Siemens TS1 User manual

Siemens TS1 Standard Push Button
For EZ Rebuild Kits Or Tech Support, Contact 1-800-SCORE-OK or Visit www.ScoreDental.com
Required
Tools
SI01KIT
107-2057
Step 1
After reviewing the training video and step-by-step
instruction sheet, install the blank bur provided with
your EZ Press and check to make sure that the
spindle/chuck is holding the bur. If bur pulls out call
Score for replacement spindle/chuck.
Siemens TS1 Standard PB is a tradename and is not affiliated with Score Intl.
Bearing Kit Turbine
Rear
Bearing
Front
Bearing
CAUTION: Could result in damage to parts
!
WARNING: Could result in handpiece malfunction
!
Spindle
DR70B3L
Step 2
Loosen headcap using appropriate cap wrench and
remove turbine. If head cap and turbine come out
together, separate and set head cap aside. Place Insert B
underneath the Spindle Ram on the left side of the press.
Place the turbine in the center of Insert B with the bur going
down through the hole in the center.
Step 3
Locate the EZ Push-Button Protector that was included
with the press. Insert the skinny end up into the Spindle
Ram on the left and hold in place with your fingers.
Slowly pull the handle down until the protector meets
the rear of the spindle and covers the button.
Step 4
Make sure everything is aligned and pull down or tap the
handle firmly to push out the spindle/chuck and disassemble
the turbine. The spindle/chuck will fall into the tray below.
Step 5
The old bearings and impeller will remain sitting on Insert B.
Discard the bearings and inspect the impeller any chips,
cracks or worn blades. If the impeller has any damage call
Score for a replacement.
Step 6
Place Insert #1 underneath the Bearing Ram on the right
side of the press. Open your rebuild kit and pick up one of
the bearings. Pick up the spindle/chuck and hold it so the
bur points up. Drop the bearing over the bur so the silver
shielded faces down, away from the bur and the black side
faces up.
HSM855-70822
107-7037
Headcap
TSP525
DR70B3L
Genuine EZ
Rebuild KitTM by
1-800-726-7365
EZ
Turbine by
Install
O-ring
HSM165
O-ring
HSM165
EZ Push-Button
Protector
(EZ301PBP)
Blank Bur
(HMW271-1)
Insert B
(EZ301BAIB)
B4
Insert 4
Cap Wrench
TST903
Impeller
HSM343

Siemens TS1 Standard Push Button
REPDGM/SM002-Rev A-4/24/2006
Step 10
Using an explorer remove the old o-rings from the head
and head cap. Clean the head and head cap with
cleaner and a cotton swab, making sure to remove any
debris. Use your explorer to install the new o-rings into the
head and head cap. Seat the rebuilt turbine into the head
cap and install into head. Tighten cap down completely
and make sure the bur rotates and releases the bur, then
hook up and run.
Step 9
Locate the front bearing and drop it over the bur so
the silver shielded side faces up and the black side
faces down towards the impeller. Repeat pressing
process until bearing comes to a stop when it reaches
the impeller. If the bearing is riding loosely on the spindle
use EZ Tight to hold it on.
Step 11
If the headcap heats up or you feel resistance while
testing remove the turbine and re-inspect the head
with an explorer to make sure no debris was overlooked.
If clean then call for Tech Support.
Step 8
Locate the impeller and repeat process, making sure that
with the bur facing away from you the air would turn the
impeller clockwise or the blades slant left at the 12 o’clock
position. Press impeller until it stops at the bearing.
Step 7
Once the bearing is in position feed the blank bur up
into the bearing ram on the right side of the press. Slowly
pull down on the handle while holding the turbine in
place until the rear of the spindle meets and is aligned
with the hole in the center of Insert #1. Gently press
bearing down the spindle until it stops at Insert #1. If the
bearing is riding loosely on the spindle use EZ Tight to
hold it on.
!