Silvercrest SPBS 5000 B2 User manual

IAN 311969
POWER BANK WITH SOLAR CHARGER SPBS 5000 B2
POWER BANK WITH SOLAR CHARGER
Operating instructions
POWERBANK MET ZONNEPANEEL
Gebruiksaanwijzing
BATTERIE EXTERNE POWERBANK
AVEC FONCTION RECHARGE SOLAIRE
Mode d‘emploi
POWERBANK
MIT SOLARLADEFUNKTION
Bedienungsanleitung

GB/IE/NI Operating instructions Page 1
FR/BE Mode d'emploi Page 19
NL/BE Gebruiksaanwijzing Pagina 37
DE/AT/CH Bedienungsanleitung Seite 55
Before reading, unfold the page containing the illustrations and familiarise yourself with all
functions of the device.
Avant de lire le mode d'emploi, ouvrez la page contenant les illustrations et familiarisez-vous
ensuite avec toutes les fonctions de l'appareil.
Vouw vóór het lezen de pagina met de afbeeldingen open en maak u vertrouwd met alle
functies van het apparaat.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich
anschließend mit allen Funktionen des Gerätes vertraut.

GB│IE│NI │ 1 ■
SPBS 5000 B2
Contents
Introduction............................................2
Information concerning these operating instructions ......................2
Notes on trademarks ..............................................2
Intended use.....................................................2
Warnings and symbols used ........................................3
Safety ................................................4
Basic safety guidelines.............................................4
Description of components ...............................6
Operation .............................................7
Unpacking ......................................................7
Check the package contents ........................................7
Disposal of packaging materials .....................................7
Attaching the suction cups ..........................................8
Charging with the solar panel ......................................10
Charging with the charger cable ....................................10
Handling and operation.................................11
Switch the device on/off ..........................................11
Display charge level..............................................11
Compatible devices ..............................................12
Charging external devices .........................................12
Troubleshooting .......................................13
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Storage when not in use ................................14
Disposal..............................................14
Appendix.............................................15
Technical data ..................................................15
Notes on the EU Declaration of Conformity............................15
Kompernass Handels GmbH warranty ...............................16
Service ........................................................18
Importer .......................................................18

■ 2 │ GB│IE│NI SPBS 5000 B2
Introduction
Information concerning these operating instructions
Congratulations on the purchase of your new device.
You have selected a high-quality product. The operating instructions are part of this
product. They contain important information about safety, usage and disposal.
Before using the product, familiarise yourself with all operating and safety instruc-
tions. Use the product only as described and for the specified areas of application.
Keep these operating instructions as a reference and store them near the product.
Please also pass on these operating instructions to any future owner.
Notes on trademarks
■ USB®is a registered trademark of USB Implementers Forum, Inc.
■ The SilverCrest trademark and the retail name are the property of their respec-
tive owner.
All other names and products may be trademarks or registered trademarks of their
respective owners.
Intended use
This information technology device is designed solely for the charging of batteries
in mobile phones, MP3 players, digital cameras or other battery-powered devices
that feature a USB connection as standard. To do this, the device converts sunlight
into electrical energy and stores it in its internal battery. The device is not intended
for any other purpose, nor for use beyond the scope described. The device is not
intended for use in commercial or industrial environments. The manufacturer ac-
cepts no responsibility for damage caused by failure to observe these instructions,
improper use or repairs, unauthorised modifications or the use of unapproved
replacement parts. The risk shall be borne solely by the user.

GB│IE│NI │ 3 ■
SPBS 5000 B2
Warnings and symbols used
The following warning notice types are used in these operating instructions:
DANGER
A warning notice at this hazard level indicates a potentially
hazardous situation.
Failure to avoid this hazardous situation could result in severe injuries or even
death.
► Follow the instructions in this warning notice to avoid the risk of serious
injuries or death.
WARNING
A warning at this hazard level indicates a potentially
hazardous situation.
Failure to avoid this hazardous situation could result in injury.
► Follow the instructions on this warning label to prevent injury.
CAUTION
A warning notice at this hazard level indicates a potential for
property damage.
Failure to avoid this situation could result in property damage.
► Follow the instructions in this warning notice to prevent property damage.
NOTE
► A note provides additional information that will assist you in using the device.
This symbol can be found on the housing of the power bank and
indicates that the operating instructions should be followed.

■ 4 │ GB│IE│NI SPBS 5000 B2
Safety
This product complies with statutory safety regulations. Improper use may result in
personal injury and property damage.
Basic safety guidelines
To ensure safe operation of the product, follow the safety guidelines set out below:
■ Check the device for visible external damage before use.
Do not operate a device that has been damaged or dropped.
■ This device may be used by children aged 8 years and above and by persons
with limited physical, sensory or mental capabil-
ities, or lack of experience and knowledge, provided that they are under su-
pervision or have been told how to use the device safely and are aware of the
potential risks. Children must not use the device as a plaything. Cleaning and
user maintenance tasks may not be carried out by children unless they are
supervised.
■ DANGER! Do not allow children to play with the packaging material! Keep
all packaging materials away from children.
Risk of suffocation!
■ Never put items containing liquid (such as vases or open drinks) on or next to
the device.
■ WARNING! Be sure to provide sufficient air circulation to avoid a heat
build-up. Never cover the device! Risk of fire!
■ WARNING! Never operate the device in the vicinity of naked flames (e.g.
candles), and do not place burning candles on or next to the device. This will
help to prevent fires.
■ Do not operate the device near heat sources such as radiators or other
heat-generating devices.

GB│IE│NI │ 5 ■
SPBS 5000 B2
■ Never expose the device to extreme heat. This particularly applies to storage in
a car. Extreme temperatures can occur in car interiors and glove compartments
during long periods of immobilisation. Remove electrical and electronic devices
from the vehicle.
■ Never open the housing of the device.
There are no user-serviceable or replaceable components inside the device.
■ Do not make any unauthorised modifications or alterations to the device.
■ All repairs must be carried out by authorised specialist companies or by the
Customer Service department. Improper repairs may put the user at risk. It will
also invalidate any warranty claims.
■ Repairs to the device during the warranty period may only be carried out by
a customer service department authorised by the manufacturer. Otherwise, no
warranty claims will be held for any subsequent damages.
■ WARNING! Switch the device off immediately and disconnect any con-
nected charging cables from the device if you smell fumes or notice any smoke.
Have the device checked by a qualified specialist before using it again.
■ If you are using a USB power supply, the mains socket used must always be
easily accessible so that the USB power supply can be quickly disconnected
from the socket in a hazardous situation. You should also observe the operating
instructions for the USB power supply.
■ WARNING! Mishandling the batteries can cause fires, explosions, leakag-
es or other hazards! Do not throw the device into a fire, since the integrated
battery may explode.
■ Comply with all conditions for and prohibitions on use for battery-powered de-
vices in locations with specific hazard risks, such as petrol stations, aeroplanes,
hospitals, etc.

■ 6 │ GB│IE│NI SPBS 5000 B2
Description of components
(See fold-out page for illustrations)
Solar panel
Solar LED
LED (5V USB active output)
ON/OFF button
Charge level LEDs
Protective cover
USB port (output: 5 V , 2100 mA)
Micro-USB port (input: 5 V , 2100 mA)
Brackets for suction cups
Suction cups
Charger cable (USB to micro USB)
Operating instructions (Symbol image)

GB│IE│NI │ 7 ■
SPBS 5000 B2
Operation
Unpacking
♦ Remove all parts and the operating instructions from the packaging.
♦ Remove all packaging material.
Check the package contents
(See fold-out page for illustrations)
The product includes the following components:
▯ Power Bank with Solar Charger SPBS 5000 B2
▯ Charger cable
▯ 2 x brackets for suction cups
▯ 4 x suction cups
▯ These operating instructions
NOTE
► Check the package for completeness and for signs of visible damage.
► If the delivery is incomplete or damage has occurred as a result of defec-
tive packaging or during transport, contact the Service hotline (see section
Service).
Disposal of packaging materials
The packaging materials have been selected for their environmental
friendliness and ease of disposal and are therefore recyclable.
Dispose of packaging materials that are no longer needed in
accordance with applicable local regulations.
Dispose of the packaging in an environmentally friendly manner.
Note the labelling on the packaging and separate the packaging
material components for disposal if necessary. The packaging
material is labelled with abbreviations (a) and numbers (b) with the
following meanings:
1–7: Plastics,
20–22: Paper and cardboard,
80–98: Composites.

■ 8 │ GB│IE│NI SPBS 5000 B2
Attaching the suction cups
NOTE
► To make sure that the suction cups hold firmly, the surface must be com-
pletely free of dust, oil and grease.
Variant A
Variant A is suitable for attaching the device to a flat, level surface.
♦ Attach all four suction cups to the underside of the device, as shown in
“Figure A”.
♦ Push the suction cups into the large holes.
♦ Now fasten the suction cups by sliding them into the narrow openings.
Figure A
♦ You can now attach the device on a flat, level using the suction cups .

GB│IE│NI │ 9 ■
SPBS 5000 B2
Variant B
Variant B is suitable for attaching the device to a pane of glass.
♦ Attach the four suction cups to the two brackets ,as shown in “Figure B”.
♦ Push the suction cups into the large holes.
♦ Now fasten the suction cups by sliding them into the narrow openings.
♦ Now mount the brackets on the underside of the device by pushing the
retaining lugs into the corresponding slots on the rear of the device and locking
them in place.
Figure B
♦ You can now attach the device to a pane of glass using the suction cups .

■ 10 │ GB│IE│NI SPBS 5000 B2
Charging with the solar panel
CAUTION
► Ensure that the ambient temperature does not exceed 35°C. This is particu-
larly important when using the device inside a motor vehicle.
You can charge the battery of the power bank with the solar panel .
Ensure that the solar panel is receiving sufficient sunlight. As soon as there is
sufficient sunlight, the solar LED lights up orange to show that the battery is
being charged. If the solar LED does not light up, there is not enough sunlight
available. In this case, change the location of the device or place the device in
direct sunlight. Once the solar LED lights up green, the battery is fully charged.
Charging with the charger cable
If there is no sunlight available, you can charge the power bank battery with the
charger cable .
CAUTION!
► Charge the device only in dry interior rooms as the device is not adequately
protected against water spray when the protective cover is removed.
► Due to the high current consumption, the power bank must be charged using
a USB mains adapter (not supplied). Do not charge the power bank via the
USB port of a PC or notebook.
► Use only a USB mains adapter with an output voltage of 5 V and an output
current of at least 2.1 A to charge the power bank.
► Use only the supplied charger cable to charge the power bank!
► Always disconnect the charger cable when charging is complete and
replace the protective cover .
♦ Open the protective cover and connect the micro-USB plug of the charger
cable to the device’s micro-USB port .
♦ Connect the USB plug of the charger cable to the USB connection of a
USB mains adapter.

GB│IE│NI │ 11 ■
SPBS 5000 B2
A rough estimate of the charge level is shown during charging by means of the
charge level LEDs .
Charge level LEDs Charge level
One LED is flashing < 25%
One LED is on, the second LED is flashing 25–49%
Two LEDs are on, the third LED is flashing 50–74%
Three LEDs are on, the fourth LED is flashing 75–99%
All LEDs are on 100%
Handling and operation
Switch the device on/off
Switching on
♦ Press the ON/OFF button briefly to switch on the power bank. The charge
level LEDs light up for about 15 seconds.
The LED lights up blue as long as a connected device is being charged.
Automatic switch-off
♦ If no device is connected for charging within 15 seconds, the power bank
switches off automatically to conserve its battery.
Switching off
♦ Press and hold the ON/OFF button for at least 2 seconds to switch off the
power bank and stop the charging process. The LED goes out.
Display charge level
♦ Press the ON/OFF button briefly to show the charge level of the non-loaded
battery for a few seconds. The charge level LEDs provide you with informa-
tion about the approximate charge level.
Charge level LEDs Charge level
All LEDs are on 75 -100 %
Three LEDs are on 50 -74 %
Two LEDs are on 25 -49 %
One LED is on 5 -24 %
One LED is flashing < 5 %
All LEDs off 0 %

■ 12 │ GB│IE│NI SPBS 5000 B2
Compatible devices
You can use the power bank to charge end devices that require a charging current
of at least 70 mA and a maximum of 2,1A.
If the connected end device requires a current of less than 70 mA or more than
2,1A, the power bank will switch itself off immediately after being switched on
with the ON/OFF button . In this case, check the power bank’s suitability for
your end device on the basis of the technical data of your end device.
NOTE
► If the device switches off automatically due to overloading, it can only be
switched back on if it has been charged for a short time beforehand with a
USB mains adapter. The device has switched itself off automatically due to
overloading.
Charging external devices
Connect the charging cable of your end device to the USB port on the power
bank and to your end device.
♦ If charging does not start automatically, press the ON/OFF button briefly to
start the charging process.
The LED lights up for as long as the connected device is being charged.
Once your device is fully charged, the power bank switches off. To interrupt the
charging process, you can disconnect the end device. If your end device is not
fully charged and the LED goes out during charging, this means the power
bank’s battery is discharged. The power bank’s battery must be recharged again
before you can charge end devices.

GB│IE│NI │ 13 ■
SPBS 5000 B2
Troubleshooting
A connected device is not charging.
♦ Press the ON/OFF button briefly to start the charging process.
♦ The power bank’s battery is empty. Charge the battery.
♦ No connection to the device. Check the connection.
♦ The power bank can be used for end devices that require a charging current
of no more than 2,1A. If the connected end device requires a current of
more than 2,1A, the power bank will switch itself off immediately after being
switched on with the ON/OFF button . In this case, check the power bank’s
suitability for your end device on the basis of the technical data of your end
device.
♦ Devices that require a charging current of less than 70 mA will not be charged
or only partially charged.
The power bank will not switch on.
♦ The power bank has switched itself off automatically due to overloading. You
need to charge the power bank for a short while with a USB mains adapter
before you can switch the power bank back on.
The power bank’s battery is not charging via the solar panel.
♦ Check that the solar panel is receiving sufficient sunlight.
NOTE
► If the above-mentioned solutions do not resolve the problem, please contact
Customer Service (see chapter Service).

■ 14 │ GB│IE│NI SPBS 5000 B2
Cleaning
CAUTION
► To avoid irreparable damage to the device, ensure that no moisture can
penetrate the device during cleaning. Ensure that the connection sockets
(+ ) are closed off properly with the protective cover .
► Do not use caustic, abrasive or solvent-based cleaning materials. These can
damage the surfaces of the device.
NOTE
► A contaminated solar panel will not deliver full performance.
♦ Clean the surfaces of the device and the solar panel with a soft, dry cloth. For
stubborn dirt, use a slightly damp cloth with a mild detergent.
Storage when not in use
♦ If you do not intend to use the device for a long time, store it in a clean, dry
place away from direct sunlight.
♦ If the power bank is not going to be used for some time, the battery should be
recharged at regular intervals. This helps to preserve battery performance.
Disposal
The adjacent symbol of a crossed-out wheelie bin means that this
device is subject to Directive 2012/19/EU. This directive states that
this device may not be disposed of in the normal household waste at
the end of its useful life, but must be handed over to specially set-up
collection locations, recycling depots or disposal companies.
This disposal is free of charge for the user. Protect the environment
and dispose of this device properly.
Your local community or municipal authorities can provide information
on how to dispose of the worn-out product.

GB│IE│NI │ 15 ■
SPBS 5000 B2
Appendix
Technical data
Integrated battery (lithium polymer) 3.7V/5000mAh (18.5 Wh)
Input voltage/current 5 V (direct current), max. 2100 mA
Output voltage, current 5 V (direct current), max. 2100 mA
Minimum discharge current approx. 70 mA
Charging time, battery
— Solar panel
— Charger cable
approx. 22 – 30 hours*
approx. 3 – 4 hours**
Protection type IP X4
Operating temperature +5°C to +35°C
Storage temperature 0°C to +40°C
Relative humidity (no condensation) 10% – 70%
Dimensions (without accessories) approx.14.4 x 8.3 x 2.4 cm
Weight (without accessories) approx. 215 g
* The charging time is highly dependent on the level of sun exposure (intensity). This
can be influenced by the season, cloud cover or location. Any of these factors
can lead to longer charging times.
** When using the supplied charger cable and a USB mains adapter supplying
5V/2100mA.
Notes on the EU Declaration of Conformity
This device complies with the basic requirements and other relevant
provisions of the EMC Directive 2014/30/EU and the RoHS Directive
2011/65/EU.
The complete EU Declaration of Conformity is available from the importer and may
be requested if required (see section "Importer").

■ 16 │ GB│IE│NI SPBS 5000 B2
Kompernass Handels GmbH warranty
Dear Customer,
This appliance has a 3-year warranty valid from the date of purchase. If this product
has any faults, you, the buyer, have certain statutory rights. Your statutory rights
are not restricted in any way by the warranty described below.
Warranty conditions
The validity period of the warranty starts from the date of purchase. Please keep your
original receipt in a safe place. This document will be required as proof of purchase.
If any material or production fault occurs within three years of the date of purchase
of the product, we will either repair or replace the product for you at our discretion.
This warranty service is dependent on you presenting the defective appliance and
the proof of purchase (receipt) and a short written description of the fault and its
time of occurrence.
If the defect is covered by the warranty, your product will either be repaired or
replaced by us. The repair or replacement of a product does not signify the begin-
ning of a new warranty period.
Warranty period and statutory claims for defects
The warranty period is not prolonged by repairs effected under the warranty. This
also applies to replaced and repaired components. Any damage and defects pres-
ent at the time of purchase must be reported immediately after unpacking. Repairs
carried out after expiry of the warranty period shall be subject to a fee.
Scope of the warranty
This appliance has been manufactured in accordance with strict quality guidelines
and inspected meticulously prior to delivery.
The warranty covers material faults or production faults. The warranty does not
extend to product parts subject to normal wear and tear or fragile parts such as
switches, batteries, baking moulds or parts made of glass.

GB│IE│NI │ 17 ■
SPBS 5000 B2
The warranty does not apply if the product has been damaged, improperly used
or improperly maintained. The directions in the operating instructions for the product
regarding proper use of the product are to be strictly followed. Uses and actions
that are discouraged in the operating instructions or which are warned against
must be avoided.
This product is intended solely for private use and not for commercial purposes.
The warranty shall be deemed void in cases of misuse or improper handling, use
of force and modifications/repairs which have not been carried out by one of our
authorised Service centres.
Warranty claim procedure
To ensure quick processing of your case, please observe the following instructions:
■ Please have the till receipt and the item number (e.g. IAN 12345) available as
proof of purchase.
■ You will find the item number on the type plate, an engraving on the front page
of the instructions (bottom left), or as a sticker on the rear or bottom of the ap-
pliance.
■ If functional or other defects occur, please contact the service department listed
either by telephone or by e-mail.
■ You can return a defective product to us free of charge to the service address
that will be provided to you. Ensure that you enclose the proof of purchase (till
receipt) and information about what the defect is and when it occurred.
You can download these instructions along with many other manuals,
product videos and software on www.lidl-service.com.