Siemens SINAMICS G120 Administrator guide

Screening plate fitting PM240-2 PT
M5,
3.5 Nm
Screening plate fitting PM240-2
abovebelow
Ø 6 mm
Mounting frame
fixing hole
FSC
e
e
aaa
aaa
d
c
b
Mounting frame
fixing hole
Mounting frame
fixing hole
Mounting frame
fixing hole
Ø 6 mm
aa aa
d
FSA/FSB
e
e
c
b
IP20 Units
Frame
size
Dimensions (mm)
Distances
(mm)1)
Fixings
Drill pattern
(mm)
Height
Width
Depth
Max.
depth
with C U
and OP
Above
Below
S crew
Tightening
Torque
(Nm)
a
b
c
With
S hielding
Plate
FSA
196
276
73
165
250
80
100
M4
2.5
186
62.3
6
FSB
291
370
100
165
250
80
100
M4
2.5
281
80
6
FSC
355
432
140
165
250
80
100
M4
3.0
343
120
6
1) The Power Modules can be mounted side-by-side. Due to tolerance reasons, we recommend a lateral
distance of about 1 mm
P T Units
FSA
238
322
126
171
256
80
100
M5
3.5
103
106
88
198
27
FSB
345
430
154
171
256
80
100
M5
3.5
147.5
134
116
304
34.5
FSC
411
500
200
171
256
80
100
M5
3.5
123
174
156
365
30.5
1)
Cable lengths, using
EMI Level (Emission)
Scr eened cables, filtered units (class A)
50m
Sec ond Environment, C2
Scr eened cables, unfiltered units,
50m
EMI St andard not fullfilled
Unscree ned cables, filtered or unfiltered units
100 m
EMI St andard not fullfilled
36.5
ac
b
FSA
a c
b
FSB/FSC
IP20 Units
FSA
196
276
73
165
250
80
100
M4
2.5
186
62.3
6
FSB
2922
370
100
165
250
80
100
M4
2.5
281
80
6
FSC
355
432
140
165
250
80
100
M5
3.5
343
120
6
1)
1)
P T Units
Frame
size
Dimensions (mm)
Distances
(mm)1)
Fixings
Drill patt
Height
Width
Depth
Max.
depth
with C U
and OP
Above
Below
S crew
Tightening
Torque
(Nm)
a
With
S hielding
Plate
T1
T2
FSA
238
322
126
171
117.7
53.1
256
80
100
M5
3.0
103
FSB
345
430
154
171
117.7
53.1
256
80
100
M5
3.0
147.5
FSC
411
500
200
171
117.7
53.1
256
80
100
M5
3.0
123
1) The Power Modules can be mounted side-by-side. Due to tolerance reasons, we recommend a la teral distance o
Cable lengths, using
EMI Level (Emission)
Scr eened cables, filtered units (class A)
50m
Sec ond Environment, C2
Scr eened cables, unfiltered units,
50m
EMI St andard not fullfilled
Unscree ned cables, filtered or unfiltered units
100 m
EMI St andard not fullfilled
接触带电部件会引发生命危险接触带电部件会引发生命危险接触带电部件会引发生命危险接触带电部件会引发生命危险
本设备会传导危险电压。
接触带电部件可能会造成人员重伤，甚至是死亡。
务必遵循变频器手册中的说明。
In questo apparecchio sono presenti tensioni pericolose.
Il contatto con parti sotto tensione può provocare la morte o gravi lesioni.
Attenersi alle avvertenze contenute nei manuali del rispettivo convertitore.
Avvertenza
En el presente equipo hay aplicadas tensiones peligrosas.
Tocar piezas que están bajo tensión puede provocar lesiones corporales graves o
incluso la muerte.
Respete las indicaciones que se especifican en los manuales del convertidor
correspondiente.
Advertencia
L'appareil présente des tensions électriques dangereuses.
Tout contact avec des parties sous tension peut entraîner la mort ou des blessures
graves.
Respecter les consignes figurant dans les manuels du variateur concerné.
Attention
The present device conducts hazardous voltages.
Touching live components can result in death or severe injury.
Observe the notes in the manuals of the corresponding converter.
Warning
Das vorliegende Gerät führt gefährliche Spannungen.
Beim Berühren unter Spannung stehender Teile erleiden Sie Tod oder schwere
Körperverletzungen.
Beachten Sie die Hinweise in den Handbüchern des zugehörigen Umrichters.
Warnung
Cabinet
Seal
Mounting Frame
1
2
2
1
3
34
2
M4,
2.5 Nm
*A5E37968360*
Lebensgefahr durch Berührung unter Spannung stehende Teile
Danger de mort en cas de contact avec des pièces sous tension
Danger to life when live parts are touched
Peligro de muerte al tocar piezas bajo tensión Pericolo di morte per contatto con parti sotto tensione
警告警告警告警告
SINAMICS G120
Power Module PM240-2, FSA, FSB, FSC
Dimension and drill patterns PM240-2, IP20
T1 T2
The Power Modules can be mounted side-by-side. Due to tolerance reasons, we recommend a lateral
distance of about 1 mm.
The Power Modules can be mounted side-by-side. Due to tolerance reasons, we recommend a lateral distance of about 1 mm.
Tightening
torque
(NM)
Tightening
torque
(NM)
Max.
depth
with CU
and OP
Max.
depth
with CU
and OP
Below
Below
Above
Above
Width
Width
Depth
Depth
Screw a
a c d e
b
b
c
Screw
Edition: 04/2021
Frame
size
Frame
size
Dimensions (mm)
Dimensions (mm)
Height
Height
Air flow dis-
tances (mm) 1)
Drill pattern
(mm)
Drill pattern and cutouts
(mm)
Fixings
Fixings
A5E37968360 AC
Compact Operating Instructions
Drill patterns and dimensions PM240-2, Push-through Push-through mounting frame with
mounting sequence
Cutouts and drill patterns in
the cabinet wall for the
mounting frame
Siemens AG,
Digital Industries
Motion Control
Postfach 3180
91050 ERLANGEN
Germany
For detailed information, see PM240-2 Hardware Installation Manual:
Height
Width
Depth
Shield
plate
T1
T2
CU
OP
Height without shield
plate
Width
Depth
CU
OP
Shield
plate
118
118
118
53
53
53
without
shield
plate
with
shield
plate
without
shield
plate
with
shield
plate
Declaration of Conformity:
The Declaration of Conformity can be found at the following link:
https://support.industry.siemens.com/cs/ww/en/ps/13224/man
https://support.industry.siemens.com/cs/ww/en/ps/13225/cert
FSA: 6SL3260-6AA00-0DA0
FSB: 6SL3260-6AB00-0DA0
FSC: 6SL3260-6AC00-0DA0
It’s recommended to use the optional mounting
frame to install the push-through Power Module in
a cabinet. This optional mounting frame is designed
in conjunction with the supplied seal to easily
maintain an IP55 rating of the enclosure (the seal is
delivered with the Power Module). If the Power
Module is mounted without using the optional
mounting frame, it is the user’s responsibility to
ensure that the correct IP protection rating is
reached.
Air flow dis-
tances (mm) 1)
Air flow distances

Insert CU Remove CU
Fitting CU to PM
Tightening torques:
SINAMICS G120
Power Module PM240-2, FSA, FSB, FSC
Mains, Motor and Brake terminals
The Power Modules are fitted with detachable terminals. It can
be removed from the Power Module by pressing the release
catch. The connectors are not interchangeable.
FSA: 0.5 Nm ( 4.5 lbf.in)
FSB: 0.6 Nm ( 5.5 lbf.in)
FSC: 1.3 Nm (12 lbf.in)
① Mains connector
② Motor connector
③ DC Link connector
④ Release catch
Cable cross sections
FSA: 1.5 … 2.5 mm216 … 14 AWG
FSB: 1.5 … 6 mm216 … 10 AWG
FSC: 6 … 16 mm210 … 6 AWG
150 % for 3 s
110 % for 57 s
200 % for 3 s
150%for 57 s
100 % for 240 s 100 % for 240 s
Permissible overload for operation
Screened cables, filtered units (class A) Second Environment, C2
EMI Standard not fulfilled
EMI Standard not fulfilled
Screened cables, unfiltered units
Unscreend cables, filtered or unfiltered units
according to “Low Overload“ (LO)
Overloads
Permissible overload for operation
according to “High Overload“ (HO)
HO base load: 100 % HO power
100 % HO current
LO base load: 100 % LO power
100 % LO current
%
300240
1801200
100
200
60t[s]
%
300240
1801200
100
150
60t[s]
For United States / Canadian installations (UL/cUL): In order that the system is UL/cUL-compliant, use
UL/cUL-certified J-type fuses. Use 75° C copper wire only.
Additional requirements for Canadian compliance:
400 V supply:
Transient surge suppression must be installed on the line side of this equipment and shall be rated 480 V
(phase to ground), 480 V (phase to phase), suitable for overvoltage category III and shall provide protection
for a VPR maximum of 2 kV, type 1 or type 2 SPD application.
200 V supply:
Transient surge suppression must be installed on the line side of this equipment and shall be rated 240 V
(phase to ground), 240 V (phase to phase), suitable for Overvoltage Category III and shall provide protection
for a VPR maximum of 2 kV, type 1 or type 2 SPD application.
CAUTION - Cable cross-section for grounding: The earth cable must be at least as big as the power cables.
Siemens AG,
Digital Industries
Motion Control
Postfach 3180
91050 ERLANGEN
Germany
Edition: 04/2021
50m
50m
100m
3 AC 380V… 480V± 10%up to 2000m installation
altitude. 1 AC / 3 AC 200 V... 240 V± 10%up to 2000 m installation altitude.
3 AC 0V… input voltage * 0.95
50Hz … 60Hz, ± 3 Hz
<
kW
hp
A
kW
hp
A
A
0.55
0.75
1.7
0.37
0.50
1.3
2.3
FSA
(4A)
10A
0.75
1.00
2.2
0.55
0.75
1.7
2.9
FSA
(4A)
10A
1.10
1.50
3.1
0.75
1.00
2.2
4.1
FSA
(6 A)
15 A
1.50
2.00
4.1
1.10
1.50
3.1
5.5
FSA
(10A)
15 A
2.20
3.00
5.9
1.50
2.00
4.1
7.7
FSA
(10A)
15 A
3.00
4.00
7.7
2.20
3.00
5.9
10.1
FSA
(16 A)
15 A
4.00
5.00
10.2
3.00
4.00
7.7
13.3
FSB
(20 A)
35 A
5.50
7.50
13.2
4.00
5.00
10.2
17.2
FSB
(25 A)
35 A
7.50
10.00
18.0
5.50
7.50
13.2
22.2
FSB
(35 A)
35 A
11.00
15,00
26.0
7.50
10.00
18.0
32.6
FSC
(50A)
50A
15.00
20.00
32.0
11.00
15.00
26.0
39.9
FSC
(50A)
50A
3.00
4.00
7.7
2.20
3.00
5.9
10.1
FSA
(16 A)
15 A
7.50
10.00
18.0
5.50
7.50
13.2
22.2
FSB
(35 A)
35 A
15.00
20.00
32.0
11.00
15.00
26.0
39.9
FSC
(50A)
50A
0.55
0.75
3.2
0.37
0.50
2.3
7.5
FSA
(10A)
15 A
0.75
1.00
4.2
0.55
0.75
3.2
9.6
FSA
(16 A)
15 A
1.10
1.50
6
0.75
1.00
4.2
13.5
FSB
(20 A)
35 A
1.50
2.00
7.4
1.10
1.50
6
18.1
FSB
(25 A)
35 A
2.20
3.00
10.4
1.50
2.00
7.4
24.0
FSB
(35 A)
35 A
3.00
4.00
13.6
2.20
3.00
10.4
35.9
FSC
(50A)
50A
4.00
5.00
17.5
3.00
4.00
13.6
43.0
FSC
(63 A)
50A
5.50
7.50
22.0
4.00
5.00
17.5
28.6
FSC
(40A)
50A
7.50
10.00
28.0
5.50
7.50
22.0
36.4
FSC
(50A)
50A
0.75
1.00
4.2
0.55
0.75
3.2
9.6
FSA
(16 A)
15 A
2.20
3.00
10.4
1.50
2.00
7.4
24.0
FSB
(35 A)
35 A
4.00
5.00
17.5
3.00
4.00
13.6
43.0
FSC
(63 A)
50A
5.50
7.50
22.0
4.00
5.00
17.5
28.6
FSC
(40A)
50A
7.50
10.00
28.0
5.50
7.50
22.0
36.4
FSC
(50A)
50A
Feature Specification
PM240-2, Push-through units, 3 AC 380 V ... 480 V
PM240-2, Built-in units, 3 AC 380 V ... 480 V
PM240-2, Built-in units, 1 AC/3 AC 200 V ... 240 V
PM240-2, Push-through units, 3 AC 200 V ... 240 V
PM240-2, Push-through units, 1 AC/3 AC 200 V ... 240 V
PM240-2, Built-in units, 3 AC 200 V ... 240 V
Low values
Power
Cable lengths, using EMI level (Emission)
High values
Power
Rated
(LO)
input
current
Output
current
Output
current
Frame
Size
Order No. *)
Siemens
3NA3804
3NA3801
3NA3803
3NA3803
3NA3803
3NA3805
3NE1814-0
3NE1814-0
3NE1815-0
3NE1815-0
3NE1803-0
3NE1803-0
3NE1803-0
3NE1802-0
3NE1802-0
3NE1803-0
3NE1817-0
3NE1817-0
3NE1817-0
3NE1817-0
3NE1817-0
3NE1818-0
3NE1818-0
3NE1817-0
3NA3805
Storage temperature
Shock
< LO base load input current
Short Circuit Current Rating
(SCCR)
3NA3805
3NA3805
3NA3804
6SL3210-1PE11-8_L1
6SL3210-1PE12-3_L1
6SL3210-1PE13-2_L1
6SL3210-1PE13-0_L0
6SL3210-1PE13-8_L0
6SL3210-1PE15-5_L0
6SL3210-1PE17-4_L0
6SL3210-1PE21-0_L0
6SL3210-1PE21-4_L0
6SL3210-1PE21-8_L0
6SL3210-1PE14-3_L1
6SL3210-1PE16-1_L1
6SL3210-1PE21-1_L0
6SL3210-1PE21-4_L0
6SL3210-1PE21-8_L0
6SL3211-1PE21-8_L0
6SL3210-1PE22-7_L0
6SL3210-1PC22-2_L0
6SL3211-1PC22-2_L0
6SL3210-1PC22-8_L0
6SL3211-1PC22-8_L0
6SL3211-1PB13-8_L0
6SL3211-1PB21-0_L0
6SL3211-1PB21-8_L0
6SL3210-1PE23-3_L0
6SL3211-1PE23-3_L0
6SL3210-1PE18-0_L1
6SL3211-1PE18-0_L1
UL, J-type
Line fuses
Compact Operating Instructions
Data regarding the power loss in accordance with Ecodesign Regulation
(EU) 2019/1781 and IEC 61800-9-2
You can find data regading power loss of our products on the Internet:
*) _: A = filtered unit, U = unfiltered unit
Screening methods
Line
cable
Motor cable
Control cable
Wire
straps
Braking resistor cable
Shielding brackets
https://support.industry.siemens.com/cs/ww/en/view/94059311
Bulit-in units (open type equipment): IP20
Push-through units: IP54/UL Type 12 when mounted on a flat surface of an enclosure
Interference emission: The devices are suitable for second environment category C2 in accordance with IEC 61800-3 if the following
conditions are fulfilled: The motor cable is a shielded cable with low capacitance and is not longer than 50 m. The pulse frequency does
not exceed 4 kHz, the current does not exceed the LO input value. For details, refer to the Hardware Installation Manual.
Interference immunity: The devices are suitable for second environment category C3
4 kHz. Can be increased in 2 kHz steps up to 16 kHz. Increasing the pulse frequencies leads to an output current reduction.
DC braking, Compound braking, Dynamic braking with integrated chopper plus external braking resistor
This equipment is capable of providing internal motor overload protection according to UL61800-5-1. The protection level is 115%, 230%
and 400% full load current of the equipment. This is adjusted via parameter P640 and assumes the equipment has had basic motor
commissioning for the motor used as described in the documentation.
Motor overload protection
LO operating temperature 1)
HO operating temperature 1)
Environmental rating
Electromagnetic compatibility
Braking methods
Suitable for use on a circuit capable of delivering not more than 100 kA rms symetrical amperes; 240/480 V AC maximum when protected
by Class J fuses.
Further suitable protective devices including the associated SCCR can be found in:
Power factor
Pollution For open type equipment according to pollution degree level 2. Protection against conductive pollutions required e.g. using an IP54
cabinet.
For enclosed type/push-through equipment according to pollution degree level 3.
200 V units: Uk 2 %, for lower values, a line reactor must be used.
400 V units: Uk 1 %, for lower values, a line reactor must be used.
Long-term storage in the transport packaging according to Class 1M2 of IEC 60721-3-1: Transport in the transport packaging according
to Class 2M3 of IEC 60721-3-2. See Hardware Installation Manual for detailed specifications.
Long-term storage in the transport packaging according to Class 1M2 of IEC 60721-3-1: Transport in the transport packaging according
to Class 2M3 of IEC 60721-3-2. See Hardware Installation Manual for detailed specifications.
Suitable for environmental class 3C2 according to IEC 60721-3-3 against damaging chemical substances
Up to 1000 m (3300 ft) without derating/ Up to 4000 m (13000 ft) with derating
95 % RH - non-condensing
0 °C ... 40 °C (32 °F ... 104 °F) without current derating / up to 60 °C (140 °F) with current derating
0 °C ... 50 °C (32 °F ... 122 °F) without current derating / up to 60 °C (140 °F) with current derating
- 40 °C ... + 70 °C (- 40 °F ... + 158 °F)
0.7 without line reactor; 0.85 with line reactor
0 Hz ... 550 Hz, depending on the control mode
https://support.industry.siemens.com/cs/ww/en/view/109782705
Vibration
Line impedance
Environmental conditions
Installation altitude above sea level
Line voltage
Output voltage
Input frequency
Output frequency
Irrush current
Pulse frequency (factory setting)
Humidity
1) according to UL, operation with temperatures > 50 °C (122 °F) is not permitted at all