume Can be set to one of 3 levels
2-2 Ringer Volume 5 levels + "crescendo" available
2-3 Ringer Melody 2-3-1 External Calls 10 ringer melodies available for external calls
2-3-2 Internal Calls 10 ringer melodies available for internal calls
2-3-3 Alarm Clock 10 ringer melodies available for alarm clock
2-4 Advis. Tones Activate/deactivate
2-5 Battery Low 2-5-1 Off Warning tone to indicate bat-
tery is almost flat:
never
2-5-2 On always
2-5-3 During Call only during a call
3Voice Mail
3-1 Set Key 1
(all devices)
3-1-1 Netw. Mailbx Assign key 1with network mailbox and enter the network mailbox
number (in idle status, press and hold key 1to dial).
Netw. Mailbx: your network provider's answer machine; must be
requested separately. The network mailbox list can be displayed if your
network provider supports this function and if key 1has been assigned
with the network mailbox.
(Only devices
with answer
machine)
3-1-2 Answer Mach. Assign key 1with answer machine
(in idle status, press and hold to dial).
3-2 Answer Mach. Activating/deactivating the answer machine
3-3 Call Screening
3-3-2 Base You can use the loudspeaker on the base station to screen a message
that is being recorded.
3-4 Announcements 3-4-1 Rec announce ¢page 9
3-4-2 Play announce Play your announcement
3-4-3 Del announce Delete your announcement
3-5 Message Length 3-5-1 Maximum Do not limit the recording time for each call.
3-5-2 1 Minute Limit the recording time to 1 minute per call.
3-5-3 2 Minutes Limit the recording time to 2 minutes per call.
3-5-4 3 Minutes Limit the recording time to 3 minutes per call.

17
AS200-AS200A / GRC EN / A31008-M2208-T101-1-8U19 / main.fm / 12.11.2010
3-6 Ring Delay 3-6-1 Immediately Call is answered immediately.
3-6-2 10 sec Call is answered after 10 seconds.
3-6-3 18 sec Call is answered after 18 seconds.
3-6-4 30 sec Call is answered after 30 seconds.
3-6-5 Auto If there are no new messages, the answer machine answers a call after
18 seconds. If new messages are present, the answer machine answers
a call after just 10 seconds.
4Settings
4-1 Date/Time Enter date (DDMMYY format), then time (HHMM format)
4-2 Handset 4-2-1 Language Set the display language ¢page 11
4-2-2 Auto Answer Automatically activate/deactivate auto answer ¢page 7
4-2-3 Register HS Manually register the handset ¢page 10
4-2-4 Reset Handset Reset the handset ¢page 11
4-3 Base 4-3-1 Audio Settings
(AS200A)
4-3-1-1 Ringer Volume 5 level settings + "crescendo" + "off"
4-3-1-2 Ringer Melody 10 selectable melodies
4-3-2 Call list type 4-3-2-1 Missed Calls ¢page 8
4-3-2-2 All Calls ¢page 8
4-3-3 System PIN Change system PIN (default is 0000)
4-3-4 Base Reset Restore factory settings ¢page 11
4-3-5 Additional 4-3-5-1 Repeater activate/deactivate ¢page 11
4-3-5-2 Eco Mode+ activate/deactivate ¢page 2
4-3-5-3 Eco Mode activate/deactivate ¢page 2
4-3-6 Listening in Activate/deactivate the function ¢page 11
4-3-7 Preselection 4-3-7-1 Presel. Number Network provider dialling code, should
be inserted automatically before the
dialled phone number.
4-3-7-2 With Preselect First digits of the dialling codes, should
be dialled with preselection.
4-3-7-3 Without Presel First digits of dialling codes, should be
dialled without preselection.

18
AS200-AS200A / GRC EN / A31008-M2208-T101-1-8U19 / main.fm / 12.11.2010
Issued by
Gigaset Communications GmbH
Frankenstr. 2a
D-46395 Bocholt
Manufactured by Gigaset Communications GmbH
under trademark license of Siemens AG.
As of 1 Oct. 2011 Gigaset products bearing the
trademark "Siemens" will exclusively use the
trademark "Gigaset".
© Gigaset Communications GmbH 2011
All rights reserved. Subject to availability.
Rights of modification reserved.
www.gigaset.com
This user guide is made from 100% recycled paper.