Silicon Laboratories C8051F35 Series User manual

Rev. 0.3 9/06 Copyright © 2006 by Silicon Laboratories C8051F35x-DK
C8051F35x-DK
C8051F35XDEVELOPMENT KIT USER’SGUIDE
1. Kit Contents
The C8051F35x Development Kit contains the following items:
• C8051F350 Target Board
• C8051Fxxx Development Kit Quick-Start Guide
• Silicon Laboratories IDE and Product Information CD-ROM. CD content includes:
• Silicon Laboratories Integrated Development Environment (IDE)
• Keil 8051 Development Tools (macro assembler, linker, evaluation ‘C’ compiler)
• Source code examples and register definition files
• Documentation
• C8051F35x Development Kit User’s Guide (this document)
• AC to DC Power Adapter
• USB Debug Adapter (USB to Debug Interface)
• USB Cable
2. Hardware Setup using a USB Debug Adapter
The target board is connected to a PC running the Silicon Laboratories IDE via the USB Debug Adapter as shown
in Figure 1.
1. Connect the USB Debug Adapter to the DEBUG connector on the target board with the 10-pin ribbon cable.
2. Connect one end of the USB cable to the USB connector on the USB Debug Adapter.
3. Connect the other end of the USB cable to a USB Port on the PC.
4. Connect the ac/dc power adapter to power jack P1 on the target board.
Notes:
•UsetheReset button in the IDE to reset the target when connected using a USB Debug Adapter.
• Remove power from the target board and the USB Debug Adapter before connecting or disconnecting the
ribbon cable from the target board. Connecting or disconnecting the cable when the devices have power can
damage the device and/or the USB Debug Adapter.
Figure 1. Hardware Setup using a USB Debug Adapter
PC
USB
Cable
USB Debug Adapter
AC/DC
Adapter
Target Board
SILICON LABORATORIES
PWR
P1.6
P3.7RESET
Port 4Port 3Port 1
Port 2 Port 0
MCU
Silicon Laboratories
USB DEBUG ADAPTER
Run
StopPower
Downloaded from Elcodis.com electronic components distributor

C8051F35x-DK
2 Rev. 0.3
3. Software Setup
The included CD-ROM contains the Silicon Laboratories Integrated Development Environment (IDE), Keil software
8051 tools and additional documentation. Insert the CD-ROM into your PC’s CD-ROM drive. An installer will auto-
matically launch, allowing you to install the IDE software or read documentation by clicking buttons on the Installa-
tion Panel. If the installer does not automatically start when you insert the CD-ROM, run autorun.exe found in the
root directory of the CD-ROM. Refer to the readme.txt file on the CD-ROM for the latest information regarding
known IDE problems and restrictions.
4. Silicon Laboratories Integrated Development Environment
The Silicon Laboratories IDE integrates a source-code editor, source-level debugger and in-system Flash program-
mer. The use of third-party compilers and assemblers is also supported. This development kit includes the Keil
Software A51 macro assembler, BL51 linker and evaluation version C51 ‘C’ compiler. These tools can be used
from within the Silicon Laboratories IDE.
4.1. System Requirements
The Silicon Laboratories IDE requirements:
• Pentium-class host PC running Microsoft Windows 98SE or later.
• One available COM or USB port.
• 64 MB RAM and 40 MB free HD space recommended.
4.2. Assembler and Linker
A full-version Keil A51 macro assembler and BL51 banking linker are included with the development kit and are
installed during IDE installation. The complete assembler and linker reference manual can be found under the Help
menu in the IDE or in the “SiLabs\MCU\hlp” directory (A51.pdf).
4.3. Evaluation C51 ‘C’ Compiler
An evaluation version of the Keil C51 ‘C’ compiler is included with the development kit and is installed during IDE
installation. The evaluation version of the C51 compiler is the same as the full professional version except code
size is limited to 4 kB and the floating point library is not included. The C51 compiler reference manual can be
found under the Help menu in the IDE or in the “SiLabs\MCU\hlp” directory (C51.pdf).
4.4. Using the Keil Software 8051 Tools with the Silicon Laboratories IDE
To perform source-level debugging with the IDE, you must configure the Keil 8051 tools to generate an absolute
object file in the OMF-51 format with object extensions and debug records enabled. You may build the OMF-51
absolute object file by calling the Keil 8051 tools at the command line (e.g. batch file or make file) or by using the
project manager built into the IDE. The default configuration when using the Silicon Laboratories IDE project
manager enables object extension and debug record generation.
Refer to Applications Note AN104 - Integrating
Keil 8051 Tools Into the Silicon Labs IDE
in the “SiLabs\MCU\Documentation\Appnotes” directory on the CD-
ROM for additional information on using the Keil 8051 tools with the Silicon Laboratories IDE.
To build an absolute object file using the Silicon Laboratories IDE project manager, you must first create a project. A
project consists of a set of files, IDE configuration, debug views, and a target build configuration (list of files and tool
configurations used as input to the assembler, compiler, and linker when building an output object file).
The following sections illustrate the steps necessary to manually create a project with one or more source files, build
a program and download the program to the target in preparation for debugging. (The IDE will automatically create a
single-file project using the currently open and active source file if you select
Build/Make Project before a project is
defined.)
Downloaded from Elcodis.com electronic components distributor

C8051F35x-DK
Rev. 0.3 3
4.4.1. Creating a New Project
1. Select Project→New Project to open a new project and reset all configuration settings to default.
2. Select File→New File to open an editor window. Create your source file(s) and save the file(s) with a rec-
ognized extension, such as .c, .h, or .asm, to enable color syntax highlighting.
3. Right-click on “New Project” in the Project Window. Select Add files to project. Select files in the file
browser and click Open. Continue adding files until all project files have been added.
4. For each of the files in the Project Window that you want assembled, compiled and linked into the target
build, right-click on the file name and select
Add file to build . Each file will be assembled or compiled as
appropriate (based on file extension) and linked into the build of the absolute object file.
Note: If a project contains a large number of files, the “Group” feature of the IDE can be used to organize.
Right-click on “New Project” in the
Project Window . Select Add Groups to project . Add pre-defined
groups or add customized groups. Right-click on the group name and choose
Add file to group . Select files
to be added. Continue adding files until all project files have been added.
4.4.2. Building and Downloading the Program for Debugging
1. Once all source files have been added to the target build, build the project by clicking on the Build/Make
Project button in the toolbar or selecting Project→Build/Make Project from the menu.
Note: After the project has been built the first time, the Build/Make Project command will only build the
files that have been changed since the previous build. To rebuild all files and project dependencies, click
on the Rebuild All button in the toolbar or select Project→Rebuild All from the menu.
2. Before connecting to the target device, several connection options may need to be set. Open the
Connection Options window by selecting Options → Connection Options... in the IDE menu. First, select
the appropriate adapter in the “Serial Adapter” section. Next, the correct “Debug Interface” must be selected.
C8051F35x family devices use the Silicon Labs 2-wire (C2) debug interface. Once all the selections are
made, click the OK button to close the window.
3. Click the
Connect button in the toolbar or select Debug → Connect from the menu to connect to the device.
4. Download the project to the target by clicking the Download Code button in the toolbar.
Note: To enable automatic downloading if the program build is successful select Enable automatic con-
nect/download after build in the Project→Target Build Configuration dialog. If errors occur during the
build process, the IDE will not attempt the download.
5. Save the project when finished with the debug session to preserve the current target build configuration,
editor settings and the location of all open debug views. To save the project, select Project->Save Project
As... from the menu. Create a new name for the project and click on Save.
Downloaded from Elcodis.com electronic components distributor

C8051F35x-DK
4 Rev. 0.3
5. Example Source Code
Example source code and register definition files are provided in the “SiLabs\MCU\Examples\ C8051F35x ” directory
during IDE installation. These files may be used as a template for code development. Example applications include
a blinking LED example which configures the green LED on the target board to blink at a fixed rate.
5.1. Register Definition Files
Register definition files C8051F350.inc and C8051F350.h define all SFR registers and bit-addressable control/
status bits. They are installed into the “SiLabs\MCU\Examples\C8051F35x” directory during IDE installation. The
register and bit names are identical to those used in the C8051F35x data sheet. Both register definition files are
also installed in the default search path used by the Keil Software 8051 tools. Therefore, when using the Keil 8051
tools included with the development kit (A51, C51), it is not necessary to copy a register definition file to each
project’s file directory.
5.2. Blinking LED Example
The example source files blink.asm and blinky.c show examples of several basic C8051F35x functions. These
include; disabling the watchdog timer (WDT), configuring the Port I/O crossbar, configuring a timer for an interrupt
routine, initializing the system clock, and configuring a GPIO port. When compiled/assembled and linked this pro-
gram flashes the green LED on the C8051F350 target board about five times a second using the interrupt handler
with a C8051F350 timer.
Downloaded from Elcodis.com electronic components distributor

C8051F35x-DK
Rev. 0.3 5
6. Target Board
The C8051F35x Development Kit includes a target board with a C8051F350 device pre-installed for evaluation and
preliminary software development. Numerous input/output (I/O) connections are provided to facilitate prototyping
using the target board. Refer to
Figure 2 for the locations of the various I/O connectors.
P1 Power connector (accepts input from 7 to 15 VDC unregulated power adapter)
J1 22-pin Expansion I/O connector
J3 Port I/O Configuration Jumper Block
J4 DEBUG connector for Debug Adapter interface
J5 DB-9 connector for UART0 RS232 interface
J6 Analog I/O terminal block
J7 Connector for IDAC0 voltage circuit
J8 USB Debug Adapter target board power connector
J9, J10 External crystal enable connectors
J11 Connector for IDAC1 voltage circuit
J12 Connector block for Thermistor circuitry
J13, J14 ADC external voltage reference connectors
Figure 2. C8051F350 Target Board
DEBUG
Pin 1
P1
J5
Prototype Area
Pin 1
J6
C8051
F35X
Prototyping Area & I/O Connection Points
J8
J4
Pin 2
Pin 1
J1
PWR P1.0 Reset
P0.6
P0.7
J2
J9 J10
J11 J7
Pin 1
Pin 2
J12
Pin 1 Pin 2
J3
J14
J13
Pin 1
Downloaded from Elcodis.com electronic components distributor

C8051F35x-DK
6 Rev. 0.3
6.1. System Clock Sources
The C8051F350 device installed on the target board features a calibrated programmable internal oscillator which is
enabled as the system clock source on reset. After reset, the internal oscillator operates at a frequency of
3.0625 MHz (±2%) by default but may be configured by software to operate at other frequencies. Therefore, in many
applications an external oscillator is not required. However, if you wish to operate the C8051F350 device at a fre-
quency not available with the internal oscillator, an external crystal may be used. Refer to the
C8051F35x data sheet
for more information on configuring the system clock source.
The target board is designed to facilitate the installation of an external crystal. Remove shorting blocks at headers
J9 and J10 and install the crystal at the pads marked Y1. Install a 10 MΩresistor at R9 and install capacitors at
C14 and C15 using values appropriate for the crystal you select. Refer to the C8051F35x data sheet for more infor-
mation on the use of external oscillators.
6.2. Switches and LEDs
Two switches are provided on the target board. Switch SW1 is connected to the RESET pin of the C8051F350.
Pressing SW1 puts the device into its hardware-reset state. Switch SW2 is connected to the C8051F350’s general
purpose I/O (GPIO) pin through headers. Pressing SW2 generates a logic low signal on the port pin. Remove the
shorting block from the jumper to disconnect SW2 from the port pins. The port pin signal is also routed to a pin on
the J1 I/O connector. See Table 1 for the port pins and headers corresponding to each switch.
Three LEDs are also provided on the target board. The red LED labeled PWR is used to indicate a power connec-
tion to the target board. The green LEDs labeled with port pin names are connected to the C8051F350’s GPIO pins
through headers. Remove the shorting blocks from the headers to disconnect the LEDs from the port pins. The port
pin signals are also routed to pins on the J1 I/O connector. See Table 1 for the port pins and headers correspond-
ing to each LED.
Table 1. Target Board I/O Descriptions
Description I/O Jumper
SW1 Reset none
SW2 P1.0 J3[5–6]
Green LED D2 P0.6 J3[1–2]
Green LED D1 P0.7 J3[3–4]
Red LED PWR none
Downloaded from Elcodis.com electronic components distributor

C8051F35x-DK
Rev. 0.3 7
6.3. Expansion I/O Connector (J1)
The 34 -pin Expansion I/O connector J1 provides access to all signal pins of the C8051F350 device. Pins for V
DD
and
GND as well as pins for VDDA and AGND are also available. A small through-hole prototyping area is also provided.
All I/O signals routed to connector J1 are also routed to through-hole connection points between J1 and the prototyp-
ing area (see
Figure 2 on page 5 ). Each connection point is labeled indicating the signal available at the connection
point. See
Table 2 for a list of pin descriptions for J1.
6.4. Target Board DEBUG Interface (J4)
The DEBUG connector (J4) provides access to the DEBUG (C2) pins of the C8051F350. It is used to connect the
Serial Adapter or the USB Debug Adapter to the target board for in-circuit debugging and Flash programming.
Table 3 shows the
DEBUG pin definitions.
6.5. Serial Interface (J5)
A RS232 transceiver circuit and DB-9 (J5) connector are provided on the target board to facilitate serial connec-
tions to UART0 of the C8051F350. The TX, RX, RTS and CTS signals of UART0 may be connected to the DB-9
connector and transceiver by installing shorting blocks on header J3.
J3[7–8] - Install shorting block to connect UART0 TX (P0.4) to transceiver.
J3[9–10] - Install shorting block to connect UART0 RX (P0.5) to transceiver.
J3[11–12] - Install shorting block to connect UART0 RTS (P1.4) to transceiver.
J3[13–14] - Install shorting block to connect UART0 CTS (P1.5) to transceiver.
Table 2. J1 Pin Descriptions
Pin # Description Pin # Description Pin # Description
1 V
DD
13 P1.2 25 AIN3
2 GND 14 P1.3 26 AIN4
3 P0.0 15 P1.4 27 AIN5
4 P0.1 16 P1.5 28 AIN6
5 P0.2 17 P1.6/IDAC0 29 AIN7
6 P0.3 18 P1.7/IDAC1 30 VREF+
7 P0.4 19 P2.0 31 /RST
8P0.5 20AGND 32VREF–
9P0.6 21
AGND 33 VDDA
10 P0.7 22 AIN0 34 AGND
11 P1.0 23 AIN1 - -
P1.1 24 AIN2 - -
Table 3. DEBUG Connector Pin Descriptions
Pin # Description
1 +3VD(+3.3VDC)
2, 3, 9 GND (Ground)
4C2D
5/RST(Reset)
6P3.0
7C2CK
8 Not Connected
10 USB Power
Downloaded from Elcodis.com electronic components distributor

C8051F35x-DK
8 Rev. 0.3
6.6. Analog I/O (J6)
Many of the C8051F350 target device’s port pins are connected to the J6 terminal block. Connections for VDDA,
AGND, ADC external voltage refences, IDAC outputs and ADC inputs are available. Refer to Table 4 for the J6 ter-
minal block connections.
6.7. IDAC Connectors (J7, J11)
The C8051F350 target board also features two Current-to-Voltage 1 KΩload resistors that may be connected to
the 10-bit current-mode Digital-to-Analog Converters (IDACs) on port pins P1.6 and P1.7. Install a shorting block
on J7 to connect the IDAC0/P1.6 pin of the target device to a load resistor. Install a second shorting block on J11 to
connect the IDAC1/P1.7 pin of the target device to a load resistor. The IDAC signals are then routed to the J1 and
J6 connectors.
6.8. USB Debug Adapter Target Board Power Connector (J8)
The USB Debug Adapter includes a connection to provide power to the target board. This connection is routed
from J4[10] to J8[1]. Place a shorting block at header J8[2-3] to power the board directly from an ac/dc power
adapter. Place a shorting block at header J8[1-2] to power the board from the USB Debug Adapter. Please note
that the second option is not supported with either the EC1 or EC2 Serial Adapters.
6.9. Thermistor Connector Block (J12)
A thermistor circuit is included on the board which allows for a ratiometric measurement of the included thermistor.
To use the circuit, remove the shorting blocks on the IDAC headers (J7, J11) and the External Voltage Reference
headers (J13, J14). Next, connect all of the signals on the thermistor connector block (J12). Software on the chip
can be written to use IDAC0 as a reference current source for the circuit. The current creates a voltage across R27
which is used as an external Voltage Reference input, while the voltage across the thermistor (R26) can be mea-
sured by connecting AIN0.0 to the AIN+ ADC input, and AIN0.1 to the AIN- ADC input.
6.10. External Voltage Reference (J13, J14)
A precision 2.5V voltage reference source is also included on the C8051F350 target board. To use this circuit as a
reference source for the ADC, place shorting block on headers J13 and J14. Note that software on the device
should be configured to use an external reference when using this configuration. When using the internal (on-chip)
reference source, headers J13 and J14 should be left open.
Table 4. J6 Terminal Block Pin Descriptions
Pin # Description Pin # Description
1IDAC0 8 AIN3
2IDAC1 9 AIN4
3 VREF+ 10 AIN5
4VREF– 11 AIN6
5 AIN0 12 AIN7
6AIN1 13AGND
7 AIN2 14 VDDA
Downloaded from Elcodis.com electronic components distributor

C8051F35x-DK
Rev. 0.3 9
7. Schematics
Figure 3. C8051F350 Target Board Schematic - Page 1
Downloaded from Elcodis.com electronic components distributor

C8051F35x-DK
10 Rev. 0.3
Figure 4. C8051F350 Target Board Schematic - Page 2
Downloaded from Elcodis.com electronic components distributor