Siemens SIMATIC NET SCALANCE X-000 Series User manual

SIMATIC NET
Industrial Ethernet switches
SCALANCE X-000
Operating Instructions
12/2018
C79000-G8976-C344-03
Introduction 1
Safety notices 2
Network topologies 3
Description of the device 4
Mounting 5
Connecting up 6
Maintenance and
troubleshooting 7
Technical specifications 8
Dimension drawings 9
Approvals 10

Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified
personnel are those who, based on their training and experience, are capable of identifying risks and avoiding
potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in
this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Division Process Industries and Drives
Postfach 48 48
90026 NÜRNBERG
GERMANY
C79000-G8976-C344-03
Ⓟ 11/2018 Subject to change
Copyright © Siemens AG 2010 - 2018.
All rights reserved

Table of contents
1 Introduction...................................................................................................................................................5
1.1 On the Operating Instructions..................................................................................................5
2Safety notices...............................................................................................................................................9
3Network topologies.....................................................................................................................................11
4 Description of the device............................................................................................................................13
4.1 Product overview....................................................................................................................13
4.2 Product properties and device view.......................................................................................16
4.3 TP ports (twisted pair)............................................................................................................17
4.4 LEDs......................................................................................................................................19
5 Mounting.....................................................................................................................................................21
5.1 Safety notices for installation.................................................................................................21
5.2 Types of installation...............................................................................................................22
5.3 Installation on a DIN rail.........................................................................................................23
5.4 Installation on a standard rail.................................................................................................24
5.5 Wall mounting........................................................................................................................25
6 Connecting up............................................................................................................................................27
6.1 Safety when connecting up....................................................................................................27
6.2 Wiring rules............................................................................................................................28
6.3 Power supply..........................................................................................................................29
6.4 Grounding..............................................................................................................................30
6.5 IE FC RJ-45 Plug 180............................................................................................................30
7 Maintenance and troubleshooting..............................................................................................................33
8 Technical specifications..............................................................................................................................35
9 Dimension drawings...................................................................................................................................41
10 Approvals....................................................................................................................................................43
Index...........................................................................................................................................................51
SCALANCE X-000
Operating Instructions, 12/2018, C79000-G8976-C344-03 3

Table of contents
SCALANCE X-000
4Operating Instructions, 12/2018, C79000-G8976-C344-03

Introduction 1
1.1 On the Operating Instructions
Purpose of the Operating Instructions
These operating instructions support you when commissioning the unmanaged Industrial
Ethernet entry level switches SCALANCE X-000.
Validity of the Operating Instructions
These operating instructions are valid for the following devices:
Device Article number
SCALANCE X005 6GK5 005-0BA00-1AA3
6GK5 005-0BA10-1AA3
SCALANCE X005TS (Transportation
System)
6GK5 005-0BA00-1CA3
SCALANCE X005EEC 6GK5 005-0BA10-1CA3
See also
SIMATIC NET Industrial Ethernet Twisted Pair and Fiber Optic Networks (https://
support.automation.siemens.com/WW/view/en/1172207)
Siemens SCALANCE (https://siemens.com/scalance)
Further documentation
In the system manuals "Industrial Ethernet / PROFINET Industrial Ethernet" and "Industrial
Ethernet / PROFINET passive network components", you will find information on other
SIMATIC NET products that you can operate along with the devices of this product line in an
Industrial Ethernet network.
There, you will find among other things optical performance data of the communications partner
that you require for the installation.
SCALANCE X-000
Operating Instructions, 12/2018, C79000-G8976-C344-03 5

You will find the system manuals here:
● On the data medium that ships with some products:
– Product CD / product DVD
– SIMATIC NET Manual Collection
● On the Internet pages of Siemens Industry Online Support:
– Industrial Ethernet / PROFINET Industrial Ethernet System Manual (https://
support.industry.siemens.com/cs/ww/en/view/27069465)
– Industrial Ethernet / PROFINET Passive Network Components System Manual (https://
support.industry.siemens.com/cs/ww/en/view/84922825)
SIMATIC NET manuals
You will find the SIMATIC NET manuals here:
● On the data medium that ships with some products:
– Product CD / product DVD
– SIMATIC NET Manual Collection
● On the Internet pages of Siemens Industry Online Support (https://
support.industry.siemens.com/cs/ww/en/ps/15247).
SIMATIC NET glossary
Explanations of many of the specialist terms used in this documentation can be found in the
SIMATIC NET glossary.
You will find the SIMATIC NET glossary here:
● SIMATIC NET Manual Collection or product DVD
The DVD ships with certain SIMATIC NET products.
● On the Internet under the following address:
50305045 (https://support.industry.siemens.com/cs/ww/en/view/50305045)
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected
to an enterprise network or the internet if and to the extent such a connection is necessary
and only when appropriate security measures (e.g. firewalls and/or network segmentation) are
in place.
Introduction
1.1 On the Operating Instructions
SCALANCE X-000
6Operating Instructions, 12/2018, C79000-G8976-C344-03

For additional information on industrial security measures that may be implemented, please
visit
https://www.siemens.com/industrialsecurity (https://www.siemens.com/industrialsecurity)
Siemens’ products and solutions undergo continuous development to make them more secure.
Siemens strongly recommends that product updates are applied as soon as they are available
and that the latest product versions are used. Use of product versions that are no longer
supported, and failure to apply the latest updates may increase customers’ exposure to cyber
threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under
https://www.siemens.com/industrialsecurity (https://www.siemens.com/industrialsecurity)
Catalogs
You will find the article numbers for the Siemens products of relevance here in the following
catalogs:
● SIMATIC NET Industrial Communication / Industrial Identification, catalog IK PI
● SIMATIC Products for Totally Integrated Automation and Micro Automation, catalog ST 70
● Industry Mall - catalog and ordering system for automation and drive technology, Online
catalog (https://mall.industry.siemens.com/goos/WelcomePage.aspx?regionUrl=/
de&language=en)
You can request the catalogs and additional information from your Siemens representative.
Device defective
If a fault develops, please send the device to your SIEMENS service center for repair. Repairs
on-site are not possible.
Recycling and disposal
The products are low in pollutants, can be recycled and meet the requirements of the WEEE
directive 2012/19/EU for the disposal of electrical and electronic equipment.
Do not dispose of the products at public disposal sites.
For environmentally friendly recycling and the disposal of your old device contact a certified
disposal company for electronic scrap or your Siemens contact (Product return (https://
support.industry.siemens.com/cs/ww/en/view/109479891)).
Note the different national regulations.
Trademarks
The following and possibly other names not identified by the registered trademark sign ® are
registered trademarks of Siemens AG:
SIMATIC NET, SCALANCE, C-PLUG, OLM
Introduction
1.1 On the Operating Instructions
SCALANCE X-000
Operating Instructions, 12/2018, C79000-G8976-C344-03 7

Introduction
1.1 On the Operating Instructions
SCALANCE X-000
8Operating Instructions, 12/2018, C79000-G8976-C344-03

Safety notices 2
Read the safety notices
Note the following safety notices. These relate to the entire working life of the device.
You should also read the safety notices relating to handling in the individual sections,
particularly in the sections "Installation" and "Connecting up".
CAUTION
To prevent injury, read the manual before use.
Safety notices on use in hazardous areas
General safety notices relating to protection against explosion
WARNING
EXPLOSION HAZARD
Do not open the device when the supply voltage is turned on.
Safety notices when using the device according to Hazardous Locations (HazLoc) and FM.
If you use the device under HazLoc or FM conditions you must also keep to the following safety
notices in addition to the general safety notices for protection against explosion:
This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or non-hazardous
locations only.
This equipment is suitable for use in Class I, Zone 2, Group IIC or non-hazardous locations
only.
SCALANCE X-000
Operating Instructions, 12/2018, C79000-G8976-C344-03 9

Safety notices
SCALANCE X-000
10 Operating Instructions, 12/2018, C79000-G8976-C344-03

Network topologies 3
Switching technology allows extensive networks to be set up with numerous nodes and
simplifies network expansion.
Which topologies can be implemented?
Using the SCALANCE X-000 IE switches, you can implement star topologies.
Note
Keep to the maximum permitted cable lengths of the devices you are using. You will find the
permitted cable lengths in the section "Technical specifications (Page 35)".
Star topology
PC with
CP 1613 A2/
CP 1623
IPC with
CP 1613 A2/
CP 1623
S7-200 with CP 243-1
S7-1200 with
CSM 1277
G_IK10_XX_30039
Panel PC
SCALANCE
X005
Figure 3-1 Example of a star topology with SCALANCE X-000
SCALANCE X-000
Operating Instructions, 12/2018, C79000-G8976-C344-03 11

Network topologies
SCALANCE X-000
12 Operating Instructions, 12/2018, C79000-G8976-C344-03

Description of the device 4
What is possible?
The SCALANCE X-000 IE switches allow the cost-effective installation of small Industrial
Ethernet linear bus or star structures with switching functionality. The devices are designed
for installation in a cabinet.
Note
It is not possible to use a SCALANCE X-000 in a redundant ring because it does not support
redundancy.
Note
If devices are supplied over long 24 V power supply lines or networks, measures are necessary
to prevent interference by strong electromagnetic pulses on the supply lines. These can result,
for example, due to lightning or switching of large inductive loads.
One of the tests used to attest the immunity of these devices to electromagnetic interference
is the "surge immunity test" according to EN 61000-4-5. This test requires overvoltage
protection for the power supply lines. A suitable device is, for example, the Dehn Blitzductor
BVT AVD 24 V type no. 918 422 or a comparable protective element.
Manufacturer:
DEHN+SÖHNE GmbH+Co.KG Hans Dehn Str.1 Postfach 1640 D-92306 Neumarkt, Germany
4.1 Product overview
Table 4-1 Overview of the product characteristics
X005 X005TS X005EEC
SIMATIC environment + + +
Diagnostics LED + + +
24 V DC + + +
2 x 24 VDC - - -
Compact housing
(securing collar, etc.)
+ + +
Signaling contact + on-site operation - - -
Diagnostics: Web, SNMP, PROFINET - - -
C-PLUG - - -
Ring redundancy with RM - - -
Passive ring redundancy - - -
SCALANCE X-000
Operating Instructions, 12/2018, C79000-G8976-C344-03 13

X005 X005TS X005EEC
Standby redundancy - - -
IRT capability - - -
Fast learning - - -
Passive listening - - -
Log table - - -
SNTP + SICLOCK - - -
Cut Through - - -
Coated printed circuit boards - - +
Table 4-2 Overview of the connection options
X005 X005TS X005EEC
TP (RJ-45)
Fast Ethernet 10 / 100 Mbps
5 5 5
Unpacking and checking
WARNING
Do not use any parts that show evidence of damage
If you use damaged parts, there is no guarantee that the device will function according to the
specification.
If you use damaged parts, this can lead to the following problems:
● Injury to persons
● Loss of the approvals
● Violation of the EMC regulations
● Damage to the device and other components
Use only undamaged parts.
1. Make sure that the package is complete.
2. Check all the parts for transport damage.
Components of the product
The following components are supplied with a SCALANCE X-000:
● IE switch SCALANCE X-000
● 2-terminal plug-in block (power supply)
● Product information
Description of the device
4.1 Product overview
SCALANCE X-000
14 Operating Instructions, 12/2018, C79000-G8976-C344-03

Accessories
Component Packaging unit Article number
IE FC Stripping Tool 1 6GK1 901-1GA00
IE FC blade cassettes 1 6GK1 901-1GB00
IE FC TP standard cable GP 1 6XV1 840 2AH10
IE FC TP trailing cable 1 6XV1 840-3AH10
IE FC TP marine cable 1 6XV1 840-4AH10
IE FC TP trailing cable GP 1 6XV1 870-2D
IE FC TP flexible cable GP 1 6XV1 870-2B
IE FC RJ-45 Plug 180 1 6GK1 901-1BB10-2AA0
IE FC RJ-45 Plug 180 10 6GK1 901-1BB10-2AB0
IE FC RJ-45 Plug 180 50 6GK1 901-1BB10-2AE0
Description of the device
4.1 Product overview
SCALANCE X-000
Operating Instructions, 12/2018, C79000-G8976-C344-03 15

4.2 Product properties and device view
Possible attachments
The SCALANCE X-000 has five RJ-45 jacks for connection of end devices or other network
segments.
Figure 4-1 SCALANCE X005
Note
The SCALANCE X005 shown above has the same construction as the SCALANCE X005TS
and SCALANCE X005EEC.
Description of the device
4.2 Product properties and device view
SCALANCE X-000
16 Operating Instructions, 12/2018, C79000-G8976-C344-03

4.3 TP ports (twisted pair)
RJ-45 connector pinout
With SCALANCE X-000, the twisted-pair ports are designed as RJ-45 jacks with MDI-X pin
assignment (Medium Dependent Interface Autocrossover) of a network component.
Pin number Assignment
Pin 8 n. c.
Pin 7 n. c.
Pin 6 TD-
Pin 5 n. c.
Pin 4 n. c.
Pin 3 TD+
Pin 2 RD-
Pin 1 RD+
Note
Permitted cable lengths
TP cords or TP-XP cords with a maximum length of 10 m can be connected to the TP port with
RJ-45 jacks.
With the IE FC cables and IE FC RJ-45 plugs 180, an overall cable length of a maximum of
100 m is permitted between two devices depending on the cable type.
Autonegotiation
With the autonegotiation mechanism, repeaters and end devices can automatically determine
the transmission speed and the transmission mode of the partner port. This makes it possible
to configure different devices automatically.
Description of the device
4.3 TP ports (twisted pair)
SCALANCE X-000
Operating Instructions, 12/2018, C79000-G8976-C344-03 17

Two components connected to a link segment can exchange information about the data
transfer and can adapt their settings to each other. The mode with the highest possible speed
is set.
Note
Setting ports with a fixed configuration
Devices not supporting autonegotiation must be set permanently to 100 Mbps half duplex or
10 Mbps half duplex.
Auto polarity exchange
If the pair of receiving cables is connected incorrectly (RD+ and RD- interchanged), the polarity
is adapted automatically.
Note
The SCALANCE X-000 IE switches are plug-and-play devices that require no settings during
commissioning.
MDI / MDI-X autocrossover function
With the MPI/MDI-X autocrossover function, the send and receive contacts of an Ethernet port
are assigned automatically. The assignment depends on the cable with which the
communications partner is connected. This means that it does not matter whether the port is
connected using a patch cable or crossover cable. This prevents malfunctions resulting from
mismatching send and receive lines. This makes installation much easier for the user.
The SCALANCE X-000 devices support the MDI / MDI-X autocrossover function.
Insulation between the TP ports
NOTICE
Formation of loops
Note that the direct connection of two ports or accidental connection over several switches
causes an illegal loop that can cause network overload and failure.
Devices with port groups
On the following devices, the ports are divided into port groups.
● SCALANCE X005
6GK5 005-0BA00-1AA3
● SCALANCE X005TS
6GK5 005-0BA00-1CA3
Description of the device
4.3 TP ports (twisted pair)
SCALANCE X-000
18 Operating Instructions, 12/2018, C79000-G8976-C344-03

There are two TP port groups:
Group 1: P1
Group2: P2 to P5
Between ports of different port groups, an insulation voltage of 1.5 kV is adhered to
(corresponds to IEEE802.3, Chapter 33.4.1.1, Environment B), e.g. between P1 and P2.
The requirements for Environment A are met between ports of the same group, e.g. between
P2 and P5.
Devices without port groups
The following devices do not have port groups:
● SCALANCE X005
6GK5 005-0BA10-1AA3
● SCALANCE X005EEC
6GK5 005-0BA10-1CA3
The requirements for Environment A are met between all ports.
4.4 LEDs
Power LED "L" (green LED)
The power LED shows the status of the power supply.
LED color LED status Meaning
Green Lit Power supply is connected.
- Off Power supply is not connected or <14 V.
Port LEDs "P" (green/yellow LEDs)
The port LEDs indicate the status of the ports.
LED color LED status Meaning
Green Lit TP link exists, no data reception at port
Yellow Lit TP link exists, data reception at port
Yellow Flashing Test phase during power on
Description of the device
4.4 LEDs
SCALANCE X-000
Operating Instructions, 12/2018, C79000-G8976-C344-03 19

Description of the device
4.4 LEDs
SCALANCE X-000
20 Operating Instructions, 12/2018, C79000-G8976-C344-03