Silvercrest SQWP8000 1A1 User manual

QI WIRELESS CHARGING
POWER BANK
CARGADOR INALÁMBRICO QI Y
BATERÍA DE RESPALDO
SQWP8000 1A1
IAN 306591IAN 306591
Distributed by/Distribuido por:
Lidl US LLC., Arlington, VA 22202
FCC ID: 2AJ9O-HG4127
Model No./Modelo Núm.: HG04127A-US/ HG04127B-US
Version/Versión: 08/ 2018
Made in/ Hecho en: China
QI WIRELESS CHARGING POWER BANK
Operation and Safety Notes
CARGADOR INALÁMBRICO QI Y BATERÍA DE
RESPALDO
Instrucciones de utilización y de seguridad

US-EN Operation and Safety Notes Page 3
US-ES Instrucciones de utilización y de seguridad Página 26

US-EN 3
Description of signal words .............................. Page 4
Customer service................................................... Page 4
List of pictograms used....................................... Page 5
Introduction ............................................................. Page 6
Intended use............................................................ Page 6
Trademark notices................................................ Page 6
Scope of delivery .................................................. Page 7
Important safety instructions........................... Page 7
Description of parts ............................................. Page 13
Technical data ........................................................ Page 14
Before use ................................................................ Page 15
Operation and use................................................Page 15
Charging the power bank .......................................Page 15
Checking the battery status.....................................Page 16
Qi wireless charging................................................Page 17
Charging mobile devices with the power bank......Page 18
Troubleshooting..................................................... Page 19
Cleaning and care ................................................. Page 22
Storage when not in use.................................... Page 22
Disposal..................................................................... Page 22
Three year limited warranty............................ Page 23

US-EN 4
DESCRIPTION OF SIGNAL WORDS
WARNING indicates a hazardous situation that, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation that, if not
avoided, could result in minor or moderate injury.
NOTICE indicates information considered important, but
not hazard related (e.g. messages related to property
damage).
CUSTOMER SERVICE
Call customer service at 1 [phone]
Visit the Website Customer Service Platform at
www.lidl.com/contact-us
Visit a LIDL store for further assistance.
IAN 306591 Please have your IAN number ready.

US-EN 5
LIST OF PICTOGRAMS USED
NOTE: This symbol with the signal
word “NOTE“ provides additional useful
information.
Voltage (direct current)
Watt (power)
WARNING! EXPLOSION HAZARD!
A warning with this symbol and word
“WARNING! EXPLOSION HAZARD”
indicates the potential threat of explosion.
Failure to observe this warning may result
in serious or fatal injuries and potential
property damage. Follow the instructions
in this warning to prevent serious injuries, a
danger to life or property damage!
This action sign indicates to wear suitable
protective gloves! Follow the instructions
to avoid hands striking or being struck by
objects or being in contact with thermal or
chemical materials!
“Qi“ and the Qi logo mark are trademark
of the Wireless Power Consortium (WPC)
Smart Fast Charge (SFC): Maximum
current available is used to optimize
charging time.

US-EN 6
QI WIRELESS CHARGING
POWER BANK
PIntroduction
Congratulations on your purchase. You have selected a quality
product. The instructions for use are a part of the product.
They contain important information about the safety, use and
disposal of the product. Before using the product, please learn
about all the safety information and usage instructions. Only use
the product as described and for the specified applications. If
you lend the product to someone else, please also give all the
instructions.
PIntended use
This QI WIRELESS CHARGING POWER BANK (hereinafter
referred to as “product”) is an Information Technology device
which is solely intended to be used to charge mobile devices
which have Qi wireless charging technology. Devices that do
not support Qi wireless technology can be charged through
a USB port. This product is not intended for commercial use.
Manufacturer is not liable for damages, which result from non-
intended use.
PTrademark notices
 USB®is a registered trademark of USB Implementers
Forum, Inc.
 “Qi“ and the Qi logo mark are trademark of the Wireless
Power Consortium (WPC)
 The Smart Fast Charge trademark and trade name is the
property of their respective owners.
 The SilverCrest trademark and trade name is the property of
their respective owners.
 Any other names and products may be trademarks or
registered trademarks of their respective owners.

US-EN 7
PScope of delivery
1 Qi Wireless Charging Power Bank
1 USB cable
1 Instructions for use
IMPORTANT SAFETY
INSTRUCTIONS
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS
KEEP FOR FUTURE REFERENCE. IF PASSING THIS PRODUCT
ON TO A THIRD PARTY ALSO INCLUDE ALL DOCUMENTS.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS
COULD RESULT IN DEATH OR SERIOUS INJURY.
DANGER TO LIFE AND RISK OF ACCIDENT FOR
INFANTS AND CHILDREN!
Risk of suffocation!
Never leave children unsupervised with the packaging material.
The packaging material poses a suffocation hazard. Children
frequently underestimate the dangers. The packaging material
is not a toy.
 This product is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the product by a person responsible for their safety.

US-EN 8
Children should be supervised to ensure that they do not
play with the product.
 Packaging materials are not a toy. Keep all packaging
materials out of the reach of children. Suffocation hazard!
 Never open the product casing. This product has no internal
parts requiring maintenance.
 Do not independently convert or modify the product.
 Metal objects between the charger and device to be
charged will get hot and can burn you. Remove foreign
objects from the charger before charging device.
 Repairs to the product must be performed by authorised
specialised companies or customer service. Improper repairs
may place the user in considerable danger. They will also
void the warranty.
 Do not expose the product to dripping water or splashing
water and do not place containers filled with liquids such as
vases or open drinks on top of or beside the product.
 If you use a USB power supply, the socket used must always
be easily accessible so that the USB power supply can be
quickly removed from the socket in the case of emergency.
Please also refer to the manufacturer‘s instruction manual.
 Improper handling of lithium polymer batteries can result
in fire, explosions, hazardous substances leaking, or other
dangerous situations! Do not throw the product into the fire,
as this could lead to the built-in battery exploding.
 Observe the usage restrictions and prohibitions of use
for battery-operated products in situations which may be
hazardous such as at petrol stations, airports, hospitals, etc.
 During charging process, please be noticed that the product
must not be covered. Otherwise the product can be heated.
 The product should never be charged at a PC or notebook,
because due to the high power consumption, the PC or
notebook could be damaged.

US-EN 9
 Two Qi charging devices and/or power banks must never
be placed on top of each other with the charging surface. A
device defect is the possible consequence.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS
COULD RESULT IN MINOR OR MODERATE INJURY.
 Check the product for visible external damage before use.
Do not use the product if damaged or dropped.
 Always use the product on flat and smooth surface. The
product could be damaged if it falls.
 Do not expose the product to direct sunlight or high
temperatures. It may otherwise overheat and be damaged
beyond repair.
 Do not operate the product near heat sources such as
radiators or other devices producing heat.
 Do not operate the product near open flames.
 The product is not designed for use in rooms with high
temperatures or humidity (i.e bathrooms) or those in which a
great amount of dust is generated.
 Do not expose the product to extremely high temperatures.
This applies in particular if you are thinking about storing
the product in your car. Over a prolonged period of time,
the car and the glove compartment could become extremely
hot. Remove electric and electronic devices from the car.
 Do not use the product immediately after it has brought
from a cold room to a warm room. Allow the product to
acclimatise before you switch it on.

US-EN 10
RISK OF PROPERTY DAMAGE
 Do not attach a metal object to the Qi charging surface.
 Do not charge when the Qi charging surface is covered with
a towel, layer of dust, etc.
 Do not allow the Qi charging surface to get wet from water,
beverages, etc.
 Do not use the Qi charging surface if it is malfunctioning.
 Immediately switch the product off and remove the charging
cable from the product if you smell burning or see smoke.
Have the product examined by a qualified technician before
using it again.
 Do not subject the Qi charging surface with a strong forces
or impact. Failure to do so may result in damage, injury
and/or malfunction.
 Do not place magnetic recording media inside the charging
area during charging. The magnetism generated may erase
the data on credit cards. It may also cause wristwatches and
other precision instruments to malfunction.
 During charging and immediately after charging, the Qi
charging surface and mobile device will be warm. This is
normal and not a malfunction. If there is an unusual heating,
check the Qi charging surface and mobile device.
 Always place only one mobile device to charge on the Qi
charging surface. Only one device can be charged at a
time.
 Compatibility with all Qi devices cannot be guaranteed.
 Do not attach an anti-slip mat or stickers to the Qi charging
surface. The presence of an anti-slip mat or stickers between
the mobile device to be charged and the Qi charging
surface that may prevent charging start.

US-EN 11
 If a cover or decorative accessory that does not comply
with the Qi wireless power standard has been attached to
the supported device, it may not be possible for the device
to be charged depending on the material, thickness, etc. of
the cover or accessory. In such cases, remove the attached
cover or accessory.
 If charging does not start even after the supported device
has been placed in the charging area, place the device
near the [Qi] mark in the center of the charging area.
 Before starting wireless charging, read the instructions
provided with the mobile device as well.
Changes or modifications to this product not expressly approved
by the party responsible for compliance could void the user‘s
authority to operate the product.
This product has been tested and complies with the limits for a
Class B digital device and WPC device, pursuant to Part 15 and
Part 18 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
product generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this product causes harmful
interference to radio or television reception, which can be
determined by turning the product off and on, the user is
encouraged to try and correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and receiver.
• Connect the equipment to an outlet on a different circuit than
the one the receiver is connected to.
• Consult the dealer or an experienced radio / TV technician
for help.

US-EN 12
This product complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This product may
not cause harmful interference. (2) This product must accept
any interference received, including interference that may cause
undesired operation.
The Lidl US, LLC is not responsible for interference with radios or
televisions due to unauthorised modification of the product.
The Lidl US, LLC further assumes no liability for using or
replacing cables and products not distributed by Lidl US,
LLC. The user of the product is fully responsible for correcting
interference caused by such unauthorised modification of the
product, as well as replacement of such products.
SAVE THESE INSTRUCTIONS

US-EN 13
POWER BANK
BANCO DE
ALIMENTACIÓN
SQWP8000 1A1
IAN 306591
POWER BANK
Operation and Safety Notes
BANCO DE ALIMENTACIÓN
Instrucciones de utilización y de
seguridad
5
7
8
9
10
21 3
4
6
PDescription of parts
1Micro USB input
2USB type A output
3USB type C input and output
4Qi status indicator
5On/off
button
6Battery status
indicator
7Qi charging
surface
8Powerbank
9USB cable
10 Instruction for use

US-EN 14
PTechnical data
Built-in rechargeable battery: 3.7 V , 8000 mAh,
29.6Wh (Lithium polymer)
Micro-USB input voltage / current: 5 V , 2.1 A
USB Type C input and ouput
voltage / current: 5 V , 3 A
USB Type A output
voltage / current: 5 V , 2.1 A
Qi Wireless output (1 coil)
voltage / current: 5 V , 1 A
Wireless charging power: 5 W
Wireless charging distance: ≤ 5 mm
Charging efficiency: up to 65%
Frequency bands: 110 – 205 kHz
Total maximum output power: 15 W*
Total maximal output current: 3 A*
Minimal output current: 50 mA
Operating temperature: 5 – 35 °C
Storage temperature: 0 – 45 °C
Humidity (no condensation): 10 – 70 %
Dimensions: 5.7 in x 2.83 in x 0.67 in
(145 mm x 72 mm x 17 mm)
Weight: 0.43 lbs (195 g)
*If all outputs are used at the same time, the sum of the output
current must not exceed 3 A.

US-EN 15
Notes on Qi technology:
This product with Qi wireless charging is designed to comply
with the Qi (Wireless Power Consortium) standard, but no
guarantees are given for its compatibility with all products that
comply with the standard.
PBefore use
NOTE:
Remove all packaging materials from the product. Please also
check the content of delivery inside the packaging to see if there
are any damages. If you notice any damage or missing parts,
please contact the dealer who sold this product.
POperation and use
Charging the power bank
 The built-in rechargeable battery must be fully charged
before using the product.
 To charge the power bank 8only use power supplies with
an output voltage of 5 V and an output current of at least
3 A.
The power bank must not be charged from a PC or notebook.
 Connect the USB cable 9with the Micro-USB input port
1of the power bank 8.
 Connect the other end of the USB cable 9(USB Type A) to
a USB power supply (not included in the scope of delivery)
(see fig. A).

US-EN 16
Do not connect any device to the Powerbank for charging while
the Powerbank itself is charging.
Checking the battery status
 You can check the battery status on the battery status
indicator 6of the power bank 8at anytime.
 Briefly press the ON / OFF button 5. The battery status
indicator 6shows the approximate charge status of the
internal battery in percent for approx. 30 seconds.
1 LED lights up = 25 %
2 LEDs lights up = 50 %
3 LEDs lights up = 75 %
4 LEDs lights up = 100 %
A9

US-EN 17
Qi wireless charging
 Put your Qi compatible device to be charged on the centre of
the Qi charging surface 7of the power bank 8.
 Charging starts automatically when the Powerbank is
switched on. When Qi charging is active, Qi status indicator
4lights green.
 Slightly adjust the charging position of the device to be
charged so that its charging surface is facing down to the
centre of the Qi charging surface 7of the power bank 8.
 If wireless charging does not start, move your device to be
charged more accurately to the centre of the Qi charging
surface 7.
 While in idle status (standby mode), the Qi charging surface
4will illuminate amber in colour.
 When the charging process has finished the Qi Wireless
charger indicator 4will still illuminate green in colour*.
 The Qi status indicator 4also shows quick flashing when
the power bank cannot detect any Qi charging device on
the Qi charging surface 7. In this case, move your Qi
compatible device to be charged towards the center of Qi
charging surface 7in order to start wireless charging.
*NOTE:
1) Qi status indicator 4may change back to amber colour
(standby mode) when wireless charging has finished if the
mobile device closed the wireless communication between
the Qi charging surface 7and the mobile device.
2) All devices to be charged must be comply with Qi Standard.

US-EN 18
Charging mobile devices with the power
bank
You can charge up to three devices at the same time using the
power bank 8. If all outputs are used at the same time, the
sum of the output current must not exceed 3 A.
 Connect the USB cable 9or the original charging cable
of the device to be charged to the USB output 2. Then
connect Micro-USB port of the USB Cable 9to the Micro-
USB input of device to be charged. The charging process
will start automatically.
 If your mobile device has a USB type C input, you can use a
type C to type C connection cable (not included) to connect
your device’s type C input to this power bank’s USB Type C
output 3. The charging process will start automatically.
 At the same time, you can place the device to be charged
on the Qi charging surface 7.
 In case if the charging process does not begin immediately,
press the ON / OFF button 5briefly to begin the charging
process. The current battery status of the power bank 8is
displayed during the charging process by the battery status
indicator 6.
 To end the charging process, disconnect the USB charging
cable from the mobile device and the power bank 8. The
power bank will switch OFF and battery status indicator 6
will switch off after approx. 30 seconds.
 Or simply double click the ON / OFF button 5. The power
bank 8will switch off.

US-EN 19
NOTE:
If you use both USB ports, a voltage of 5 V will be output at both
outputs. The maximum output current must not exceed
3 A for both outputs.
PTroubleshooting
= Problem
= Cause
= Solution
It may not be possible to charge a Qi compatible
device.
The mobile device is already fully charged.
Take away the fully charged device for use, until its internal
battery was drained again. Then put device back to Qi
charging surface 7for charging.
The mobile device has become very hot as a result of
charging.
Remove the mobile device from the wireless charging surface
7for a few hours to let it cool down, and also check if your
product was damaged.
This product is in a location where strong radio waves or
noise is being generated, such as TV towers, electric power
plants, or gas stations.
Under this environment, use other output port, such as USB
Type C or Type A port for charging up your mobile device.

US-EN 20
The power bank 8is not being charged.
It may be that the power bank is not connected properly.
Check that it is connected.
In order to charge the power bank, a power supply with 5 V
and at least 3 A has to be used.
A connected device is not being charged.
The battery is drained.
Charge the battery.
The device is not connected.
The device is not connected. Check that it is connected.
Briefly press the ON / OFF button 5to begin the charging
process.
The current consumption of the connected device might be
too low.
Check with your connected device manual and see if your
connected device current consumption comply with this
product. The minimal output current of the power bank is
approx. 50 mA.
The power bank 8does not react when the
button is pressed or when a device is connected,
even though the battery is charged.
The power consumption of the connected devices is too high.
Therefore, the internal overcurrent protection device was
activated.
Reduce the number of devices connected and press the ON
/ OFF button 5.