Siemens EUROSET 805S User manual

ΤΗΛΕΦΩΝΙΚΗ ΣΥΣΚΕΥΗ SIEMENS 805 S
•Overview of Euroset 805 S
•Installation
•Setting dialing method
•Setting the volume of tone ringing
•Last number Redial
•Saved number redial
•Speed dialing
•Repertory keys
•Mute
•Recall key
•Configuration of telephone socket

Overview of Euroset 805 S

Installation

Spiral handset cord
Insert connector (at long straight end) into socket marked until it is heard
to engage. Attach short end to handset.
Connecting cord
Insert the one connector into socket on lower side, and insert the other
connector into wall socket. Secure connecting cord in cable guide provided.
The signaling method of your telephone must be set to MF tone dialing or loop
disconnect (LD) dialing (depending on the dialing method of the
telecommunication station) before you put your telephone into operation. When
delivered, your telephone is set for MF tone dialing.
Check: Dial any digit. If you hear the dial tone, you must change over to the
other dialing method.
Setting dialing method
The signaling method of your telephone must be set to MF tone dialing or loop
disconnect (LD) dialing (depending on the dialing method of the
telecommunication station) before you put your telephone into operation. When
delivered, your telephone is set for MF tone dialing.
Check: Dial any digit. If you hear the dial tone, you must change over to the
other dialing method.
Set
Pushbutton on base of telephone
T for MF / time break recall (TBR)
P for LD / earth loop recall (ELR)

Temporary changeover with
-only if tone/pulse switch is set to "P" -
Once a connection has been set up, you can switch to MF tone dialing by pressing
(e.g. to operate an answering machine).
The telephone automatically reverts to dial pulsing once the connection has been
cleared down.
Setting the volume of tone ringing
Pushbutton on base of telephone:
There are three optional levels:
1 = min. vol.
2 = normal vol.
3 = max. vol.
Last number redial
You can redial the last number dialed by lifting the handset and pressing the
REDIAL key .
The memory is cleared if the number entered contains
more than 32 digits.

Saved number redial
Storing
The number dialed can be stored while a call is in progress by pressing the
MEMO key M. This number is remains stored even if other calls are
subsequently made.
Dialing
Lift the handset and press M.
A number remains stored until a new number is stored with
the MEMO key M.
Speed dialing
You can store up to 10 frequently required numbers as speed dialing destinations
(max. 16 digits each) can be stored on digit keys.
Storing numbers
Lift the handset and press the SET key . Enter the number and press the
SET key again. Enter the required speed dialing number (between 0 and
9). Replace the handset.
If you are in the middle of a call, you can store the number just dialed by pressing
the SET key twice and entering the speed dialing number on which the
number is to be stored.
Dialing speed dialing numbers

Lift the handset and press the speed dialing key/MEM . Enter the speed
dialing destination between 0 and 9.
•A dialed number is not stored if it contains more than
15 digits.
•You can delete the number assigned to a specific
key by overwriting it.
•Dial pauses (approx. 3.6 seconds - not in first
position) can be inserted by pressing the key.
These pauses are included in the speed
dialing/name keys and redial memory and are
required in the case of certain PABXs (e.g. 0
2368).
•The keys and are stored regardless of
the dial type, but can only be selected in the case of
DTMP signaling.
Repertory keys
Three repertory keys are available for up to 32 digits each.
Storing
Lift the handset and press the SET key . Dial the number and press the
SET key again. Press one of the 3 repertory keys . The number is now
stored on this repertory key. Replace the handset.

Storing during a call
Press the SET key twice followed by the repertory key on which the
number is to be stored.
Repertory dialing
Lift the handset and press the repertory key . The number stored on this key
is immediately dialed. Please see note under " Speed dialing ".
Mute
You can deactivate the handset completely by pressing the MUTE key
while a call is in progress. The other party can no longer hear you. To activate
the handset, simply press the key once more.
RECALL key
Use the RECALL key to use additional PABX features, if applicable.
Configuration of telephone socket
Configuration of the socket for the connecting cord on the lower side of the
telephone set: