Siemens HiPath optiPoint 100 advance Installation manual

HiPath
optiPoint 100 advance
Installation and Startup

*1PA31003-H4100-A102-1-74D1*
1P A31003-H4100-A102-1-74D1
Siemens AG 2001 ● Information and Communication Networks, Hofmannstraße 51, D-81359 München
Reference No.: A31003-H4100-A102-1-74D1
Made in Germany.
Subject to availability. Right of modification reserved.
HiPath is a trademark of Siemens AG that is registered in Germany and other jurisdictions.
The device conforms to the EU guideline 1999/5/EG, as attested bythe CE
mark.
This device has been manufactured in accordance with our certified envi-
ronmental management system (ISO 14001). This process ensures that
energy consumption and the use of primary raw materials are kept to a min-
imum, thus reducing waste production.

3
This guide for Installation and Startup describes how to connect
the components of the optiPoint 100 advance telephone and how
to integrate the telephone into a LAN environment.
Administrators who wish to install and configure IP phone telepho-
ny devices via a web interface will find detailed informations in the
"Administrator Manual".
Preparing the telephone
To connect the telephone components, proceed as follows:
●Latch the Western plug of the handset cord in the handset
receptacle ("short end").
●Latch the other end of the cord in the receptacle (3) on the
bottom of the telephone ("long end").
●
LatchtheLAN cordwiththeeight-pinWesternplug(RJ45) inthe
receptacle (2) on the bottom of the telephone, and connect with
LAN. Feed the cord through the guide channel in the base unit.
Danger!
You must connect the optiPoint 100 advance first to the
LAN and after that to the power supply.
The two cable ends of the handset cord are equipped
with identical four-pin Western plugs (RJ 11).

4
●Latch the four-pin (red) Western plug (RJ 11) ofthe power sup-
ply unit cord in the receptacle (1) on the bottom of the tele-
phone. Feed the power supply unit cord through the guide
channel in the base unit.
Integrating the telephone into the communication environment
Adaption to an existing network
1. Ask your network administator to assign an Ethernet port
(10BaseT) to your telephone.
2. Ask him if the network contains a DHCP server and a SNTP
server.
If no DHCP server exists he has to give you an IP addressfor
the telephone and for the subnet mask which you haveto enter
into your telephone manually.
If no SNTP server exists, you have to enter time and date man-
ually into your telephone.
Likeall terminal equipment connected to a LAN, the optiPoint 100
advance must have an IP address assigned. The procedure for
setting up the network environment for the telephone is described
below. Note that the optiPoint 100 advance is designed to operate
in a HiPath environment, but this is not mandatory.
If the optiPoint 100 advance is used in a HiPath environment and
a DHCP server is integrated in the HiPath environment, the tele-
phone unit will automatically get an IP address from it when you
connect it to the LAN for the first time. Otherwise, you must manu-
ally enter an IP address for the unit. You have to enter manually
the unit’s telephone number in any case.
The Western plugs of all cable connections must audibly
snap into place.
Without HiPath environment the telephone is only reach-
able via a telephone number (E.164/H.323) if a gatekee-
per is integrated in the network.
Otherwise it is only reachable via IP address.

5
Assign telephone number in a HiPath system with DHCP server
After the automatic assignment of an IP address the following dis-
play is shown:
If the HiPath password is not yet configured you will be prompted
(default: no password is set):
Following the entry of your own telephone number, the telephone
changes over to its normal operating mode (Basic menu). You can
now receive and make calls.
13:05PM bbbbbbbbbbb 07.02.01
Only IP-dialing possiblebb > >Change to "Service" and
?call menu
Service:
1=Status? > Enter digit "6"
Enter Admin password
****** Continue with OK > Enter Admin password
(Default: "123456")
and
Confirm
?
Administration:
1=Network? > >Change to "System"
and
?call menu
System:
1=Type? > >Change to "E164 ad-
dress" and
?Confirm
Enter E164
_>
Enter the telephone
number assigned to this
telephone set and
Enter E164
1289 > ?Confirm
Enter HiPath password
****** Enter HiPath password
and
?Confirm
optiPoint 100 advance
Vxx.yy >
13:15PM
1289 07.02.01 >Basic menu

6
Setting up the optiPoint 100 advance in a HiPath system without DHCP server
If there is no DHCP server integrated into your HiPath environ-
ment, you have to enter the IP address and the subnet mask ma-
nually via your dialling keypad. First you have to switch off the
DHCP function.
No IP address 07.02.01
>>Change to "Service"
and
?call menu
Service:
1=Status? > Enter digit "6"
Enter Admin password
_>
Enter Admin password
(Default: "123456")
and
Enter Admin password
****** Continue with OK > ?Confirm
Administration:
00=End? > >Change to "network"
and
?call menu
Network:
00=End? > >Change to
"DHCP IP assign"
and
Network:
01=DHCP IP assign? On >?Confirm
DHCP IP assign:
Change? On >?Confirm the change
Network:
01=DHCP IP assign? Off >Function is switched off
hBack to Basic menu

7
Stay in the "network" menu and enter an IP address for the tele-
phone and for the subnet mask:
Press the asterisk key (*) on your key pad to enter the separation
points for the IP address.
Repeat these steps for the menu choice "03=Terminal mask"
to enter the corresponding mask IP address.
Network:
01=DHCP IP assign? Off >>Change to
"Terminal IP-Adr."
and
Network: d ddddddddd 0.0.0.0
02=Terminal-IP-Adr? dddddd > ?Confirm
Terminal-IP-Adr dddd 0.0.0.0
Change? dddddddddddddddddd > ?Confirm
Terminal-IP-Adr
000.000.000.000 Enter new IP address
and
Terminal-IP-Adr
19.3.35.112 ?Confirm
Network: d ddddd 19.3.35.112
02=Terminal-IP-Adr? dddddd > Entered IP address is
shown
hBack to Basic menu
After changing IP addresses, you will be prompted to re-
start the phone. The change will otherwise not become
effective.

8
Assigning a telephone number (E.164)
After restarting your telephone you have to assign a telephone
number to your optiPoint 100 advance. The following display is
shown:
Following the entry of your own telephone number, the telephone
changes over to its normal operating mode (Basic menu). You can
now receive and make calls.
13:05PM bbbbbbbbbbb 07.02.01
Only IP-dialing possiblebb > >Change to "Service"
and
?Call menu
Service:
1=Status? > Enter digit "6"
Enter Admin password
****** Continue with OK > Enter Admin password
(Default: "123456")
and
Confirm
?
Administration:
1=Network? > >Change to "System"
and
?Call menu
System:
1=Type? > >Change to
"E164 address" and
?Confirm
Enter E164
_>
Enter telephone number
and
Enter E164
1289 > ?Confirm
hBack to Basic menu
13:15PM
1289 07.02.01 >Basic menu

9
Operating without HiPath environment
If you want to use your optiPoint 100 advance in a network without
HiPath environment you have to switch off the "HiPath" function:
13:15PM bbbbbbbbbbb 07.02.01
1289 bbdddddddddddddddbbbb > >Change to "Service"
and
?Call menu
Service:
1=Status? > Enter digit "6"
Enter Admin password
****** Continue with OK > Enter Admin password
(Default: "123456")
and
confirm
?
Administration:
1=Network? > >Change to "System"
and
?Call menu
System:
1=Type? > ?Call "Type" menu
Type:
HiPath? On >>Confirm
HiPath:
Change? On >>Confirm
Type:
HiPath? Off >Function ist switched off
hBack to Basic menu

10
Setting date and time
If no SNTP server is accessible in your network environment, you
have to set manually the time and date of your telephone:
13:15PM
1289b07.02.01 >>Change to "Service"
?Call menu
Service:
1=Status? > >Changeto"Configuration"
and
?Call Menu
Configuration:
01=Country options? > >Change to "Date/Time"
and
?Confirm
Configuration:
03=Date/Time? DD.MM.YY >?Confirm
?Call menu
Date format:
1=DD.MM.YY? DD.MM.YY >>Change to desiredformat
and
?Confirm
Date: ddddddddddddd DD.MM.YY
Day=00 Month=00 Year=00 Enter the date and
?Confirm
Date: ddddddddddddd DD.MM.YY
Hour=00 Minute=00 Enter the time and
?Confirm
hBack to Basic menu