Siemens SIMATIC NET RUGGEDCOM RSG2100 User manual

Edition 07/2019
Service Manual
SIMATIC NET
Industrial Ethernet Switches
RUGGEDCOM RSG2100
https://www.siemens.com

SIMATIC NET
Industrial Ethernet Switches
RUGGEDCOM RSG2100
Service Manual
Preface
Introduction 1
Module Replacement 2
07/2019
C79000-G8976-1151

Legal Information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety
alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown be-
low are graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger
will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relat-
ing to property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the
specific task in accordance with the relevant documentation, in particular its warning notices and safety in-
structions. Qualified personnel are those who, based on their training and experience, are capable of identify-
ing risks and avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommend-
ed or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permis-
sible ambient conditions must be complied with. The information in the relevant documentation must be ob-
served.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publica-
tion may be trademarks whose use by third parties for their own purposes could violate the rights of the own-
er.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software de-
scribed. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the in-
formation in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Digital Industry
Process Automation
Postfach 48 48
90026 NÜRNBERG
GERMANY
© 07/2019 Subject to Change Copyright © Siemens 2019
All rights reserved

Table of Contents
Preface ............................................................................................................................................ v
Related Documents ................................................................................................................. v
Training ................................................................................................................................... v
Customer Support ................................................................................................................... v
1 Introduction ........................................................................................................................... 1
1.1 Orientation ............................................................................................................ 1
1.2 Required Tools, Materials, and/or Equipment ......................................................... 3
2 Module Replacement ............................................................................................................ 5
2.1 Module Overview .................................................................................................. 5
2.2 Module Removal ................................................................................................... 7
2.2.1 Removing the Cover .............................................................................................. 8
2.2.2 Accessing Modules on the Bottom Row ............................................................... 11
2.2.3 Removing a Module ............................................................................................ 18
2.3 Module Installation ............................................................................................. 25
2.3.1 Changing Faceplate ............................................................................................. 26
2.3.2 Installing a Module ............................................................................................. 27
2.3.3 Installing the Main Inner Assembly ...................................................................... 34
2.3.4 Installing the Cover ............................................................................................. 40
RUGGEDCOM RSG2100
Service Manual, 07/2019, C79000-G8976-1151 iii

Table of Contents
iv RUGGEDCOM RSG2100
Service Manual, 07/2019, C79000-G8976-1151

Preface
This guide describes how to service the RUGGEDCOM RSG2100/RSG2100P.
It is intended for use by network technical support personnel who are responsible for
the installation, commissioning and maintenance of the device.
Related Documents
Other documents that may be of interest include:
Document Title Link
RUGGEDCOM RSG2100 https://support.industry.siemens.com/cs/ww/en/view/82166219
RUGGEDCOM RSG2100F https://support.industry.siemens.com/cs/ww/en/view/109757154
RUGGEDCOM RSG2100P https://support.industry.siemens.com/cs/ww/en/view/8216720
RUGGEDCOM RSG2100PF https://support.industry.siemens.com/cs/ww/en/view/109757155
Training
Siemens offers a wide range of educational services ranging from in-house training
of standard courses on networking, Ethernet switches and routers, to on-site cus-
tomized courses tailored to the customer's needs, experience and application.
Siemens' Educational Services team thrives on providing our customers with the es-
sential practical skills to make sure users have the right knowledge and expertise to
understand the various technologies associated with critical communications net-
work infrastructure technologies.
Siemens' unique mix of IT/Telecommunications expertise combined with domain
knowledge in the utility, transportation and industrial markets, allows Siemens to
provide training specific to the customer's application.
For more information about training services and course availability, visit https://-
www.siemens.com or contact a Siemens Sales representative.
Customer Support
Customer support is available 24 hours, 7 days a week for all Siemens customers.
For technical support or general information, contact Siemens Customer Support
through any of the following methods:
Online
Visit http://www.siemens.com/automation/support-request to submit a
Support Request (SR) or check on the status of an existing SR.
RUGGEDCOM RSG2100
Service Manual, 07/2019, C79000-G8976-1151 v

Preface
Customer Support
Telephone
Call a local hotline center to submit a Support Request (SR). To locate a lo-
cal hotline center, visit http://www.automation.siemens.com/mcms/as-
pa-db/en/automation-technology/Pages/default.aspx .
Mobile App
Install the Industry Online Support app by Siemens AG on any Android, Ap-
ple iOS or Windows mobile device and be able to:
• Access Siemens' extensive library of support documentation, including
FAQs and manuals
• Submit SRs or check on the status of an existing SR
• Contact a local Siemens representative from Sales, Technical Support,
Training, etc.
• Ask questions or share knowledge with fellow Siemens customers and
the support community
vi RUGGEDCOM RSG2100
Service Manual, 07/2019, C79000-G8976-1151

Introduction 1
Welcome to the Service Manual for the RUGGEDCOM RSG2100/RSG2100P.
This document describes the various service tasks that can be performed.
DANGER
Electrocution hazard – risk of serious personal injury and/or damage to equip-
ment.
Before performing any maintenance tasks, make sure all power to the device has
been disconnected and wait approximately two minutes for any remaining energy
to dissipate.
WARNING
Radiation hazard – risk of serious personal injury.
This product contains a laser system and is classified as a CLASS 1 LASER PRODUCT.
Use of controls or adjustments or performance of procedures other than those speci-
fied herein may result in hazardous radiation exposure.
NOTICE
Procedures described in this manual must only be performed by trained, authorized
personnel. Attempted service by unauthorized personnel shall render all warranties
null and void.
Changes or modifications not expressly approved by Siemens AG could invalidate
specifications, test results, and agency approvals, and void the user's authority to
operate the equipment.
1.1 Orientation
The following provides an overview of the device. For more information, refer to the
associated Installation Manual.
LED Display
The LED display provides real-time information about the power supply, individual
ports, and the alarm status. At the time of ordering, the display can chosen to be lo-
cated on the front panel or the top of the device. The position of the display is impor-
tant when removing the top cover.
RUGGEDCOM RSG2100
Service Manual, 07/2019, C79000-G8976-1151 1

Introduction
1.1Orientation
1
3
2
3
1 Top Face
2 Front Face
3 LED Display
Figure1.1 LED Display Options
Modules
The device features 10 module slots, numbered sequentially from left to right, top to
bottom.
1
3
5
7 9
2
4
6
8
10
Figure1.2 Module Number Assignment
Some slots support only a specific type of module. For more information, refer to the
associated Installation Manual.
2RUGGEDCOM RSG2100
Service Manual, 07/2019, C79000-G8976-1151

Introduction
1.2Required Tools, Materials, and/or Equipment
1.2 Required Tools, Materials, and/or Equipment
The following may be required when servicing the device:
Tools
• Drill
• T10 Torx drill bit
• Philips drill bit
• Hex standoff drill bit
Materials
•None
Equipment
• ESD gloves
• ESD shoes
• ESD foam pad
RUGGEDCOM RSG2100
Service Manual, 07/2019, C79000-G8976-1151 3