Silhouette SPECIAL GLAZING BOX P0032 User manual

NEW UTENSILS
for
ADVANCED
Glazing Possibilities
____
SPECIAL GLAZING BOX P0032

CONTENT VH 66
Folie
1. Box P 0032 completely filled …………………………………….………………………………………………… 3
2. Why a new special glazing box? Target of these new utensils …………………………………..…… 4
3. BLS-Cutter – Advantages ………………………………………………………………………………..…………… 5
4. BLS-Cutter – Use ………..…………………………………………………………………………………..………..… 6
5. Inclination lever for Plug-Wave-Hinge – Advantage ……………………………………………………… 7
6. Inclination lever – Use ……………………………….………………………..………………………..……………... 8
7. New BLS for special situations …….. .…………………………………………………………..……………….. 9

1. BOX COMPLETELY FILLED
BLS-CUTTER (AC 392)
P 0000 11 0392 0000
Substitute blade: P 0000 44 0693 0000
INCLINATION LEVER (AC 400)
P 0000 11 0400 0000
SPECIAL-BLS (Glazing
Sleeves)
BLS 96 „large“
P 0000 22 0096 0000 (50 pcs.)
BLS 97 „short“
P 0000 22 0097 0000 (50 pcs.)
BLS 98 „long“
P 0000 22 0098 0000 (50 pcs.)
INSTRUCTIONS VH 66
P 0000 26 2801 0066
SPECIAL GLAZING BOX P 0032
P 0032 00 0000 0000

As a specialist for rimless drilled frames, Silhouette offers the best possible
Solutions also for exceptional glazing situations:
Situation Solution
Crosscutting of BLS with scalpel requires accuracy and skill.
The BLS-Cutter will simplify and improve this kind of work.
BLS-Cutter
Disc hinges can easily get loose during inclination.
The new tool will relieve the hinges during inclination.
Inclination Lever
When lens drills get too big, the frame fit often gets loose.
In this case drill holes must be drilled out to 1,6 mm and this new
BLS must be inserted. This will fix shaky frames again.
BLS „large“
PLUS-lenses often get thinner than planned. As a result the fixing
pins of the frame part are too long.
The new BLS hides the long pin in the higher BLS-head.
BLS „short“
MINUS-lenses are often too thick for the length of standard-BLS.
The new, extra-long BLS makes glazing of thicker lenses possible.
BLS „long“
2. WHY A NEW SPECIAL GLAZING BOX?
TARGET OF THESE NEW UTENSILES

3. „BLS-CUTTER“ - ADVANTAGES
SAFETY: no scratching of prescription lenses
TIME SAVING: straight, smooth cut within seconds
COMFORT: easy crosscutting of BLS
LABOUR SAVING: no protection foil necessary, therefore no taping, no puncturing
QUALITY: perfect glazing result through perfect cut
AC 392
Easy crosscutting of BLS (glazing sleeves) with 1,4 mm

1. Press BLS (glazing
sleeve) into lens
drilling to the stop.
4. „BLS-CUTTER“ - USE
3. Crosscut BLS by pressing
the Cutter („Guillotine“)
together.
4. Mount frame parts as
usual.
2. Place BLS-Cutter on
excess length of BLS.
BLS-Cutter
AC 392
2 31

INCLINATION LEVER AC 400
Makes easy inclination possible through high transmission of forces .
Relieves plastic discs in hinge, so that they are not damaged.
5. INCLINATION LEVER for DISC-HINGE
Disc-Hinge

6. INCLINATION LEVER - USE
Hold lens fixation firmly. Either manually (nylor, fullrim) or with mounting pliers
P0026 (rimless). Close temple by approx 30°. Place inclination lever on side part
and hinge and adjust inclination angle as required.

STANDARD
BLS 58
NEW
BLS 96
„large“
NEW
BLS 97
„short“
NEW
BLS 98
„long“
Standard Glazing for too big drills for very thin
lenses
for very thick
lenses
2,0 – 6,5 mm 2,0 – 6,5 mm 1,3 – 3 mm 6 – 9,5 mm
1,4 mm 1,6 mm 1,4 mm 1,4 mm
Lens size
7. NEW BLS for SPECIAL SITUATIONS