SIIG CyberSerial POS 4000RJ User manual

1
CyberSerial POS 4000RJ
Quick Installation Guide
04-0230A
Introducing the CyberSerial POS 4000RJ
TheCyberSerial POS 4000RJ isahigh-speedplug-n-playPCIbusserial
I/O card that provides 5V or 12V DC output.
Features and Benefits
•Provides four RJ45 high-speed serial ports which can be
individually configured as standard RS232 serial ports or RS232
serial ports with 5V/12V DC output
• Supports both 8-pin and 10-pin RJ45 cable for device connections
•Conforms to PCI v2.2 Plug and Play
•Full support for DOS and Windows based software
•Improves I/O access speed up to 8 times faster than existing
ISA-bus serial ports. Reduces CPU load and improves system
performance dramatically
•IRQ sharing feature eliminates IRQ conflicts
•Works with 56K V.90 external modems, ISDN terminal adapters,
PDAs, digital cameras, label printers and other serial port devices
•Built-in 16-byte (32-byte for 16650 model, 128-byte for 16850
model) FIFO buffers dramatically increase data transmit/receive
speed, especially under Windows multitasking environment
System Requirements
•Pentium or equivalent computer with an available 32-bit PCI slot
•DOS/Windows 3.1x, Windows 95/98/98 SE/ME/NT 4.0/2000/
XP
Package Contents
• One CyberSerial POS 4000RJ board
• One driver installation diskette
• One 5-year warranty card
• This quick installation guide

2
Hardware Installation
General instructions for installing the card are provided below,
since the design of computer cases and motherboards vary. Refer
to your computer’s reference manual for further information, if
needed.
Caution: Static Electricity Discharge may permanently damage
your system. To avoid possible static electricity discharge during
the installation, please follow the guidelines below:
•Dischargeanystaticelectricitybuildupinyourbodyby
touchingalargegroundedmetalsurfaceorthecomputer’scase
(ifpluggedin), forafewseconds.
•During the installation, avoid any contact with internal parts.
Handle cards only by their external edges.
1. Turn OFF the power to your computer and any other
connected peripheral devices.
2. Unplug the power cord from the back of the computer.
3. Remove your computer’s cover.
4. Remove the slot bracket from an available PCI slot.
5. To install the card, carefully align the card's bus connector
with the selected PCI slot on the motherboard. Push the board
down firmly, but gently, until it is well seated.
6. Replace the slot bracket's holding screw to secure the card.
7. Replace the computer cover and reconnect the power cord.
Pin Definition, Jumper Settings and Layout
RJ45 10-Pin Pin Definition
Pin#12345678910
Signal RI or 5/12V
DC DSR RTS CD or
5/12V
DC TX RX Signal
GND CTS DTR Case
GND

3
RJ45 8-Pin Pin Definition
Standard RS-232 DB9 Pin Definition
RI Pin Jumper Settings
Key: O=Open, S=Short, -=N/A
Pin#12345678
Si
g
nal DSR RTS CD or 5/12V
DC TX RX Si
g
nal
GND CTS DTR
Pin#123456789
Si
g
nal CD RX TX DTR GND DSR RTS CTS RI
Port Mode JP1 JP2 JP3 JP4 JP9
Port1RIO----
Port 2 RI - O - - -
Port 3 RI - - O - -
Port4RI---O-
Port 1 5V S - - - 1-2 S
Port 2 5V - S - - 1-2 S
Port 3 5V - - S - 1-2 S
Port45V---S1-2S
Port 1 12V S - - - 2-3 S
Port 2 12V - S - - 2-3 S
Port 3 12V - - S - 2-3 S
Port412V---S2-3S

4
CD Pin Jumper Settings
Key: O=Open, S=Short, -=N/A
Port Mode JP5 JP6 JP7 JP8 JP10
Port1CDO----
Port2CD-O---
Port 3 CD - - O - -
Port4CD---O-
Port 1 5V S - - - 1-2 S
Port 2 5V - S - - 1-2 S
Port 3 5V - - S - 1-2 S
Port 4 5V - - - S 1-2 S
Port 1 12V S - - - 2-3 S
Port 2 12V - S - - 2-3 S
Port 3 12V - - S - 2-3 S
Port 4 12V - - - S 2-3 S

5
Board Layout
JP8
JP4
JP3
JP6
JP2
JP5
JP1
JP7
JP9
JP10
CyberSerial Pos 4000RJ board layout
Jumper Description
•JP1: Select RI/voltage output for Port 1
• JP2: Select RI/voltage output for Port 2
• JP3: Select RI/voltage output for Port 3
•JP4: Select RI/voltage output for Port 4
•JP5: Select CD/voltage output for Port 1
•JP6: Select CD/voltage output for Port 2
•JP7: Select CD/voltage output for Port 3
•JP8: Select CD/voltage output for Port 4
•JP9: Select RI Pin voltage output for port 1, 2, 3 and 4
• JP10: Select CD Pin voltage output for port 1, 2, 3 and 4
1
Port 4
Port 3
Port 1
Port 2

6
Software Installation
This section provides information on how to install the
CyberSerial POS 4000 drivers for the following operating systems:
Windows 95b/98/98 SE/ME
Windows NT 4.0
Windows 2000
Windows XP
DOS/Windows 3.1x
Windows 95b Driver Installation
1. At the Update Device Driver Wizard window, click Next.
2. Insert the Driver Installation diskette in the floppy drive, and
click Other Locations. Type in a:\Win95, click OK, then
Finish.
3. From the Insert Disk window, click OK. When the Copying
Files dialog box appears, type in a:\Win95, then click OK.
4. Remove the diskette and select Yes to restart the computer for
the setup to take effect.
Windows 98/98 SE Driver Installation
1. At the Add New Hardware Wizard window, click Next.
2. Select Search for the best driver for your device
(Recommend), then click Next.
3. Select Specify a location, insert the Driver Installation diskette
and type in a:\Win98, then click Next.
4. Click Next, then Finish.
5. Remove the diskette and click Yes to restart your system.
Windows ME Driver Installation
1. At the Add New Hardware Wizard screen, choose Specify the
location of the driver (Advanced), then click Next.
2. Check Specify a location, insert the Driver Installation diskette
into your floppy drive, type in A:\Win98, then click Next.
3. Click Next, and Finish to complete driver installation.
4. Remove the driver diskette and click Yes to restart Windows.

7
To verify successful installation in Windows 95/98/98 SE/ME:
1. From the main desktop, double click My Computer, Control
Panel,System,then click Device Manager.
2. Double click Ports (COM & LPT) and new Cyber PCI ports
should be displayed. Also, double click SIIG Cyber PCI
option and SIIG ... PCI Board should be displayed.
The board is ready to connect new devices.
Windows NT 4.0 Driver Installation
1. From the desktop click Start, then Run.
2. Insert the Driver Installation diskette, type in A:\NT4\setup,
then click OK.
3. Click Next when the Welcome window appears.
4. From Choose Destination Location window, click Next.
5. Remove the Driver Installation diskette, select Yes to restart
Windows and click Finish.
To verify successful installation in Windows NT 4.0:
1. Go to Start / Setting / Control Panel,double click SIIG Cyber
PCI 20X device icon.
2. New COM port address and LPT number will be assigned for
the ports when successfully installed. The board is ready to
connect devices.
To change the I/O address in Windows NT 4.0:
1. Double click Start, Settings, Control Panel,then SIIG Cyber
PCI 20X device icon.
2. Highlight the LPT or COM address and click Settings.
3. Select or type in an I/O address supported by the device you
would like to configure and click OK. Make sure the selected
I/O address does not conflict with other device in your system.
4. Select Restart Now for the new setup to take effect.

8
Windows 2000 Driver Installation
1. At the New Hardware Wizard, click Next.
2. Select Search for a suitable driver for my device
(recommended) and click Next.
3. Select Specify a location, uncheck the other options and click
Next.
4. Insert the Driver Installation diskette, type in A:\Win2K and
click OK.
5. Click Next and Finish to complete driver installation.
Windows XP Driver Installation
1. At the Found New Hardware Wizard select Install from a list
or specific location (Advanced), then click Next.
2. Insert the Driver Installation diskette, check Include this
location in the search, type in A:\Win2K and click Next.
3. Click Continue Anyway and Finish.
4. Repeat steps 1-3 four more times.
5. Restart the computer to complete the installation.
To verify successful installation in Windows 2000/XP:
1. Double click My Computer, Control Panel, System, Hardware,
and click Device Manager.
2. Click on the + (plus sign) in front of Ports (Com & LPT).
3. New Cyber port(s) should be listed.
DOS/Windows 3.1x Driver Installation
1. Insert the Driver Installation diskette, from the C: prompt, type
in copy a:\dos\*.*,then press <Enter>.
2. Type in edit autoexec.bat, then press <Enter>.
3. Add C:\CB20XPC.exe at the bottom of the autoexec.bat file.
4. Go to File, save the changes and exit.
5. Remove the diskette and restart the system for the new setup to
take effect.

Technical Support
QUESTIONS? SIIG’s Online Support has the answers! Simply
visitour web site at www.siig.com and click onSupport/Drivers.
Our online support database is updated daily with new drivers
and solutions. The answers to your problems could be just a few
clicks away.
Return Merchandise Authorization (RMA)
SIIGwarrantstotheoriginalbuyeroftheproductthatthehardware
isfree ofdefectsinmaterialsandworkmanshipforaperiod ofone,
twoorfiveyearsfromthedate of purchase. If your productfailsto
be in good working order during the warranty period, you may
return it to SIIG for repair or replacement at SIIG's option.
To return the product, you need to follow these steps.
Step 1: Contact SIIG's RMA Department
ToobtainanRMAnumber,SIIG'sRMADepartmentcanbereached
by phone at [phone] or fax at [phone] or email at
[email protected]. In order to issue an RMA number, the product
serialnumber isrequired. Thisnumbercanbe foundonthesideof
the box and on the back of the product.
Step 2: Complete the RMA form
• FilloutyourReturnMerchandiseAuthorization(RMA)form,and
include it in the package with the product.
• Properlypacktheproductforshipping. Allsoftware,cable(s)and
other accessories that came with the original package must be
included.
• ClearlywriteyourRMAnumberonthetopofthereturnedpackage
and on the accompanying RMA form.
SIIGwillrefusetoacceptanyshippingpackage,and will not
beresponsibleforaproductreturnedwithoutanRMAnumber
posted on the outside of the shipping carton.
Step 3: Ship the Product
You are responsible for the cost of shipping back to SIIG at the
following address:
SIIG, Inc. RMA#_______________
6078 Stewart Ave.
Fremont, CA 94538
SIIGwillshiptherepairedor replaced product via UPSGroundor
US Mail at no cost to you.

PRODUCTNAME MODEL NUMBER
CyberSerial POS 4000RJ IO1018
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC NOTICE:
This equipment has been tested and found to comply with the limits for a
ClassB digitaldevice,pursuant topart15 ofthe FCCRules.These limitsare
designed to provide reasonable protection against harmful interference in a
residentialinstallation.Thisequipmentgenerates,uses,andcanradiateradio
frequency energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However,thereisnoguaranteethatinterferencewillnotoccurinaparticular
installation. If this equipment does cause harmful interference to radio and
television reception, which can be determined by turning the equipment off
andon,theuserisencouragedtotrytocorrecttheinterferencebyoneormore
of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio or TV technician for help
Caution:
Any changes or modifications not expressly approved by the party
responsibleforcompliancecouldvoid theuser'sauthoritytooperate
this equipment
THE PARTY RESPONSIBLE FOR
PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Ave.
Fremont, CA 94538-3152
CyberSerial POS 4000RJ is a trademark of SIIG, Inc.
SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft, Windows and Windows
NT are registered trademarks of Microsoft Corporation. Pentium is a registered trademark of
Intel Corporation. Other names used in publication are for identification only and may be
trademarks of their respective companies.
December, 2001 Copyright ©2001 by SIIG, Inc. All rights reserved.