SIIG Parallel Pro User manual

Installation
2-1
DMA
J1
0135791011 12
S
P
P
B
P
P
E
C
P
E
P
P
E
P
P
E
C
P
LPT
MODE
J4
PRT
IRQ
3
7
8
2
7
8
PORT
ADDRESS
J2
J3
Chapter 2
Installation
This chapter will guide you through the installation of your
Parallel Pro . It includes instructions on:
• properly configure the jumpers on your board
• install your Parallel Pro in your computer
2-1 Board Layout
Parallel
(Printer)
Port
Figure 2-1. Parallel Pro Board Layout

2-2
Parallel Pro User's Manual
2-2 Configuring the Parallel Pro
Prior to installing the Parallel Pro , verify the configuration
about your computer. The factory default jumper settings
shouldworkwithmostsystems. However,youshouldmake
sure that the default settings on the board are different from
any other existing devices' in your system. A conflict
results when two addresses are the same. Please refer
to the following sections for alternate jumper settings and
Chapter 3: Verifying and Configuring System Resources for
more information regarding system resources.
2-2.1 Setting Jumpers
The following illustrates the installed positions on a 2-pin
jumper. Italsoshowsthenon-jumperedpositionandposition
for convenient storing.
To change a jumper, simply remove a selected jumper by
pullinguponitspulltab.Toinstallajumper,centeritoverthe
two appropriate pins and push down gently until it is seated.
Figure 2-2. Jumper Positions
No Jumper Installed Jumper Installed
Storage
Position

Installation
2-3
3
7
8
2
7
8
PORT
ADDRESS
J2
3
7
8
2
7
8
2-2.3 Configuring the Parallel (Printer) Port
The parallel port is factory set as I/O port address 278h,
IRQ9 , ECP/EPP mode and DMA 3. These configurations
can be changed by resetting J2, J3, J4 and J1 respectively.
I/O Port Address
Description Jumper Jumper Setting
378h J2
278h* J2
DMA
J1
0135791011 12
S
P
P
B
P
P
E
C
P
E
P
P
E
P
P
E
C
P
LPT
MODE
J4
J3
3
7
8
2
7
8
PORT
ADDRESS
J2
PRT
IRQ
Description Jumper-Pins Default Setting
Parallel Port J2 278 278h
J3 9 IRQ 9
J4 ECP/EPP ECP/EPP
J1 3 DMA 3
Figure 2-3. Default Jumper Settings
2-2.2 Default Jumper Settings
* = Factory Default

2-4
Parallel Pro User's Manual
PRT
IRQ
57912
10 11
J3
5
5
5
5
5
7912
10 11
7912
10 11
7912
10 11
7912
10 11
7912
10 11
Interrupt Request
Description Jumper Jumper Setting
IRQ5 J3
IRQ7 J3
IRQ9* J3
IRQ10 J3
IRQ11 J3
IRQ12 J3
Note: A typical sound card will use IRQ5. If you want to
useIRQ5 asyour parallelport setting,please referto your
sound card’s manual and reconfigure your sound card’s
IRQ settings to avoid conflicts.
* = Factory Default

Installation
2-5
Port Mode
Description Jumper Jumper Setting
SPP/BPP J4
ECP/EPP* J4
EPP J4
ECP J4
Note: If EPP mode is selected, the I/O address 3BCh
cannot be used.
DMA Channel
Description Jumper Jumper Setting
DMA 0 J1
DMA 1 J1
DMA 3* J1
No DMA J1
Selected
* = Factory Default
E
C
P
E
/P
P
E
P
P
E
C
P
E
/P
P
E
P
P
E
C
P
E
/P
P
E
P
P
E
C
P
E
/P
P
E
P
P
S
P
P
B
/P
P
E
C
P
S
P
P
B
/P
P
S
P
P
B
/P
P
S
P
P
B
/P
P
E
C
P
E
C
P
E
C
P
LPT
MODE
J4
0 1 3
0 1 3
0 1 3
0 1 3
DMA
J1