Siemens 9510 User manual

© 2004 Siemens Energy & Automation. All rights reserved. The information in this document is believed to be accurate at the time of publication, however, Siemens Energy & Automation assumes no responsibility for errors which may
appear here and reserves the right to make changes without notice. ION is a registered trademark of Power Measurement Ltd. All other trademarks are property of their respective owners. Revision Date: July 19, 2004
9510 and 9610 I/O Card
This document describes how to install, configure, and verify the operation of the
optional Input/Output card (“I/O card”), available for your 9510 / 9610 meter. It
supplements your meter’s Installation Guide and User’s Guide.
In This Document
 Installation and Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Preparing the Meter for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installing the I/O Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Connecting to the I/O Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
 Verifying Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Additional Information
9510 / 9610 User’s Guide
9510 / 9610 Installation Guide
ION Reference

Installation and Wiring 9510 and 9610 I/O Card
Page 2
Installation and Wiring
DANGER
During normal operation of the meter, hazardous voltages are present which can cause severe injury or
death. These voltages are present on the terminal strips of the device and throughout the connected
potential transformer (PT), current transformer (CT), status input, relay, and control power circuits. Only
qualified, properly trained personnel should perform installation and servicing.
The standard model I/O card has 8 digital inputs. Depending on what you ordered,
the I/O card will also contain either 4 analog inputs, or 4 analog outputs, or both.
Check the label on the I/O card for your I/O specifications.
AI4 AO4
AI3 A03
AI2 A02
AI1 AO1
Rear View of Meter
Analog connections from
external transducers
0to20mAor0-1mA
Analog Connections to
analog transducers
0 to 20mA: 500 Ohm load Max
-1 to 1mA: 10k Ohm load Max
Digital connections from
external relays or pulse counter
50 VDC Max
External Dry Contacts
(polarity for SSR
contacts shown)
AWG 12 to 14 (3.3 to 2.1 mm ) recommended; wire sizes will vary depending on application
2
DI1
DI2
DI3DI4DI5DI6
DI7
DI8
DICOM
AI1
+-AO1
OUTCOM
I/O C ARD
Standard I/O Locations

9510 and 9610 I/O Card Preparing the Meter for Installation
Page 3
Preparing the Meter for Installation
The following steps should be taken before inserting an I/O card into an
9510 / 9610 meter:
CAUTION
The components inside the meter are extremely sensitive to electrostatic discharge. Wear an anti-static
wrist strap at all times when working inside the unit. Failure to use proper equipment during servicing will
void the meter’s warranty.
1. Turn off all power to the meter.
2. Open all PT fuses (or direct voltage input fuses). Close all CT shorting blocks.
3. Disconnect the Line and Neutral (or DC power) wires from the Control Power
inputs of the unit.
4. Disconnect all other wiring (or power off all other circuits) which may present
potentially hazardous voltage levels to the unit, such as connections to the relay
outputs, status inputs, etc.
5. Ensure that all cables still connected to the meter are NOT live.
Installing the I/O Card
The I/O card consists of a circuit board with an attached polarized CHAMP
connector on the component side. Follow these steps to install the I/O card:
1. If present, remove the plastic tab that seals the I/O card’s cover plate to the
meter. Use the Phillips screwdriver to remove the plate’s two screws, then
remove the plate.
2. Hold the I/O card by the sides and slide it into the base unit with the component
side facing up. Slide the edge of the circuit board down the slots along each side
of the chassis.
3. Align the CHAMP connector with the socket and press the I/O card firmly into
place. The socket and the connector are polarized, so the pins in the connector
will not fit into the socket if the card is not oriented correctly. The I/O card is
securely inserted into the socket when the backplate of the I/O card meets the
chassis of the meter.
4. Ensure the cover meets the chassis of the base unit. Use the Phillips screwdriver
to replace the two backplate screws with their lock-washers. They must be
installed firmly to preserve transient immunity.
5. Reinstall the Line and Neutral (or DC power) wiring to the Control Power inputs
of the unit.
6. Reconnect all other wiring (or re-enable all other circuits). Close the PT fuses (or
direct voltage input fuses), and open the CT shorting blocks.
7. Turn on power to the meter and verify the correct operation of the unit.

Connecting to the I/O Card 9510 and 9610 I/O Card
Page 4
Connecting to the I/O Card
See the 9510 / 9610 Installation Guide for detailed instructions.
Verifying Operation
Checking Status on Front Panel
The 9510 / 9610 meter’s onboard status inputs and digital outputs can be
monitored using the D Inputs and D-Output softkey items. Two additional
softkey items have been added to monitor the status and values provided by the
I/O card’s Analog Input and Analog Output ports. These menus are located in the
main softkey list, and are named DI-I/O and Anlg-I/O.
WinPM.Net Vista Diagram
The meter’s Vista screens have provisions for monitoring and altering the states of
each I/O port.
Testing Analog I/O Operation
Most analog devices (such as dial-type gauges) connected to your analog input
and output ports allow you to see whether the port is delivering current. If your
connected device cannot help you determine the port's operation, follow these
steps:
1. Ensure that the meter is properly configured.
2. Disconnect supply power from your meter and make sure that no static charge
remains in the circuit.
3. Place an ammeter in series with the port.
4. Power up the meter, and measure the current.
If your analog ports are not producing the output current as expected, contact
Customer Service.