Silvercrest SFW 350 C2 User manual

MINCER SFW 350 C2
IAN 285532
MINCER
Operating instructions
ΚΡΕΑΤΟΜΗΧΑΝΗ
Οδηүίες χρήσης
FLEISCHWOLF
Bedienungsanleitung

GB/IE/NI/CY Operating instructions Page 1
GR/CY Οδηүίες χρήσης Σελίδα 23
DE/AT/CH Bedienungsanleitung Seite 45
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.
Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τις δυο σελίδες με τις εικόνες και εξοικειωθείτε με όλες τις
λειτουργίες της συσκευής.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.

A
B
.!-
3
6
0
1




C+

,
%




SFW 350 C2 GB│IE│NI│CY │ 1 ■
Index
Introduction...................................................2
Copyright .............................................................. 2
Limited liability ........................................................... 2
Intended use ..................................................2
Items supplied/Component description ............................3
Technical data .................................................4
Safety instructions .............................................4
Assembly/Disassembly .........................................6
Assembling the meat grinder ................................................ 6
Assembling the sausage stuffer attachment .................................... 7
Assembling the kibbeh attachment ........................................... 8
Assembling the biscuit attachments ........................................... 8
Fitting the strainer attachment ............................................... 9
Operation ...................................................10
Operating the appliance ..................................................10
Processing meat.........................................................11
Processing sausage meat.................................................. 12
Using the kibbeh attachment ............................................... 12
Making biscuits .........................................................13
Straining tomatoes....................................................... 13
Non-functionality .............................................14
Cleaning.....................................................14
Cleaning the motor block .................................................15
Cleaning the accessories.................................................. 15
Storage .....................................................16
Disposal .....................................................16
Kompernass Handels GmbH warranty............................16
Service................................................................18
Importer ............................................................... 18
Recipes......................................................19
Kibbeh ................................................................19
Meat rolls..............................................................20
Fresh Grill Sausages .....................................................21
Biscuits ................................................................21

SFW 350 C2
■ 2 │ GB│IE│NI│CY
Introduction
Congratulations on the purchase of your new appliance.
You have clearly decided in favour of a quality product. These operating instruc-
tions are a part of this product. They contain important information in regard to
safety, use and disposal. Before using the product, familiarise yourself with all of
these operating and safety instructions. Use the product only as described and
only for the specified areas of application. Retain these instructions for future
reference. In addition, pass these documents on, together with the product, to
any future owner.
Copyright
This documentation is copyright protected.
Any copying or reproduction of it, including as extracts, as well as the reproduc-
tion of images, also in an altered state, is only permitted with the written authori-
sation of the manufacturer.
Limited liability
All technical information, data and instructions for the installation, connection
and operation contained in these operating instructions correspond to the latest
available at the time of printing and, to the best of our knowledge, take into
account our previous experience and know-how.
No claims can be derived from the details, illustrations and descriptions in these
instructions.
The manufacturer assumes no responsibility for damage caused by failure to ob-
serve these instructions, improper use, incompetent repairs, making unauthorised
modifications or for using unapproved replacement parts.
Intended use
This appliance is intended only for the preparation of food in quantities expected
in domestic households:
▯ Mincing fresh meat,
▯ Making sausages with natural or artificial sausage skin,
▯ Making biscuits,
▯ Straining tomatoes.
This appliance is not intended for the processing of frozen foods or other hard
foodstuffs, e.g. bones or nuts, or for use in commercial or industrial environments.

SFW 350 C2 GB│IE│NI│CY │ 3 ■
Items supplied/Component description
Figure A:
Biscuit attachment with pattern strips
Stodger
Feeding tray
Motor unit
Meat grinder casing made of metal
Locking clamp
Tomato outlet
Plastic screw
Strainer sieve
Transport screw
-Spring
3Cross blade
!Medium-sized, fine perforated disc
.Ring clamp
0Sausage stuffer attachment
6Coarse perforated disc
1Kibbeh attachment
Figure B:
%Locking button
Figure C:
+“I” button (on)
,“0” button (off)
“<” button (reverse mode)

SFW 350 C2
■ 4 │ GB│IE│NI│CY
Technical data
Voltage 220 - 240 V ∼, 50Hz
Power consumption 250 - 350 W
Protection class II /
All of the parts of this appliance
that come into contact with food are
food-safe.
C.O. Time 15 minutes
C.O. Time
The C.O. Time (Continuous Operation) details how long an appliance may be
used without the motor overheating and being damaged. After the appliance
has run for this period it must be switched off until the motor has cooled itself
down.
Safety instructions
RISK OF ELECTRIC SHOCK
► Ensure that the power cable does not become damaged.
Protect the cable from heat and ensure that it cannot be
trapped or clamped.
► Arrange for damaged power cables and/or plugs to be
replaced as soon as possible by a qualified specialist or by
Customer Services.
► Use the appliance only in dry indoor areas, not outdoors.
Never immerse the motor block in water or any other
liquid! If you do, then you could receive a potentially
fatal electric shock.
WARNING!
► Never use the appliance for purposes other than those listed
here. There will be a major risk of serious accidents should
you try to neutralise the safety fitments on the appliance!

SFW 350 C2 GB│IE│NI│CY │ 5 ■
WARNING! RISK OF INJURY!
► Never put your hand into the openings of the appliance. Do
not insert any objects of any kind into the openings – except
for the appropriate stodger and the foodstuff to be pro-
cessed. If you do, there will be a serious risk of accidents!
► Unplug the appliance from the power source before attaching
or removing accessories.
► Do not leave the appliance unsupervised when it is ready
for use. To avoid it being switched on accidentally, always
unplug the appliance after use or during breaks.
► Only use the original accessory parts for this appliance.
Other accessories may not meet the safety requirements.
► Never operate the appliance in a no-load condition. This
could irreparably damage the appliance.
► Before changing accessories or additional parts that are in
motion during operation, the appliance must be switched off
and disconnected from mains power.
► Never use the appliance for purposes other than those
described in these instructions.
► Warning: the cross blade is very sharp! Always take care
when handling and cleaning the appliance.
► The appliance should always be disconnected from the
mains when unattended and before assembly, disassembly
or cleaning.
► This appliance may not be used by children.
► The appliance and its connecting cable must be kept away
from children.

SFW 350 C2
■ 6 │ GB│IE│NI│CY
WARNING! RISK OF INJURY!
► This appliance may be used by persons with limited physi-
cal, sensory or mental capabilities or lack of experience
and knowledge, provided that they are under supervision
or have been told how to use the appliance safely and are
aware of the potential risks.
► The appliance must not be used as a plaything by children.
Assembly/Disassembly
CAUTION - PROPERTY DAMAGE!
► All accessories are coated with a thin film of oil to protect them from corro-
sion. Therefore, carefully clean all of the parts before using the appliance
for the first time, as described in detail in the chapter “Cleaning”. After
subsequent usage, always apply a light coating of cooking oil to the metal-
lic components.
NOTICE
► Before using for the first time, remove the protective foil from the control panel.
Assembling the meat grinder
Unfold the fold-out side. There you will find the step-by-step illustrations for as-
sembling the appliance.
1) Place the transport screw in the meat grinder casing .
2) Place the spring -onto the transport screw .
3) Then fit the cross blade 3on so that the sharp side points away from the
spring -. Ensure that the square opening in the cross blade 3is placed
correctly on the square axle.

SFW 350 C2 GB│IE│NI│CY │ 7 ■
WARNING! RISK OF INJURY!
► The cross blade 3is very sharp! Risk of injury!
CAUTION - PROPERTY DAMAGE!
► The appliance will be damaged if the cross blade 3is inserted the other
way around!
4) Select the required perforated disc !/6.
5) Place your selected cutting disc !/6into the meat grinder casing so
that the fixings on the cutting disc !/6are located in the openings in the
meat grinder casing .
6) After everything has been correctly assembled, screw the ring clamp .
back on hand-tight.
7) The ready-assembled meat grinder casing is connected by a bayonet
connector to the motor unit :
– Insert the meat grinder casing into the motor unit such that the
arrow on the meat grinder casing lies against the symbol on the
motor unit . The locking button %presses itself in (Fig. B).
– Lightly press the meat grinder casing in and at the same time turn
the feeding shaft on the meat grinder casing into the middle position
(Fig. B) so that the arrow on the feeding shaft points to the symbol .
When the meat grinder casing engages, the locking button %
springs out.
– Finally, place the feeding tray on top of the feeding funnel.
– To dismantle it, press the locking button %and turn the feeding funnel
to the right (Fig. B) . You can now pull the meat grinder casing out.
Assembling the sausage stuffer attachment
Unfold the fold-out side - there you will find the step-by-step illustrations for as-
sembling the appliance.
1) Remove the meat grinder casing as described under “Assembling the
meat grinder”.
2) Dismantle all parts which are fitted to/in the meat grinder casing and
clean them.
3) Coat all metal parts with cooking oil.
4) Put the transport screw , the spring -and the cross blade 3back into
the meat grinder casing .
5) Insert the coarse perforated disc 6so that the fixings on the disc 6are
inside the recesses on the mincer attachment .
6) Then place the sausage filling attachment 0in front of the coarse perforated
disc 6.

SFW 350 C2
■ 8 │ GB│IE│NI│CY
7) Screw the ring clamp .on hand-tight.
8) Assemble the meat grinder casing as described under “Assembling the
meat grinder”.
Assembling the kibbeh attachment
Unfold the fold-out side. There you will find the step-by-step illustrations for as-
sembling the appliance.
1) Remove the meat grinder casing as described under “Assembling the
meat grinder”.
2) Disassemble any attachments that might be fitted and clean the meat grinder
casing .
NOTICE
► For the kibbeh attachment 1, the cross blade 3with the spring -is not
required! If need be, remove them both from the meat grinder casing .
The transport screw remains inside the mincer attachment .
3) Coat all metal parts with cooking oil.
4) If not already done, place the transport screw inside the mincer attach-
ment .
5) Insert the two plastic parts of the kibbeh attachment 1so that the fixings
on the bottom kibbeh attachment 1ring are located in the openings in the
meat grinder casing .
6) When everything has been attached correctly, screw the ring clamp .back
on hand-tight.
7) Assemble the meat grinder casing as described under “Assembling the
meat grinder”.
Assembling the biscuit attachments
Unfold the fold-out side. There you will find the step-by-step illustrations for as-
sembling the appliance.
1) Remove the meat grinder casing as described under “Assembling the
meat grinder”.
2) Disassemble any attachments that might be fitted and clean the meat grinder
casing .
NOTICE
► For the biscuit attachment , the cross blade 3with the spring -is not
required! If need be, remove them both from the meat grinder casing .
The transport screw remains inside the mincer attachment .
3) Coat all metal parts with cooking oil.
4) If not already done, place the transport screw inside the mincer attach-
ment .

SFW 350 C2 GB│IE│NI│CY │ 9 ■
5) Pull the pattern strips away from the front of the biscuit attachment .
6) First place the plastic disc and then the metal disc of the biscuit attachment
into the meat grinder casing (see fold-out side). Insert the biscuit at-
tachment . so that the fixings on the biscuit attachment . are located in
the openings in the meat grinder casing .
7) After everything has been correctly assembled, screw the ring clamp .
back on hand-tight.
8) Replace the pattern strips back in to the front of the biscuit attachment .
Ensure that the grip on the pattern strips points away from the appliance.
If it does not, you will not be able to adjust the pattern, which is located
directly on the grip.
9) Assemble the meat grinder casing as described under “Assembling the
meat grinder”.
10) To dismantle it, you must first remove the pattern strips before you can
screw the ring clamp .open and take the biscuit attachment back out.
Fitting the strainer attachment
Unfold the fold-out page – it contains the step-by-step illustrations for assembling
the appliance. The figure displayed under point 8) will help you assemble the
appliance.
1) Remove the meat grinder casing as described in “Assembling the meat
grinder”.
2) Remove any attachments that might be fitted and clean the meat grinder
casing .
NOTICE
► The transport screw and the cross blade 3with the spring -are not
required for the strainer attachment! Remove these from the meat grinder
casing if necessary.
3) Push the plastic screw into the meat grinder casing .
4) Push the strainer sieve over the plastic screw so that the tabs on the
strainer sieve fit into the recesses in the meat grinder casing . The holes
of the strainer sieve should be facing downwards.
5) Once everything has been correctly attached, roll the ring clamp .over the
strainer sieve and screw it on hand-tight.
6) Fit the meat grinder casing as described in “Assembling the meat
grinder”.
7) Undo the locking clamp on the tomato outlet .
8) Place the tomato outlet under the strainer sieve by pushing the tip of the
strainer sieve through the small hole in the tomato outlet :

SFW 350 C2
■ 10 │ GB│IE│NI│CY
9) Fasten the locking clamp so that it grips the meat grinder casing .
Operation
RISK OF ELECTRIC SHOCK
► NEVER open the housing of the motor unit – it does not contain any
user-serviceable elements. If the housing is opened, the warranty becomes
void. If the housing is opened, there is a risk of receiving a potentially fatal
electric shock.
CAUTION - PROPERTY DAMAGE!
► Do not use the appliance for longer than 15 minutes continuously. To avoid
an overheating of the appliance, after such a period switch it off and allow
it to cool down for ca. 30 minutes.
► NEVER activate the buttons “I” +or “<” , during a change of rotation
direction, if the appliance motor has not come to a complete stop. This
could damage the motor.
Operating the appliance
Once the appropriate attachments have been fixed:
1) Place the appliance where it will at all times be absolutely stable and under
no circumstances could it fall off of the work surface or in any way come into
contact with water (due to vibrations or becoming snagged in the power
cable). Vibration is unavoidable when it is working.

SFW 350 C2 GB│IE│NI│CY │ 11 ■
RISK OF ELECTRIC SHOCK
► Never touch an appliance, which is plugged in or is operational when it
happens, that falls or lands in water – or in the case of other emergencies!
First disconnect the appliance from the mains power source in all emergen-
cy situations! Otherwise you run the risk of serious injury or loss of life!
2) Put the food which is to be processed in the feeding tray and place a
catchment container at the front under the exit opening.
3) First press the button “0” ,to check that the appliance is still switched off.
Otherwise there is a risk that the appliance could unintentionally start
when the plug is inserted into the power socket.
4) Then insert the plug into a mains power socket.
5) Press the button “I” +to start the appliance.
WARNING! RISK OF INJURY!
► Push the foodstuff into the feeding shaft ONLY with the round stodger –
NEVER with one’s fingers, forks, spoons or similar objects. That could lead
to physical injury and also damage the appliance.
CAUTION - PROPERTY DAMAGE!
► Do not ever press so hard that the motor gets audibly slower. This could
overburden the machine and damage it.
Processing meat
1) Use pieces of meat that fit easily into the feeding funnel. If necessary, cut the
meat to size beforehand. Check that the meat does not have any bones and
or tendons.
WARNING!
► Minced meat is very prone to bacterial contamination. Therefore take care
to maintain good hygiene when processing meat. If you do not, it may
cause serious health problems.
2) When you have read and understood all of the instructions on the topic
”Meat“, you can now use the appliance as described in the chapter
“Operating the appliance”.

SFW 350 C2
■ 12 │ GB│IE│NI│CY
Processing sausage meat
1) Pass meat through the meat grinder twice before using it as sausage stuffing.
2) To make sausage stuffing, add some chopped onions, spices and other
ingredients to the minced meat, as per your recipe, and knead the mixture
well. Refrigerate this for 30 minutes before processing it further.
3) Pull one end of the sausage skin (natural or artificial sausage skin) onto the
sausage stuffer attachment 0and tie a knot in the other end. For 1 kg of the
filling, you will need approximately 1.60 m of sausage skin.
TIP!
Soak the natural sausage skin in lukewarm water for about 3 hours before
using it and wring it out before attaching it. This will make the natural sau-
sage skin more elastic. Natural sausage skins are available from butcher
suppliers close to slaughter houses or from your family butcher.
4) The sausage mixture will be pressed into the sausage skin by the sausage
stuffer attachment 0. When it is long enough switch the appliance off, press
the sausage together at the ends and rotate it a couple of times along its
longitudinal axis.
TIP!
Sausage meat tends to expand when cooked or frozen. Therefore, to prevent
it from bursting it is best not to overstuff the sausage.
5) When you have read and understood all of the instructions on the topic
”Sausage”, you can now use the appliance as described in the chapter
“Operating the appliance”.
Using the kibbeh attachment
With the kibbeh attachment 1foodstuffs can be processed to form hollow rolls
of meat or vegetables, which can then be stuffed as desired.
1) First put the meat through the meat grinder twice before pressing it through
the kibbeh attachment 1.
2) When you have read and understood all of the instructions on the topic
“kibbeh-attachment”, you can now use the appliance as described in the
chapter “Operating the appliance”.

SFW 350 C2 GB│IE│NI│CY │ 13 ■
Making biscuits
After you have made the biscuit pastry according to your recipe, and after hav-
ing fixed the biscuit attachment :
1) Line a small baking tray with greaseproof paper and place or hold it directly
under the exit opening at the front of the appliance.
2) Press pastry evenly into the meat grinder casing – the transport screw 
then pushes it through the selected design on the design motif strip of the
biscuit attachment .
3) When the biscuit is the required length, stop the appliance and break the
pastry off at the exit opening. Lay the biscuits on the baking tray.
4) When you have read and understood all of the instructions on the topic
“Biscuits”, you can now use the appliance as described in the chapter
“Operating the appliance”.
Straining tomatoes
1) Place a container under the tomato outlet .
2) Place a container at the front under the strainer sieve .
3) Quarter the tomatoes and push them slowly and evenly into the meat grinder
casing .
The plastic screw pushes the tomatoes through the strainer attachment.
The strained tomatoes fall in the tomato outlet . The tomato skin is ejected
at the front from the strainer sieve .
NOTICE
If tomato juice starts leaking from the screw joints of the strainer attachment,
this can have the following causes:
–You are working too fast.
–You are using too much pressure to press the tomato pieces into the
appliance.
–The tomato pieces are too large.
► Try working more slowly; press the tomato pieces gently into the appliance
and cut the tomatoes into smaller pieces.
4) Once you have read and understood all of the instructions in the section
“Straining tomatoes”, you can use the appliance as described in the section
“Operating the appliance”.

SFW 350 C2
■ 14 │ GB│IE│NI│CY
Non-functionality
If the drive is blocked by accumulated food:
■ Press the button “0” ,to stop the meat grinder.
■ Press and hold the button “<” . The appliance will now run in the reverse
direction. This enables you to transport the food which has become stuck a
short way backwards, and the motor to run freely again.
■ When the drive runs smoothly again, release the “<” button.
■ Press the button “I” +to re-start the meat grinder.
■ If you do not succeed in getting the drive free with this, clean the appliance
as described in the chapter “Cleaning”.
Should the motor suddenly stop, it could be due to automat-
ic activation of the internal overload fuse. This is intended to
protect the motor.
■ Switch the appliance off and allow it cool down for approximately 30 min-
utes before continuing to use it.
■ Should this not work, wait for a further 15 minutes.
■ If it still does not function at the end of this period, this indicates a technical
problem. In this case, contact the Customer Service Centre.
If the power cable is damaged or the accessories are
visibly damaged:
■ Immediately switch the appliance off by pressing the “0” ,button!
■ If this is not possible without risk to personal safety, disconnect the plug from
the mains power socket.
■ Arrange for the defective parts to be repaired by Customer Services before
re-using the appliance.
Cleaning
RISK OF ELECTRIC SHOCK
► Disconnect the plug from the mains power socket before cleaning the appli-
ance. In this way accidents caused by the inadvertent switching on of the
appliance and electric shocks can be avoided.

SFW 350 C2 GB│IE│NI│CY │ 15 ■
Cleaning the motor block
■ Clean the exterior surfaces and the power cable with a slightly damp cloth.
Dry the appliance well before re-using it.
RISK OF ELECTRIC SHOCK
► Never immerse the motor block in water or any other liquid! Should this
occur, you are at risk of a potentially fatal electric shock if permeating
moisture makes contact with the electrical wiring.
CAUTION - PROPERTY DAMAGE!
► Never use detergents, abrasive cleaners or solvents. These could damage
the appliance and leave residues on the foodstuffs.
Cleaning the accessories
NOTICE
► Do not clean any metal components in the dishwasher! This can damage
the components!
■ Metal components in contact with food should be cleaned ...
– by hand only, the accessories are not dishwasher safe.
– with hot water and a household detergent suitable for use with foods.
WARNING! RISK OF INJURY!
► The cross blade 3is very sharp! Risk of injury!
■ Dry all parts thoroughly, before re-using the appliance.
NOTICE
► Apply a light coating of cooking oil to all metallic components after each
cleaning! Otherwise, metal parts can discolour!
■ You can clean plastic components in the dishwasher. Place the parts in the
upper basket only and ensure that none of the parts can get stuck. This may
cause them to become deformed. If this is not possible, clean the plastic
components in warm water and mild washing-up liquid. Rinse all the parts
off using clean water. Dry all parts well.

SFW 350 C2
■ 16 │ GB│IE│NI│CY
Storage
■ Push the power cable (but not the plug) into the cable storage shaft under
the appliance base. There it is protected from damage.
■ Store the appliance at a dry location.
■ After drying the metal attachments coat them lightly with a little cooking oil –
if you are not going to use the appliance immediately. This will protect them
from corrosion.
■ Store the appliance where it will be out of reach of children and people
requiring supervision. They are not always able to correctly assess the
potential risks involved with using electrical appliances.
Disposal
Do not dispose of the appliance in your normal domestic waste.
This product is subject to the provisions of European Directive
2012/19/EU (Waste Electrical and Electronic Equipment).
Dispose of the appliance through an approved disposal centre or at your com-
munity waste facility. Observe the currently applicable regulations. In case of
doubt, please contact your waste disposal centre.
Dispose of all packaging materials in an environmentally friendly manner.
Kompernass Handels GmbH warranty
Dear Customer,
This appliance has a 3-year warranty valid from the date of purchase. If this product
has any faults, you, the buyer, have certain statutory rights. Your statutory rights
are not restricted in any way by the warranty described below.
Warranty conditions
The validity period of the warranty starts from the date of purchase. Please keep
your original receipt in a safe place. This document will be required as proof of
purchase.
If any material or production fault occurs within three years of the date of purchase
of the product, we will either repair or replace the product for you at our discretion.
This warranty service is dependent on you presenting the defective appliance
and the proof of purchase (receipt) and a short written description of the fault
and its time of occurrence.
If the defect is covered by the warranty, your product will either be repaired or
replaced by us. The repair or replacement of a product does not signify the begin-
ning of a new warranty period.

SFW 350 C2 GB│IE│NI│CY │ 17 ■
Warranty period and statutory claims for defects
The warranty period is not prolonged by repairs effected under the warranty.
This also applies to replaced and repaired components. Any damage and defects
present at the time of purchase must be reported immediately after unpacking.
Repairs carried out after expiry of the warranty period shall be subject to a fee.
Scope of the warranty
This appliance has been manufactured in accordance with strict quality guidelines
and inspected meticulously prior to delivery.
The warranty covers material faults or production faults. The warranty does not
extend to product parts subject to normal wear and tear or fragile parts such as
switches, batteries, baking moulds or parts made of glass.
The warranty does not apply if the product has been damaged, improperly used
or improperly maintained. The directions in the operating instructions for the product
regarding proper use of the product are to be strictly followed. Uses and actions
that are discouraged in the operating instructions or which are warned against
must be avoided.
This product is intended solely for private use and not for commercial purposes.
The warranty shall be deemed void in cases of misuse or improper handling, use
of force and modifications/ repairs which have not been carried out by one of
our authorised Service centres.
Warranty claim procedure
To ensure quick processing of your case, please observe the following instructions:
■ Please have the till receipt and the item number (e.g. IAN 12345) available
as proof of purchase.
■ You will find the item number on the type plate, an engraving on the front
page of the instructions (bottom left), or as a sticker on the rear or bottom of
the appliance.
■ If functional or other defects occur, please contact the service department
listed either by telephone or by e-mail.
■ You can return a defective product to us free of charge to the service address
that will be provided to you. Ensure that you enclose the proof of purchase
(till receipt) and information about what the defect is and when it occurred.
You can download these instructions along with many other manuals,
product videos and software on www.lidl-service.com.