Siemens OZW772 Series Training manual

s
Synco™, Synco™ living
Web server OZW772... V6.0
Commissioning instructions
OZW772.01
OZW772.04
OZW772.16
OZW772.250
CE1C5701en
2015-10-12 Building Technologies

2 / 176
Siemens Web server OZW772... V6.0 CE1C5701en
Building Technologies 2015-10-12
Siemens Switzerland Ltd
Building Technologies Division
International Headquarters
Gubelstrasse 22
6301 Zug
Switzerland
Tel. [phone]
www.siemens.com/buildingtechnologies
© Siemens Switzerland Ltd, 2009
Subject to change

3 / 176
Siemens Web server OZW772... V6.0 CE1C5701en
Building Technologies Table of contents 2015-10-12
Table of contents
1Overview ..............................................................................................7
1.1 Introduction............................................................................................7
1.2 Web Server display and operating elements...........................................9
1.3 User interface ......................................................................................10
1.3.1 User levels........................................................................................... 11
1.4 Symbols, notations, abbreviations........................................................12
1.4.1 Symbols ..............................................................................................12
1.4.2 Notations .............................................................................................13
1.4.3 Abbreviations.......................................................................................13
2 Commissioning..................................................................................14
2.1 Prerequisites........................................................................................14
2.2 Getting started .....................................................................................15
2.2.1 Turn on Web Server.............................................................................15
2.2.2 Log into Web Server ............................................................................16
2.3 Administer user accounts.....................................................................18
2.4 Create device web pages.....................................................................20
2.5 Web Server settings.............................................................................23
2.5.1 Operating page settings "Time of day/date"..........................................23
2.5.2 Operating page "Faults current" ...........................................................24
2.5.3 Operating page "Settings" ....................................................................24
2.5.3.1 Web Server.............................................................................. 24
2.5.3.2 Time of day/date ...................................................................... 24
2.5.3.3 Communication........................................................................ 25
2.5.3.4 Message receivers................................................................... 28
2.5.3.5 System report........................................................................... 31
2.5.3.6 Consumption data.................................................................... 32
2.5.3.7 Energy indicator ....................................................................... 33
2.5.3.8 Trend ....................................................................................... 34
2.5.3.9 Faults....................................................................................... 34
2.5.3.10 Texts........................................................................................ 35
2.5.4 Operating page "Device information"....................................................35
2.6 Commission network components........................................................36
2.6.1 Access via portal..................................................................................36
2.6.2 Access via a local area network (LAN).................................................36
2.6.3 Access via direct connection................................................................37
2.7 Functional check..................................................................................39
2.8 Additional settings................................................................................41
2.9 Final steps ...........................................................................................42
2.9.1 Check faults.........................................................................................42
2.9.2 Final steps on Web Server...................................................................42
2.10 Supply state.........................................................................................43
2.11 Software updates.................................................................................43
3Remote access via portal ..................................................................44
3.1 Set up access via portal.......................................................................44
3.1.1 Portal and plant roles ...........................................................................48
3.2 Prevent connection to portal.................................................................48

4 / 176
Siemens Web server OZW772... V6.0 CE1C5701en
Building Technologies Table of contents 2015-10-12
4Operate using a web browser ...........................................................49
4.1 Overview ............................................................................................. 49
4.2 Operate the plant.................................................................................51
4.2.1 Operate Synco device..........................................................................51
4.2.2 Operate Web Server............................................................................51
4.2.3 Web Server diagnostics .......................................................................53
4.3 Faults ..................................................................................................56
4.3.1 Overview .............................................................................................56
4.3.2 Device faults........................................................................................56
4.4 File transfer .........................................................................................58
4.5 Operation with ACS790........................................................................62
5Visualize plants..................................................................................63
5.1 Overview ............................................................................................. 63
5.2 Example of a plant web page ...............................................................64
5.3 Plant web page features ......................................................................65
5.4 Toolbar ................................................................................................66
5.5 Import web-capable plant diagrams......................................................67
5.6 Create own plant web pages................................................................69
6Record consumption data.................................................................73
6.1 Consumption data file ..........................................................................74
6.1.1 Main areas for consumption data file....................................................74
6.1.2 Meter data in detail ..............................................................................75
6.2 Time ratios...........................................................................................76
6.3 Send consumption data file..................................................................79
7"Energy indicator" function ..............................................................80
7.1 Introduction..........................................................................................80
7.1.1 Function description.............................................................................80
7.1.2 KNX bus topology................................................................................81
7.1.3 Synco product range............................................................................82
7.1.4 Navigation and device web pages........................................................83
7.2 "Energy indicator" function levels .........................................................84
7.2.1 "Plant" level .........................................................................................84
7.2.2 "Partial plants" level .............................................................................85
7.2.3 "Data points" level................................................................................86
7.2.4 Number of "Monitored data points".......................................................87
7.2.5 "Energy indicator" visibility ...................................................................88
7.2.6 Summary display "Energy indicator" for a plant....................................89
7.3 "Energy indicator" commissioning function...........................................90
7.3.1 Commissioning notes...........................................................................90
7.3.2 Start "Energy indicator" function...........................................................90
7.3.3 Estimated processing time...................................................................91
7.3.4 Deactivating "Data point monitoring" ....................................................91
7.3.5 Activating "Data point monitoring" ........................................................93
7.4 Dialog boxes, data points, and "Green limits" .......................................95
7.4.1 General dialog boxes...........................................................................95
7.4.2 Dialog boxes with numeric data points .................................................96
7.4.3 Dialog boxes with enumeration data points ..........................................97
7.4.4 Dialog boxes with variable unit data points...........................................98
7.4.5 Dialog boxes for data points with manually set value............................99

5 / 176
Siemens Web server OZW772... V6.0 CE1C5701en
Building Technologies Table of contents 2015-10-12
7.4.6 User groups "Service" and "End user"................................................100
7.5 E-mail with "Energy indicator" for the plant .........................................101
7.5.1 E-mail receiver configuration..............................................................101
7.5.2 Mail inbox ..........................................................................................102
7.5.3 E-mail contents..................................................................................103
7.6 Exceptions.........................................................................................104
8Communications..............................................................................105
8.1 Remote operation ..............................................................................105
8.1.1 Access via portal................................................................................105
8.1.2 Access via Local area network (LAN).................................................106
8.1.3 Access via direct connection.............................................................. 110
8.2 Messages via e-mail .......................................................................... 114
9Trend functions................................................................................ 119
9.1 Overview ........................................................................................... 119
9.2 Define trend.......................................................................................120
9.2.1 Define trend via web ..........................................................................120
9.2.2 Restriction to bus load .......................................................................124
9.2.3 Reset trend definition.........................................................................124
9.2.4 Add trend data points.........................................................................125
9.2.5 Manage trend RAM............................................................................126
9.3 Send trend data by e-mail ..................................................................127
9.3.1 Configure E-mail receiver...................................................................127
9.3.2 Sent transmission options per trend channel ......................................128
9.3.3 E-mail content and appendix..............................................................130
9.4 Download trend file via web ...............................................................131
9.5 Graphical trend display ......................................................................133
9.6 Import/export trend definitions............................................................134
9.7 ACS Trend.........................................................................................137
9.7.1 ACS offline trend compatibility............................................................137
9.7.2 ACS trend bus load............................................................................138
10 KNX S-Mode.....................................................................................139
10.1 Configuration in KNX S-Mode ............................................................141
10.2 Operation KNX S-mode .....................................................................156
11 Appendix..........................................................................................159
11.1 General notes....................................................................................159
11.2 Diagnostics........................................................................................159
11.2.1 Web Server fault codes......................................................................159
11.2.2 Windows Commander........................................................................160
11.3 Communications................................................................................161
11.3.1 Internet protocol.................................................................................161
11.3.2 Free e-mail account providers............................................................161
11.3.3 Install RNDIS driver ...........................................................................162
11.3.4 Alternative network configuration .......................................................164
11.4 Glossary of Ethernet and Internet terms.............................................165
Index ..........................................................................................................172

6 / 176
Siemens Web server OZW772... V6.0 CE1C5701en
Building Technologies Table of contents 2015-10-12

7 / 176
Siemens Web server OZW772... V6.0 CE1C5701en
Building Technologies Overview 2015-10-12
1 Overview
1.1 Introduction
Type designation Max. number of devices on KNX bus
OZW772.01 1 device
OZW772.04 4 devices
OZW772.16 16 devices
OZW772.250 250 devices
The document describes commissioning and operating the Web Server OZW772…
In this edition "Web-Server OZW772…, V6.0" the following extensions were added:
·New default password and minimum password strength. See sections 2.2.2 and
2.5.3.1
·Change to absolute timeout. See Sections 2.5.3.3 and 4.1
·Response to incorrect login. See Section 4.1
·Response to communication problems for trend queries. See Section 9.2.1
·Synchronization of trends. See Sections 9.2.1 and 9.3.2
·New function "Trend graphic". See Section 9.5
·Group Monitoring is supported. See Section 10
·Additional fault codes. See Section 11.2
·Continuous access. See Section 11.3.1
The latest edition is available on www.siemens.com/ozw772-manual.
The ACS790 PC software can also be used to commission and operate the Web
Server OZW772… To simplify reading, this document focuses on commissioning
and operating via web browser.
The symbol to the right identifies special safety notes and warnings.
Ignoring this type of note may result in device damage and personal injury.
·Devices may only be used in building technical plants and for the described
applications only. Comply with all local regulation (installation, etc.).
·Disconnect the power and immediately replace a defective or obviously
damaged device.
·Do not open the device. Failure to comply will invalidate any warranty claims.
·The technical data are provided solely for use with Siemens bus devices. The
user ensures the functionality of operation when using third-party devices not
expressly mentioned here. Siemens assumes no responsibility for service and
warranty under these circumstances.
Type summary
Document contents
Focus on web
browser operation
Important notes
Safety /
Product liability

8 / 176
Siemens Web server OZW772... V6.0 CE1C5701en
Building Technologies Overview 2015-10-12
Trouble-free and safe product operation presupposes transport, storage, mounting,
installation, and commissioning as intended as well as careful operation.
The devices are considered electronics devices for disposal in terms of European
Directive 2012/19/EU and may not be disposed of as domestic waste.
·Dispose of the device via the proper channels.
·Comply with all local and currently applicable laws and regulations.
Intended use
Disposal

9 / 176
Siemens Web server OZW772... V6.0 CE1C5701en
Building Technologies Overview 2015-10-12
1.2 Web Server display and operating elements
Pos Designation
1 LED Operation, portal
connection display and "Energy
indicator"
2 LED
3 LED field bus 2 (reserve)
4 LED fault
5 LED addressing mode
6 Remote button
7Addressing mode button
8 "Message suppression" switch
9 Switch 2 (no function)
10 KNX bus connection terminals
11 Operating voltage connection
12 USB connection Mini-B
13 Ethernet connection, RJ45 plug
·Dark No operating voltage DC 24 V
·Steady red Web Server starts operating system
·Flashing red Web Server starts application
·Steady green Web Server operational, "Energy indicator" = "Green leaf"
·Steady orange Web Server operational, "Energy indicator" = "Orange leaf"
·Flashing Web Server operational, connected to portal
green / orange (LED 0.8 s on, 0.2 s off)
·Dark No bus power
·Lit KNX operational
·Flashing Communication on KNX
·Dark No function
·Dark No fault (normal operating state)
·Lit Acknowledged fault
·Flashing Unacknowledged fault
·Dark KNX addressing mode off
·Lit KNX addressing mode o
·Short (< 2 s) Acknowledges fault message
·Long (> 6 s) Sends system report to fault e-mail Receivers
(not to consumption data and "Energy indicator" Receivers)
·Short (< 2 s) Press once: KNX addressing mode on
Press again: KNX addressing mode off
·Long (> 6 s) Simultaneously pressing the buttons and restores
defaults
All configuration data and settings are reset. The
device list, plant diagrams, and unsent messages are
deleted. History data is not deleted.
·Position ON Sending messages is suppressed
·Position OFF Sending messages permitted
·Switch settings No function
Overview
LED displays
1(red/green/orange)
2(green)
3Field bus 2 (reserve)
4Fault (red)
5Addressing mode (red)
Operating buttons
6Remote button
7Addressing mode
Button combinations
and
Switches
8Message
suppression
9DIP switch 2

10 / 176
Siemens Web server OZW772... V6.0 CE1C5701en
Building Technologies Overview 2015-10-12
1.3 User interface
A web browser is used to access the user interface for the Web Server.
·The Web Server provides text-based operation of the Web Server and
connected Synco devices as a standard (Section 4).
·You can also set up visualized operation (Section 5).
The following describes the display areas for the text-based standard user interface
(display areas for visualization are outlined in Section 5).
The main window is sub-divided into various areas.
The following functions are selected via primary navigation:
Home Menu-based plant and device operation.
Energy indicator Display and operate "Energy indicator" data points.
(displayed only is controller is connected with an Energy indicator)
Faults Display system faults.
File transfer Download consumption data and event history,
upload documents, logos and system definitions.
User accounts User administration.
Device web pages Create device list and operating pages.
Device operation (via home) queries devices and their operating pages via
secondary navigation (menu tree). As of OZW-Version 5.0, KNX pages defined in
ETS are displayed here too.
The path displays the workflow starting at the main menu to the open operating
page. Simply click at any point on the path to return to that location.
This field shows the currently logged-in user. Clicking [Logout] ends the current
session. The session remains active until logout. When connecting via the portal
the symbol is displayed instead of the symbol and the user’s email address
is displayed rather than the user name.
The "Plant state fault" field is displayed permanently:
·Green field: No fault
·Red field: Plant fault
Click the "Plant state fault" field to display all faults in the plant.
The "Plant state Energy indicator" field is displayed permanently:
·Green leaf: All "Energy indicator" data points are always within
their "green limits", i.e. "within the green/allowed range".
·Orange leaf: One or multiple "Energy indicator" data points are
outside their "green limits"
Clicking the "Plant state Energy indicator" field opens the "Energy indicator"
function.

Primary navigation

Secondary navigation

Command sequence

User

Plant state
fault

Plant state
Energy indicator

11 / 176
Siemens Web server OZW772... V6.0 CE1C5701en
Building Technologies Overview 2015-10-12
Displays plant name as entered.
The display range displays content corresponding to the selected function via
primary and secondary navigation.
Shows Logo 1 and Logo 2.
1.3.1 User levels
Displays and operates based access level for the logged on user:
·Operate end user data
·Operating of KNX S-Mode devices
·Fault overview
·Administer own user account
Same as end user. In addition:
·Operate service data
·Documents, message history
Same as service. In addition:
·Create device list and web pages
·The toolbar to create plant web pages
·Administer all user accounts

Plant name

Display

Logo area
End user
Service
Administrator

12 / 176
Siemens Web server OZW772... V6.0 CE1C5701en
Building Technologies Overview 2015-10-12
1.4 Symbols, notations, abbreviations
1.4.1 Symbols
Symbol Meaning
Data point at the service level
Data point at the end user level
Read/write data point; the setting value can be changed
Read-only data point; the value cannot be changed
Link to entry field
Delete object
Checkbox
Selection box
Calendar
Arrows to incrementally adjust values
Adjustment tab
/ Arrow to display sort order
Up
File upload (to Web Server)
File download (from Web Server)
Export file
Import file
Add data point
Move/sort data point
Start trending
Stop trending
Generate trend graph
Calendar for selecting the date
Safety note, intended to protect against misuse
Always observe/follow
Note; important information
Network connection
Link to device
User connected locally or via direct connection (fixed or dynamic IP address).
User connected via portal.
Message history
System definitions
Logos
,Switch over displays: Full view, partial view
/ Fault indication: Green field = no fault; red field = fault (alarm)
"Green leaf"
"Orange leaf"
"Grey leaf"
Symbols

13 / 176
Siemens Web server OZW772... V6.0 CE1C5701en
Building Technologies Overview 2015-10-12
1.4.2 Notations
Paths are printed as follows:
·Web Server: Home > 0.2.150 OZW772.xx > Settings > Time of day/date.
·PC: Start > Settings > Network connections > Local Area Connection.
OZW772.xx stands for: OZW772.01 or
OZW772.04 or
OZW772.16 or
OZW772.250
Enter in the browser address line:
·IP address: 192.168.2.10
·Domain: www.siemens.com
·Portal: https://www.siemens-syncoic.com
Buttons depicted as follows: [ Add ]
1.4.3 Abbreviations
Auto MDI-X Auto Medium Dependent Interface – Crossed.
COV Change of value
ECA Energy Cost Allocation
HTTP Hyper Text Transfer Protocol
HTTPS Hyper Text Transfer Protocol Secure
IP Internet Protocol
KNX Konnex
LAN Local Area Network
NAT Network Address Translation
PAT Port and Address Translation
RNDIS Remote Network Driver Interface Specification
SMTP Simple Mail Transfer Protocol
STP Shielded Twisted Pair
TCP Transmission Control Protocol
TLS Transport Layer Security
UPnP Universal Plug and Play
USB Universal Serial Bus
UTP Unshielded Twisted Pair
Web API Web Application Programming Interface
The glossary, Section 11.4, contains detailed explanations of terms and
abbreviations.
Path indications
IP address, domains
Buttons
Abbreviations

14 / 176
Siemens Web server OZW772... V6.0 CE1C5701en
Building Technologies Commissioning 2015-10-12
2 Commissioning
This section describes how to commission the Web Server.
2.1 Prerequisites
The following conditions must be met to commission the Web Server:
·The Web Server is mounted and wired (see Installation instructions, G5701).
·The connected KNX devices are commissioned.
·The KNX devices have a valid KNX address [1...253] are operating.
Note: Web Servers are delivered with KNX address 150. As a result KNX
address range [1…253], except for 150, applies to all other devices.
·Bus power supply to the KNX bus is available.
·The Web Server or another KNX device is the clock master on KNX.
·The Web Server automatically receives its IP address from the router when the
DHCP client is switched on. The address without router is: 192.168.2.10
(factory setting, see Section 8.1.2)
·Connecting a SmartPhone App to a Web Server makes sense only after the
Web Server is fully commissioned.
The following is required to commission the Web Server on the portal:
·The Web Server is connected to the Internet
The Web Server automatically registers on the portal.
The operation LED starts to flash green / orange as soon as the Web Server is
connected to the portal.
The following is required to commission the Web Server:
·A PC/laptop and a web browser commission Web Server via an USB interface.
The RNDIS driver must be installed to connect via USB. IP address USB:
192.168.250.1 (cannot be changed). The address range 192.168.250.1 -
192.168.250.255 cannot be used for Ethernet and is reserved exclusively for
USB.
·The RNDIS driver is automatically installed when connecting via USB if the
PC/laptop is connected to the Internet (as long as the Microsoft online update
service is enabled). The RNDIS driver can be installed manually if there is no
connection to the Internet (see Section 11.3.3)
·The RNDIS is supplied on the Web Server at http://<IP-Adresse>/drivers/
·To navigate, always start with primary navigation, then use the secondary
navigation to select the desired menu item.
·Return: Click "Upward" or navigate via the path or primary navigation.
General
Notes
Portal commissioning
requirements
Local commissioning
requirements without
portal
Operating notes

15 / 176
Siemens Web server OZW772... V6.0 CE1C5701en
Building Technologies Commissioning 2015-10-12
2.2 Getting started
2.2.1 Turn on Web Server
Connect the Web Server to the power supply and connect it to the PC:
1. Connect power supply to turn on power on Web Server. The Web Server is
operational, when the green LED is lit.
2. Check additional displays:
·LED
Green light if the KNX bus power supply is available. Check KNX bus
wiring and setting for bus power supply on the KNX devices if no bus
power supply is available.
·LED
Dark if no fault pending. You can troubleshoot pending faults later (see
Section 4.3).
3. Plug the supplied USB cable into the Web Server and the PC and start up
the PC. The PC recognizes the Web Server as a USB device.
Otherwise, the RNDIS is still not installed.
4. The RNDIS driver is installed automatically if the PC is connected to the
Internet and no RNDIS driver is installed as long as the Microsoft online
update is enabled. Follow the instructions for the installation program.
You can also manually setup the RNDIS driver (see Section 11.3.3).
Turn on Web Server
Note

16 / 176
Siemens Web server OZW772... V6.0 CE1C5701en
Building Technologies Commissioning 2015-10-12
2.2.2 Log into Web Server
A PC with USB interface and web browser is used to commission the Web Server.
1. Start web browser.
2. In the address line, enter the USB IP address (192.168.250.1).
3. First time Login
·User name Administrator
·Password to V5.2(Password): Password
·Password as of V6.0 (Password): Password.1
4. Click [ Login ] to finish.
5. After logging on the first time, the dialog box is displayed to define a new
password.
·
·A new password must be defined the first time you log in (you can also
change the language).
·You cannot exit the dialog box if you do not define a new password (i.e. not
equal to "Password or Password.1") and the following note is displayed:
·The following message is displayed if you fail to fill out all required fields:
Log on
Important note

17 / 176
Siemens Web server OZW772... V6.0 CE1C5701en
Building Technologies Commissioning 2015-10-12
Observe capitalization when entering the password.
The message "Entry incorrect" is displayed when entering an incorrect password.
The password strength is checked when entering the password and a progress bar
displayed. The bar is orange is the password is week. It changes to green as soon
as the password is strong enough.
The following conditions must be met for a secure password:
·Minimum password length of 8 characters
·At least 1 capital letter
·At least 1 lowercase letter
·At least 1 number
·At least 1 special character
Password and user
name
Minimum password
strength

18 / 176
Siemens Web server OZW772... V6.0 CE1C5701en
Building Technologies Commissioning 2015-10-12
2.3 Administer user accounts
The "User Accounts" ("User accounts") menu changes the administrator password
at delivery and sets up additional user accounts.
The user account settings equally apply to access via Smartphone app and other
applications via Web API.
Procedure:
1. Click red pencil
The "Change user" dialog box opens.
2. Change administrator data:
- Password
- Repeat Password
- Description (optional)
- E-mail address (optional)
- Language: English
3. Close with [ OK ]
Procedure:
1. Click [ Add ]
The "Add user" dialog box opens.
2. Enter / Select user data:
- User name
- Password
- Repeat password
- Description (optional)
- E-mail address (optional)
- Language: English
- User group
3. Close with [ OK ]
Administer user
accounts
Note
Change
administrator data
Add a new user

19 / 176
Siemens Web server OZW772... V6.0 CE1C5701en
Building Technologies Commissioning 2015-10-12
Procedure:
1. Click the red pencil for the corresponding user
The "Change user" dialog box opens.
2. Change user data:
- User name
- Password
- Repeat password
- Description (optional)
- E-mail address (optional)
- Language: English
- User group.
3. Close with [ OK ]
Procedure:
1. Click the red recycle bin for the corresponding user.
The "User accounts" dialog box opens.
2. Click [ Yes ] to confirm "User to be deleted?".
·The administrator account cannot be deleted. The name "Administrator" and
user group "Administrator" cannot be changed. You may, however, add user
accounts with administrator rights.
·You can only add new users and delete existing ones on the "Administrator"
user level.
·Changing other user accounts is reserved to the "Administrator" user level.
·A secure password is comprised of letters, numbers and special characters,
is at least 20 characters in length and does not include a name or words from
dictionaries.
Change user data
Delete user account
Notes

20 / 176
Siemens Web server OZW772... V6.0 CE1C5701en
Building Technologies Commissioning 2015-10-12
2.4 Create device web pages
The associated devices must be recorded and the device websites generated
before operating the Web Server and the Synco devices. Use the "Device web
pages" menu.
Device web pages can only be created on the "Administrator" user level.
Linked devices are listed in a table with the following information:
·Device name
·Device address
·Device type
·Serial number
·State
·Generated on
You can sort the table by clicking
·The Web Server itself is already in the device list.
·Only added devices are monitored.
·Only generated devices can be operated.
·Device web pages can only be generated on the "Administrator" user level.
·Changes to settings of the connected Synco device may require that the device
web pages be recreated or updated to apply changes from web operation.
·You must delete and re-add to replace a Synco device.
Procedure:
1. Click [ Add ]
2. Enter serial number.
The serial number is located on the type label for Synco devices.
3. Confirm with [ OK ]
The Web Server searches for the device with the corresponding serial
number. It appears in the device list if found.
Create device
websites
Note
Notes
Add devices