Silvercrest SFW 100 C4 Instruction Manual

FOOT WARMER SFW 100 C4
IAN 303828
FOOT WARMER
Operating instructions and safety advice

GB / IE / NI Operating instructions and safety advice Page 5
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the
device.

1
2 3

5GB/IE/NI
Table of contents
List of pictograms used........................................................................................................Page 6
Introduction...................................................................................................................................Page 6
Proper use............................................................................................................................................Page 6
Description of parts.............................................................................................................................Page 7
Included items .....................................................................................................................................Page 7
Technical data.....................................................................................................................................Page 7
Important safety instructions.........................................................................................Page 7
Safety system..............................................................................................................................Page 9
Preparing the product for use.......................................................................................Page 9
Switching on / off / Selecting the temperature...................................................................................Page 9
Temperature levels ..............................................................................................................................Page 10
Automatic switch-off ............................................................................................................................Page 10
Cleaning and care....................................................................................................................Page 10
Storage .............................................................................................................................................Page 11
Disposal............................................................................................................................................Page 11
Warranty / Service centre .................................................................................................Page 11
Declaration of Conformity................................................................................................Page 12

6 GB/IE/NI
Introduction / Important safety instructionsIntroduction
Foot Warmer
Introduction
Please make yourself familiar with the
foot warmer before preparing it for use
or using it for the first time. Please read
the following operating instructions and the impor-
tant safety instructions carefully. Always use the foot
warmer only as described and for the stated areas
of use. Keep these instructions in a safe place. If you
pass the foot warmer on to anyone else, please en-
sure that you also pass on all the documentation.
Proper use
This foot warmer is intended for applying heat to
the human body. Do not use the foot warmer wear-
ing shoes, as this would reduce your sensitivity to
heat and also soil the foot warmer. This foot warmer
is not intended for use in hospitals or for commercial
use. In particular it must not be used for babies or
infants, persons who are insensitive to heat, helpless
persons, or animals. Any use other than that de scribed
here or modification to the foot warmer is not per-
mitted and could lead to injury and / or damage to
the product. The manufacturer accepts no liability
for any damage caused by improper use.
List of pictograms used
Read the instructions! Caution – electric shock!
Danger to life!
Volt (AC) AUTO STOP Automatic switch-off
Hz Hertz (mains frequency) Quick heat-
up time
"Turbo" rapid heating function
WWatts (effective power) Do not wash.
Safety class II Hand washing
Observe caution and safety notes! Do not use bleach.
Not suitable for very small children
age 0–3 years! Do not dry in a tumbler dryer.
Do not insert pins! Do not iron.
Do not use folded or rucked! Do not dry-clean.
06.0.43510 HOHENSTEIN HTTI
The textiles used in this foot warmer
meet the strict human ecological re-
quirements of Oeko-Tex Standard 100,
as verified by the German Hohenstein
Research Institute.
b
a
Dispose of the packaging and the
foot warmer in an environmentally
friendly manner!

7GB/IE/NI
Introduction / Important safety instructionsIntroduction
Important safety
instructions
Failure to
comply with the following instruc-
tions can cause personal injury or
material damage (electric shock,
skin burns, fire). The following ad-
vice on safety and hazards is in-
tended to protect your health and
that of other people as well as to
protect the foot warmer. Please
observe these safety instructions
and make sure that you pass on
this manual together with the foot
warmer.
SCALDING HAZARD!
This foot warmer may
not be used by persons insensi-
tive to heat and other persons
in need of protection who do not
respond to overheating (e.g. dia-
betics, persons with skin changes
caused by illness or scarred skin
Description of parts
1Teddy lining, removable
2Control unit
3Function indicator
Included items
Immediately after unpacking, check that all the
items are present and that the product is in perfect
condition.
1 Foot warmer with removable teddy lining and
control unit
1 Set of operating instructions
Technical data
Model: SFW 100 C4
Type: FW 10 S
Power supply:
220–240 V / 50–60 Hz
Power input: 100 W
Dimensions: approx. 26 x 26 x 30 cm
(W x H x D)
Protection class: II /
Protection class
(water protection): Foot warmer: IP X1,
drip-resistant
Control unit: IP X0, no
moisture protection
Electric field strength: max. 5000 V / m
Magnetic field strength: max. 80 A / m
Magnetic flux density: max. 0.1 milli-Tesla
Material:
Surface of foot warmer: 100 % polyester
Teddy lining: 100 % polyester
Manufacturer:
MGG Elektro GmbH
Steinstraße 27
DE-40210 Düsseldorf
GERMANY
IMPORTANT INSTRUCTIONS –
KEEP FOR FUTURE REFERENCE!

8 GB/IE/NI
Important safety instructions / Safety system / Preparing the product for useImportant safety instructions
areas in the application area,
after using analgesics or alcohol).
There is a risk of receiving skin
burns.
This
foot warmer may not be
used for very young children
(0–3 years), as they are unable
to react to overheating. There is
a risk of skin burns.
This foot warmer may not be used
by young children (3–8 years)
unless the control unit was set by
a parent or a supervising person
and the child was adequately
instructed on the safe use of the
foot warmer. There otherwise is
a risk of burns.
This foot warmer may be used
by older children age 8 and up
and persons with diminished
physical, sensory or mental ca-
pacities or lacking experience
and knowledge when super-
vised and instructed on the safe
use of the foot warmer and un-
derstand the associated risks.
Children must be supervised to
prevent them from playing with
the foot warmer. There is a risk
of injury.
Children must not perform clean
or maintain the product without
supervision. There is a risk of in-
jury.
This foot warmer is not intended
for use in hospitals or for com-
mercial use. This poses a risk of
injuries and/or damage to the
foot warmer.
Do not use this foot warmer to
warm up animals.
Do not use this foot warmer with
shoes to prevent soiling.
Do
not poke needles or
other pointy objects into the foot
warmer. There is a risk of electric
shock.
Do
not switch on the foot
warmer whilst folded or bunched
up. The foot warmer may other-
wise be damaged.
Do not use when wet! Other-
wise there is a risk of electric
shock.
Under certain circumstances, the
electrical and magnetic fields
emitted from the foot warmer
could interfere with the proper
functioning of your heart pace-
maker. However, the levels are
far below the permissible limits:
electric field strength: max.
5000 V / m, magnetic field
strength: max. 80A / m, magnetic

9GB/IE/NI
Important safety instructions / Safety system / Preparing the product for use
flux density: max. 0.1 milli-Tesla.
Ask your doctor and, if relevant,
the manufacturer of your heart
pacemaker before you use this
foot warmer.
Do not pull, twist or kink the
cables. The foot warmer may
otherwise be damaged.
Regularly check the foot warmer
for signs of wear or damage. If
signs thereof are detected, the
foot warmer was used improp-
erly or will no longer heat up, it
must first be inspected by the
manufacturer before being
switched on again.
If the mains power cable of this
foot warmer is damaged, it must
be replaced by the manufacturer
or its service department, or a
similarly qualified person, to pre-
vent hazards.
The electronic components in-
side the control unit will heat up
whilst operating the foot
warmer. For this reason, the con-
trol unit may not be covered or
be lying on the foot warmer dur-
ing operation. This poses a risk
of injuries and/or damage to
the foot warmer.
Always observe the information
on start-up, cleaning and care,
and storage.
If you have additional questions
on using our products, please
contact our Customer Service
Department.
Safety system
Note: This foot warmer is equipped with a safety
system. The electronic sensor technology prevents
the entire surface of the foot warmer from overheat-
ing by automatically switching off in the event of a
fault. If the safety system switches the foot warmer
off automatically due to a fault, then the function
display 3on the control unit 2is no longer illu-
minated, even if the foot warmer is switched on.
Please note that, for safety reasons, the foot
warmer must not be used after a fault and must
be returned to the service address indicated.
Preparing the product for use
Note: When the foot warmer is used for the first
time, you may notice a smell of plastic; however,
this will disappear after a short time.
Switching on / off / Selecting
the temperature
Insert the mains plug into the mains socket.
Switching on:
Set level 1, 2, 3, 4, 5 or 6 on the control
unit 2to switch the foot warmer on.
Note: The function display 3illuminates
after the foot warmer is switched on.
Note: This foot warmer features rapid heating,
which allows it to heat up within the first 15
minutes of operation.
Switching off:
Set level 0 on the control unit 2to switch the
foot warmer off.
Important safety instructions

10 GB/IE/NI
Cleaning and care / Storage / Disposal / Warranty / Service centrePreparing the product for use / Cleaning and care
Note: The function display 3ceases to illu-
minate.
Selecting the temperature:
Just before using the foot warmer, set it to the
highest temperature setting (setting 6). This will
cause the foot warmer to warm up quickly.
The foot warmer can of course be used at any
time if it is switched off. Its teddy plush lining
will warm your feet even if an electric socket is
nowhere near.
When operat-
ing the foot warmer for several ho urs,
we recommend setting the control
unit 2to the lowest temperature set-
ting to prevent overheating of the feet
and subsequent potential skin burns.
Temperature levels
Set the required temperature level on the
control unit 2.
Level 0: off
Level 1: minimum heat
Level 2–5: customised heat
Level 6: maximum heat
Automatic switch-off
Note: The foot warmer switches itself off automati-
cally after about 90 minutes. The function display 3
then starts to flash.
Then select the setting 0 and after about
5 seconds, reset the foot warmer to the desired
temperature setting to switch it on again.
Note:
Switch the foot warmer off (setting 0) and pull the
mains plug out of the mains socket if the foot warmer
is not to be used after it has switched off automati-
cally.
Cleaning and care
DANGER TO
LIFE BY ELECTRIC SHOCK! Al-
ways remove the power plug from
the socket before cleaning the foot warmer.
Otherwise there is a risk of electric shock.
Use a dry, lint-free cloth for control unit 2
cleaning and care.
RISK OF DAMAGE TO THE
PRODUCT OR PROPERTY!
Never immerse the control unit 2
in water or other liquids. It may otherwise be
damaged.
Use a damp cloth and if necessary a little mild
detergent to clean small stains on the foot
warmer.
RISK OF DAMAGE TO THE
PRODUCT OR PROPERTY! Do
not use chemical cleaning or scour-
ing agents to clean the foot warmer and con-
trol 2. The foot warmer and control unit 2
may otherwise be damaged.
RISK OF DAMAGE TO THE
PRODUCT OR PROPERTY!
Please note that the foot warmer
must not be washed in a machine, dry-cleaned,
wrung out, tumble-dried, mangled or ironed.
The foot warmer may otherwise be damaged.
Do not wash.
Do not bleach. Do not use any
cleaning agents containing bleach
(such as heavy duty detergents).
Do not dry in a tumbler dryer.
Do not iron.
Do not dry-clean.
The removable teddy lining 1can
be washed by hand. Use a mild

11GB/IE/NI
Cleaning and care / Storage / Disposal / Warranty / Service centre
laundry detergent according to the manufactur-
er’s instructions.
DANGER OF ELECTRIC
SHOCK! RISK OF PROPERTY
DAMAGE! Never switch on the
foot warmer to dry. Otherwise there is a risk of
electric shock.
DANGER OF ELECTRIC
SHOCK! Only resume using the
foot warmer when the foot warmer
and the removable fleece insert 1are fully
dry. Otherwise there is a risk of electric shock.
Storage
RISK OF DAMAGE TO THE
PRODUCT OR PROPERTY! Let
the foot warmer cool before putting
it away. The foot warmer may otherwise be
damaged.
RISK OF DAMAGE TO THE
PRODUCT OR PROPERTY! Do
not crease the foot warmer by plac-
ing items on top of it during storage. Otherwise
material damage could occur.
If you do not intend to use the foot warmer for
any length of time, store it in the original pack-
aging in a dry environment and without weigh-
ing it down.
Disposal
The packaging is made entirely of recyclable mate-
rials, which you may dispose of at local recycling
facilities.
b
a
Observe the marking of the packaging
materials for waste separation, which
are marked with abbreviations (a) and
numbers (b) with following meaning:
1–7: plastics / 20–22: paper and fibre-
board / 80–98: composite materials.
Contact your local refuse disposal au-
thority for more details of how to dispose
of your worn-out product.
To help protect the environment, please
dispose of the product properly when it
has reached the end of its useful life and
not in the household waste. Information
on collection points and their opening
hours can be obtained from your local
authority.
Warranty / Service centre
We provide a 3-year warranty from the date of
purchase for defects in material and manufacture
of the foot warmer.
The warranty does not cover:
· Damage from improper use.
· Wear parts.
· Damage caused by the customer.
·
If the device has been opened by an unauthoris ed
repair shop.
This warranty does not affect the customer‘s legal
rights. The customer must provide proof of purchase
in order for any warranty claims within the warranty
period to be honoured. Warranty claims must be
filed with MGG Elektro GmbH, Düsseldorf, Germany
within 3 years from the date of purchase.
In the event of a claim, please contact
our Service Department listed below:
Service Hotline (toll-free):
0800 93 10 319
(Mon–Fri: 8 am–6 pm)
ser[email protected]
1800 93 92 35
(Mon–Fri: 8 am–6 pm)
ser[email protected]
Preparing the product for use / Cleaning and care

12 GB/IE/NI
Warranty / Service centre / Declaration of Conformity
If we ask you to return the defective foot warmer,
please send it to the following address:
NU Service GmbH
Lessingstraße 10 b
DE-89231 Neu-Ulm
GERMANY
IAN 303828
Declaration of Conformity
This foot warmer complies with the requirements of
the relevant European and national guidelines.
This is confirmed by the CE mark.
The relevant declarations are held by the manufac-
turer.

NU Service GmbH
Lessingstraße 10 b
DE-89231 Neu-Ulm
GERMANY
Last Information Update: 05 / 2018
Ident.-No.: 749.283_SFW 100 C4_2018-03-22_01_IM_Lidl_LB6a_GB-IE-NI
IAN 303828