SignaMax I-100 Series User manual

Quick Start Guide
I-100 Series Switches

www.signamax.com
I-100 SERIES
QUICK START GUIDE
Warnings and Cautionary Messages
Warning: This product does not contain any serviceable user parts.
Warning: Installation and removal of the unit must be carried out by qualied personnel only.
Warning: When connecting this device to a power outlet, connect the eld ground lead on the
tri-pole power plug to a valid earth ground line to prevent electrical hazards.
Warning: This switch uses lasers to transmit signals over ber optic cable. The lasers are
compliant with the requirements of a Class 1 Laser Product and are inherently eye safe in
normal operation. However, you should never look directly at a transmit port when it is powered
on.
Warning: When selecting a ber SFP device, considering safety, please make sure that it
can function at a temperature that is not less than the recommended maximum operational
temperature of the product. You must also use an approved Laser Class 1 SFP transceiver.
Caution: Wear an anti-static wrist strap or take other suitable measures to prevent electrostatic
discharge when handling this equipment.
Caution: Do not plug a phone jack connector in the RJ-45 port. This may damage this device.
Caution: Use only twisted-pair cables with RJ-45 connectors that conform to FCC standards.
1
!
!

www.signamax.com
DIN-Rail Mounting Kit - one bracket
and two screws.
Documentation—Quick Start Guide
(this document) and Warranty Card
Mount the Switch
2
Part
Number
RJ-45
Ports
PoE
Ports
SFP
Ports
SI10011 8 Gigabit 8 2
SI10021 8 Gigabit N/A 2
SI10031 4 Gigabit 4 2
SI10041 4 Gigabit N/A 2
SI10050 6 10/100 4 N/A
Note: Additional documentation can be
obtained from www.signamax.com
1. Screw the DIN-Rail bracket to the switch.

www.signamax.com3
3. Pull down the DIN-Rail bracket to the DIN-Rail track
and check if it is mounted tightly on the DIN-Rail
track.
2. Insert the top of the DIN-Rail bracket to the DIN-Rail
track.

www.signamax.com
I-100 SERIES
QUICK START GUIDE
4
Ground the Switch
1. This equipment must be grounded. Never defeat
the ground conductor or operate the equipment
in the absence of a suitably installed ground
conductor. Contact the appropriate electrical
inspection authority or an electrician if you are
uncertain that suitable grounding is available.
2. Attach a lug (not provided) to a #12 AWG (PoE
switch) or #18 AWG (non-PoE switch) minimum
grounding wire (not provided), and connect it to
the grounding point on the switch rear panel. Then
connect the other end of the wire to ground.
Caution: The earth connection must not be
removed unless all supply connections have
been disconnected.
Note: The device must be installed in a
restricted access location. It should have a
separate protective earthing terminal on the
chassis that must be permanently connected
to earth to adequately ground the chassis and
protect the operator from electrical hazards.
!
Connect Power
1. Insert the positive and negative wires into the PWR1
(+,-) and PWR2 (+,-) on the terminal block connector.
2. Tighten the screws to prevent the wires from
loosening.
PWR 2 PWR 1

www.signamax.com
I-100 SERIES
QUICK START GUIDE
5
Connect Network Cables
1. For RJ-45ports, connect 100-ohm Category 5, 5e or
better twisted-pair cable
2. For the SFP slots, rst install SFP transceivers and
then connect ber optic cabling to the transceiver
ports. The following transceivers are supported:
1000BASE-SX (065-79SXMG)
1000BASE-LX (065-79LXMG)
1000BASE-ZX (065-79ZXMG)
1000BASE-LHX (065-79LXEDMG)
3. As connections are made, check the port status
LEDs to be sure the links are valid. See the LED
description table on the next page.
Verify Switch Operation
1. Verify basic switch operation by checking the system
LEDs. When operating normally, the Power LED
should be on and green.

www.signamax.com
I-100 SERIES
QUICK START GUIDE
6
LED Status Description
PWR ON Switch operating normally.
OFF No DC power is connected or the switch has failed.
LINK
ON Port has a valid link
BLINKING Port has network activity
OFF The link is down
PoE
ON A PoE device is connected and delivered PoE power
BLINKING PoE Error: short circuit or current overload
OFF Doesn’t deliver PoE power
MODE ON Port has a valid 1000 Mbps link
OFF Port has a valid 10/100 Mbps link

999 NW 159th Dr, Miami, FL 33169
800.446.2377 / 305.944.7710
CONNECT WITH US
www.signamax.com