SIIG SC-SB6412 User manual

1
Introducing the Data Security Bay-64
The Data Security Bay-64 is an affordable DES (64-bit) real-time
hardware data encryption/decryption solution for your data
protection.
Features and Benefits
• Equipped with National Institute of Standards and
Technology (NIST) certified DES (64-bit) real-time
encryption/decryption hardware engine
• Capable of maneuvering 1.1 Gbps throughput without
taking extra CPU time and system resources
• Easy-Front-Access and fits into either 3.5" or 5.25" (with
included mounting rack) device bay
• An affordable real-time encryption/decryption solution
encrypts the entire hard drive contents including boot sector
and operating system without performance degradation
• All disk write (encryption) and disk read (decryption)
operations are completely transparent to users
• Two personal security keys included for authentication
• Operating system independent. No driver required!
• Works with various brands of Ultra ATA 133/100/66/33
hard disk drives and achieves data transfer rates up to
100 MB/sec
System Requirements
• Pentium or equivalent PC with one available 3.5" or 5.25"
device bay
• On-board or add-on Ultra ATA (IDE) interface
• Windows 98/98SE/ME/NT4.0/2000/XP
Data Security Bay-64
Quick Installation Guide
04-0285B

2
Package Contents
• (1) Data Security Bay-64
• (1) 5.25" mounting rack
• (2) Security Keys (identical)
• (1) 40-pin/80-wire Ultra ATA cable
• (1) "Y" split power cable & installation kit
• This quick installation guide
Layout
Figure 1. Layout
Default Jumper Settings
Security Key
Slot Activity
LED
IDE Controller
Connector
Hard Disk Drive
Connector
Power
Connector JP1 JP2
Figure 2. Default Jumper Settings
JP1 JP2

3
Jumper Setting Configurations
JP1
1-2 Disable
Encrypt/Decrypt
2-3 Enable Encrypt/Decrypt
(Default)
JP2
1-2 Slave
2-3 Master
(Default)
Figure 3. Jumper Setting Configurations
5.25" Mounting Rack Assembly
Note: Use the Mounting Rack Assembly only when installing into
a 5.25" drive bay.
Figure 4. 5.25" Mounting Rack Assembly

4
Installation
ThisDataSecurityBay-64onlysupportsonesecuredharddiskdrive.
Do not connect two hard disk drives to this controller.
The hard disk drive connected to this controller is only available if
the Security Key is inserted during boot process. You can remove
this key after Windows has completed booting and still have
complete access to information on this drive. On the other hand,
if the Security Key is NOT inserted during the boot proccess, the
hard disk drive will not be seen by your system.
Note: Static Electricity Discharge may permanently damage your
system. Discharge any static electricity build up in your body by
touching your computer’s case for a few seconds. Avoid any
contact with internal parts and handle cards only by their external
edges.
Configuring the Bay-64
1. Remove the sticker on the buzzer.
Note: The buzzer will make noise if a 1394 device, other than
the Security Key, is connected to the security key slot.
2. Set JP1 (see figure 3) to enable/disable encrypt/decrypt.
3. Set JP2 (see figure 3) to master/slave setting.
Note: Make sure JP2 is set to Master to enable encrypt/
decrypt.
Configuring the Hard Disk Drive
1. Always set the hard disk drive to master whenever you want
to encrypt/decrypt the hard disk drive.
2. Make sure you are starting with a new hard disk drive or
backup all of your data if you want to use an existing hard
disk drive.
Installing the Bay-64
1. Select an available 3.5" or 5.25" device bay for the Bay-64,
remove the cover plate from the selected device bay.
Note: When installing into a 5.25" device bay, mount the
Bay-64 into the 5.25" adapter first and follow the same
instructions. See Figure 4, 5.25" Mounting Rack Assembly.

5
2. Connect one end of the provided IDE cable to the IDE
Controller Connector (see below) on the Bay-64.
3. With a separate IDE cable (not provided), connect one end of
the cable to the Hard Disk Drive Connector (see below) on
the Bay-64.
4. Slide the Bay-64 into the device bay. Do not secure it at this
time.
5. Connect the IDE Controller Connector IDE cable (from #2
above) to the IDE controller on the motherboard or an add-
on controller.
6. Connect Hard Disk Drive Connector IDE cable (from #3
above) to your hard disk drive.
7. Connect a mini power connector (same type of power
connector used for the floppy drive) to the Power Connector
(see below) on the Bay-64. Use the included "Y" split power
cable if your system doesn't have an available mini power
connector.
Figure 5. Device Connections
8. Verify your device connections, then secure the Bay-64 to the
device bay using the provided installation kit.
IDE Controller
Connector
Hard Disk Drive
Connector
Power
Connector

6
Mounting
Screw
Figure 6. Mounting the Bay-64
9. Replace the computer cover and attach the power cord.
10. Insert your Security Key into the Security Key Slot and
power up your system.
11. Follow the regular procedures to partition and format the
hard disk drive.
Note: For existing hard disk drive with information, make
sure to back up information on this hard disk drive prior to
partition and format.
Important RMA Notice:
Theharddiskdrivethat'sencrypted/decryptedbyagiven Security
Key will only be recognized by that key. If you need to exchange
this product for any reason, do NOT send the keys in. Your hard
disk drive will only be recognized by the original key(s) that you
used to encrypt/decrypt it with.

7
Technical Support
QUESTIONS? SIIG’s Online Support has the answers! Simply
visit our web site at www.siig.com and click SUPPORT. Our
online support database is updated daily with new drivers and
solutions. The answers to your problems could be just a few clicks
away.
Return Merchandise Authorization (RMA)
SIIGwarrantstotheoriginal buyer of the product that the hardware
is free of defects in materials and workmanship for a period of one,
two or five years from the date of purchase. If your product fails to
be in good working order during the warranty period, you may
return it to SIIG for repair or replacement at SIIG's option.
To return the product, you need to follow these steps.
Step 1: Contact SIIG's RMA Department
To obtain an RMA number, SIIG's RMA Department can be
reached by phone at [phone] or fax at [phone] or email
at[email protected]. In order to issue an RMA number, the product
serial number is required. This number can be found on the side
of the box and on the back of the product.
Step 2: Complete the RMA form
• Fill out your Return Merchandise Authorization (RMA)
form, and include it in the package with the product.
• Properly pack the product for shipping. All software,
cable(s) and other accessories that came with the original
package must be included.
• Clearly write your RMA number on the top of the returned
package and on the accompanying RMA form.
SIIG will refuse to accept any shipping package, and will not
beresponsibleforaproductreturned without an RMAnumber
posted on the outside of the shipping carton.
Step 3: Ship the Product
You are responsible for the cost of shipping back to SIIG at the
following address:
SIIG, Inc. RMA#_______________
6078 Stewart Ave.
Fremont, CA 94538
SIIG will ship the repaired or replaced product via UPS Ground or
US Mail at no cost to you.

UK Warranty & Support Information
The 5 year warranty supplied with this product is offered by SIIG,
Inc. If you should happen to encounter any problems with this
product, please follow the procedures below.
1. If it is within the first year of purchase, please return product
to the outlet you purchased from.
2. If your product is between 2 and 5 years old from date of
purchase, please contact SIIG using the contact details below.
For UK Technical Support
Telephone: [phone]
Fax: [phone]
Email: [email protected]
Website: http://www.siig.uk.com
PRODUCT NAME MODEL NUMBER
Data Security Bay-64 CN2506
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR
PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Ave.
Fremont, CA 94538-3152
Data Security Bay-64 is a trademark of SIIG, Inc.
SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are registered
trademarks of Microsoft Corporation. Pentium is a registered trademark of Intel Corporation.
Other names used in publication are for identification only and may be trademarks of their
respective companies.
December, 2002 Copyright ©2002 by SIIG, Inc. All rights reserved.