Simex SRP-94 User manual

Assisting the automation
industry since 1986
User manual
METER
SRP-94
•Input type: 0/4-20 mA, 0/1-5V, 0/2-10V
•4 x 20 mm display
Read the user's manual carefully before starting to use the unit or software.
Producer reserves the right to implement changes without prior notice.
2013.12. SRP- 4_INSSXEN_v.2.0 .001

User manual - METER SRP-94
CONTENTS
1. BASIC REQUIREMENTS AND USER SAFETY........................................................................................3
2. GENERAL CHARACTERISTICS................................................................................................................4
3. TECHNICAL DATA......................................................................................................................................4
4. DEVICE INSTALLATION............................................................................................................................6
4.1. UNPACKING.......................................................................................................................................7
4.2. ASSEMBLY........................................................................................................................................7
4.3. CONNECTION METHOD...................................................................................................................9
4.4. MAINTENANCE................................................................................................................................18
5. FRONT PANEL DESCRIPTION................................................................................................................18
6. PRINCIPLE OF OPERATION...................................................................................................................19
6.1. MEASUREMENT MODE..................................................................................................................19
6.2. DETECTION OF THE PEAK VALUES............................................................................................21
6.3. CONTROL OF THE RELAY OUTPUTS..........................................................................................21
6.3.1. O e threshold mode................................................................................................................23
6.3.2. Two thresholds mode..............................................................................................................24
. DEVICE PROGRAMMING.........................................................................................................................25
7.1. PROGRAMMING MENU..................................................................................................................25
7.2. PARAMETERS EDITION.................................................................................................................26
7.2.1. Numeric parameters (digit cha ge mode)...............................................................................26
7.2.2. Numeric parameters (slide cha ge mode)..............................................................................26
7.2.3. Switch parameters (“LIST” type).............................................................................................27
7.3. MENU DESCRIPTION.....................................................................................................................27
7.3.1. “rEL1” me u.............................................................................................................................28
7.3.2. “bEEP” me u...........................................................................................................................30
7.3.3. “i Pt” me u..............................................................................................................................30
7.3.4. ”OutP” me u............................................................................................................................35
7.3.5. ”bri” parameter.........................................................................................................................37
7.3.6. ”HOLd” me u...........................................................................................................................37
7.3.7. ”SECu” me u...........................................................................................................................38
7.3.8. ”rS” me u.................................................................................................................................38
7.3.9. ”Edit” parameter......................................................................................................................39
7.3.10. ”dEFS” parameter..................................................................................................................39
7.3.11. ”SErv” me u..........................................................................................................................39
7.4. MENU STRUCTURE........................................................................................................................40
8. THE ALARM LED......................................................................................................................................42
9. OVER-CURRENT PROTECTION.............................................................................................................42
10. DISPLAYED VALUES CALCULATION..................................................................................................42
10.1. ADDITIONAL CALCULATIONS (USED CONVERSION CHARACTERISTIC).............................42
10.1.1. Li ear characteristic..............................................................................................................43
10.1.2. Square characteristic............................................................................................................43
10.1.3. Square root characteristic.....................................................................................................44
10.1.4. User defi ed characteristic...................................................................................................44
10.1.5. Volume characteristics of a cyli drical ta k..........................................................................45
10.2. EXAMPLES OF CALCULATIONS.................................................................................................46
11. THE MODBUS PROTOCOL HANDLING...............................................................................................51
11.1. LIST OF REGISTERS....................................................................................................................51
11.2. TRANSMISSION ERRORS DESCRIPTION..................................................................................56
11.3. EXAMPLES OF QUERY/ANSWER FRAMES...............................................................................56
12. DEFAULT AND USER'S SETTINGS LIST.............................................................................................59
2

User manual - METER SRP-94
Explanation of symbols used in the manual:
- This symbol de otes especially importa t guideli es co cer i g the i stallatio a d
operatio of the device. Not complyi g with the guideli es de oted by this symbol
may cause a accide t, damage or equipme t destructio .
IF THE DEVICE IS NOT USED ACCORDING TO THE MANUAL THE USER IS
RESPONSIBLE FOR POSSIBLE DAMAGES.
- This symbol de otes especially importa t characteristics of the u it.
Read a y i formatio regardi g this symbol carefully
1. BASIC REQUIREMENTS AND USER SAFETY
- The manufacturer is not responsible for any damages caused by
inappropriate installation, not maintaining the proper environmental
conditions and using the unit contrary to its assignment.
- Installation should be conducted by qualified personnel . During installation all
available safety requirements should be considered. The fitter is responsible for
executing the installation according to this manual, local safety and EMC
regulations.
- If the device is equipped with PE connector, it should be connected to PE wire.
Otherwise PE wire should be connected to GND connector.
- The unit must be properly set-up, according to the application. Incorrect
configuration can cause defective operation, which can lead to unit damage or
an accident.
- If in the case of a unit malfunction there is a risk of a serious threat to the
safety of people or property additional, independent systems and
solutions to prevent such a threat must be used.
- The unit uses dangerous voltage that can cause a lethal accident. The unit
must be switched off and disconnected from the power supply prior to
starting installation of troubleshooting (in the case of malfunction).
- Neighbouring and connected equipment must meet the appropriate standards
and regulations concerning safety and be equipped with adequate overvoltage
and interference filters.
- Do not attempt to disassemble, repair or modify the unit yourself. The unit
has no user serviceable parts. Defective units must be disconnected and
submitted for repairs at an authorized service centre.
- In order to minimize fire or electric shock hazard, the unit must be protected
against atmospheric precipitation and excessive humidity.
3
i
!
!
!

User manual - METER SRP-94
- Do not use the unit in areas threatened with excessive shocks, vibrations, dust,
humidity, corrosive gasses and oils.
- Do not use the unit in areas where there is risk of explosions.
- Do not use the unit in areas with significant temperature variations, exposure to
condensation or ice.
- Do not use the unit in areas exposed to direct sunlight.
- Make sure that the ambient temperature (e.g. inside the control box) does not
exceed the recommended values. In such cases forced cooling of the unit must
be considered (e.g. by using a ventilator).
The unit is designed for operation in an industrial environment and must
not be used in a household environment or similar.
2. GENERAL CHARACTERISTICS
The RP-94 meter is equipped with one current input 0-20 / 4-20mA and one voltage
input 0-5 / 1-5 / 0-10 / 2-10V. Current input has additionally overcurrent protection circuit,
which protects standard resistor. The selection of active input is realised by software, and
selected input can be changed at any time. Additionally the RP-94 allows user to select a
conversion characteristic of several kinds: linear, square, square root, user defined (max.20
points length) and and volume characteristics of a cylindrical tank in the vertical and horizontal
position. Result is showed on 4-digit LED display. Displayed values range can be selected by
user, from - to , plus decimal point.
The device can be equipped with two or four relay (or OC type) outputs. Optionally RP-
94 with two relays (or OC type) outputs can be equipped with active current output, passive
isolated current output or active voltage output. Device RP-94 is equipped with RS-485 /
Modbus RTU communication interface and sensor supply output. The meter can be ordered in
two power supply versions.
RP-94 can be used for controlling and regulation of processes need proportional and
threshold control like: temperature processes (heating or cooling), valves controlling or other.
3. TECHNICAL DATA
Power supply voltage
(depending on version)
External fuse (required)
Power consumption
85...230...260V AC/DC; 50 ÷ 60 Hz (separated)
or 1 ...24...50V DC and 16...24...35V AC (separated)
T - type, max. 2 A
max. 4.5 VA @ 85 ÷ 260V AC/DC
max. 4.5 VA @ 16V ÷ 35V AC
max. 4.5 W @ 1 V ÷ 50V DC
Current input 0÷20 mA, 4÷20 mA overload protected,
maximum input current about 40 mA
Current measurement accuracy ± 0,1% @ 25°C; ± one digit (for 0÷20 mA range)
4
!
!

User manual - METER SRP-94
Current input resistance < 65 Ω (typical 55 Ω)
Accepted prolonged input overload: 20%
Voltage input 0÷5 V, 1÷5 V, 0÷10 V, 2÷10 V
Voltage measurement accuracy ± 0,1% @ 25°C; ± one digit (for 0÷10 V range)
Voltage input resistance > 50 kΩ
Accepted prolonged input overload: 20%
ensor power supply output 24V +5%, -10% / max. 100 mA, stabilized
Relay output 0, 2 or 4 NO, 1A/250V AC (cos ϕ = 1)
OC-type output 0, 2 or 4; 30mA / 30VDC / 100mW
Active current output
(optional, for two relays or two
OC-type output version only)
range max. 0 ÷ 24 mA
Load resistance max. 700 Ω
Passive isolated current output
(optional, for two relays or two
OC-type output version only)
range max. 2.8 ÷ 24 mA
Supply voltage Us = .5 ÷ 36V
Load resistance max. (Us – .5V) / 24mA [kΩ]
Active voltage output
(optional, for two relays or two
OC-type output version only)
range max. 0 ÷ 11V
Load resistance min. 2000 Ω
Temperature stability 50 ppm / °C
Display range - ÷ , plus decimal point
Communication interface RS 485, 8N1 and 8N2, Modbus RTU, not separated
Baud rate 1200 bit/s ÷ 115200 bit/s
5

User manual - METER SRP-94
Display
(depending on version)
LED, 4 digit, 20mm height, red or
LED, 4 digit, 20mm height, green
Data memory non-volatile memory, EEPROM type
Front panel protection IP 65
optional version with panel cut-out sealing available
Terminals protection IP 20
Housing type
Housing material
Housing dimensions
Mounting hole
Assembly depth
Panel thickness
panel
NORYL - GFN2S E1
6 x 48 x 100 mm
0.5 x 43 mm
102 mm
max. 5 mm
Operating temperature
(depending on version)
0°C to +50°C
or -20°C to +50°C
Storage temperature
(depending on version)
-10°C to +70°C
or -20°C to +70°C
Humidity
Altitude
5 to 0% no condensation
up to 2000 meters above sea level
Screws tightening max. torque 0,5 Nm
Max. connection leads cross section 2,5 mm2
Safety requirements according to: PN-EN 61010-1
installation category: II
pollution degree: 2
voltage in relation to ground: 300V AC
insulation resistance: >20MΩ
insulation strength between power supply and
input/output terminal: 1min. @ 2300V
insulation strength between relays terminal:
1min. @ 1350V
EMC according to: PN-EN 61326-1
This is a class A unit. In a residential or a similar area it can cause radio
frequency interference. In such cases the user can be requested to use
appropriate preventive measures.
4. DEVICE INSTALLATION
The unit has been designed and manufactured in a way assuring a high level of user
safety and resistance to interference occurring in a typical industrial environment. In order to
take full advantage of these characteristics installation of the unit must be conducted correctly
and according to the local regulations.
6
!

User manual - METER SRP-94
- Read the basic safety requirements on page 3 prior to starting the installation.
- Ensure that the power supply network voltage corresponds to the nominal
voltage stated on the unit’s identification label.
- The load must correspond to the requirements listed in the technical data.
- All installation works must be conducted with a disconnected power supply.
- Protecting the power supply connections against unauthorized persons must be
taken into consideration.
4.1. UNPACKING
After removing the unit from the protective packaging, check for transportation damage. Any
transportation damage must be immediately reported to the carrier. Also, write down the unit
serial number located on the housing and report the damage to the manufacturer.
Attached with the unit please find:
- user’s manual,
- warranty,
- assembly brackets - 2 pieces.
4.2. ASSEMBLY
- The unit is designed for mounting inside housings (control panel, switchboard)
insuring appropriate protection against surges and interference. Metal housings
must be connected to ground in a way that complies with the governing
regulations.
- Disconnect the power supply prior to starting assembly.
- Check the connections are wired correctly prior to switching the unit on.
In order to install the unit, a 0.5 x 43 mm mounting hole (Figure 4.1, 4.2) must be
prepared. The thickness of the material of which the panel is made must not exceed
5mm. When preparing the mounting hole take the grooves for catches located on
both sides of the housing into consideration (Figure 4.1, 4.2). Place the unit in the
mounting hole inserting it from the front side of the panel, and then fix it using the
brackets (Figure 4.3). The minimum distances between the centre points of multiple
units - due to the thermal and mechanical conditions of operation - are 115 mm x
67mm (Figure 4.4).
7
!
!
!

User manual - METER SRP-94
Figure 4.1. Recomme ded mou ti g hole dime sio s
Figure 4.2. Allowable mou ti g hole dime sio s
Figure 4.3. I stalli g of brackets, a d dime sio s of co ectors.
8
0,5 mm
13 mm
8 mm
8 mm
13 mm
1 mm max. 5 mm
43 mm
1 mm
2 mm
5 mm
12 mm 10 mm
8,5 mm
16 mm
2 mm
max. 5 mm
43 mm

User manual - METER SRP-94
Figure 4.4. Mi imum dista ces whe assembly of a umber of u its
4.3. CONNECTION METHOD
Caution
- Installation should be conducted by qualified personnel . During installation all
available safety requirements should be considered. The fitter is responsible for
executing the installation according to this manual, local safety and EMC
regulations.
- The unit is not equipped with an internal fuse or power supply circuit breaker.
Because of this an external time-delay cut-out fuse with a small nominal current
value must be used (recommended bipolar, max. 2A) and a power supply circuit-
breaker located near the unit. In the case of using a monopolar fuse it must be
mounted on the phase cable (L).
- The power supply network cable diameter must be selected in such a way that in
the case of a short circuit of the cable from the side of the unit the cable shall be
protected against destruction with an electrical installation fuse.
- Wiring must meet appropriate standards and local regulations and laws.
- In order to secure against accidental short circuit the connection cables must be
terminated with appropriate insulated cable tips.
- Tighten the clamping screws. The recommended tightening torque is 0.5 Nm.
Loose screws can cause fire or defective operation. Over tightening can lead to
damaging the connections inside the units and breaking the thread.
- In the case of the unit being fitted with separable clamps they should be inserted
into appropriate connectors in the unit, even if they are not used for any
connections.
- Unused terminals (marked as n.c.) must not be used for connecting any
connecting cables (e.g. as bridges), because this can cause damage to the
equipment or electric shock.
9
!
115 mm
67 mm

User manual - METER SRP-94
- If the unit is equipped with housing, covers and sealing to, protecting against
water intrusion, pay special attention to their correct tightening or clamping. In the
case of any doubt consider using additional preventive measures (covers, roofing,
seals, etc.). Carelessly executed assembly can increase the risk of electric shock.
- After the installation is completed do not touch the unit’s connections when it is
switched on, because it carries the risk of electrical shock.
Due to possible significant interference in industrial installations appropriate measures
assuring correct operation of the unit must be applied. To avoid the unit of improper
indications keep recommendations listed below.
–Avoid running signal cables and transmission cables together with power supply cables
and cables controlling inductive loads (e.g. contactors). Such cables should cross at
a right angle.
–Contactor coils and inductive loads should be equipped with interference protection
systems, e.g. RC-type.
–Use of screened signal cables is recommended. Signal cable screens should be
connected to the earthing only at one of the ends of the screened cable.
–In the case of magnetically induced interference the use of twisted pair of signal cables is
recommended. Twisted pair (best if shielded) must be used with RS-485 serial
transmission connections.
–In the case of measurement or control signals are longer than 30m or go outside of the
building then additional safety circuits are required.
–In the case of interference from the power supply side the use of appropriate interference
filters is recommended. Bear in mind that the connection between the filter and the unit
should be as short as possible and the metal housing of the filter must be connected to
the earth with the largest possible surface. The cables connected to the filter output must
not be run with cables with interference (e.g. circuits controlling relays or contactors).
Connections of power supply voltage and measurement signals are executed using the
screw connections on the back of the unit’s housing.
Figure 4.5. Method of cable i sulatio replaci g a d cable termi als
All connections must be made while power supply is disconnected !
10
!
!
6-7 mm
max. 2 mm

User manual - METER SRP-94
Double numeration means, that depending on device version, particular
terminal can be marked according to the top or bottom number.
Figure 4.6. Termi als descriptio (relay outputs)
Figure 4.7. Termi als descriptio (OC-type outputs)
11
GND DATA+
DATA-
R - 485
+ Uo -
+24V +5%, -10%
Imax = 100mA
1 2 5 6 7 8 9
10 11 12 13 14 15
3 4
31 32 33 34 35
OC1 OC2
- +
OC1 ÷ OC4: Umax = 30V DC,
Imax = 30mA, Pmax = 100mW
OC3
OC4
+ - + -
+ -
(optional) (optional) (optional)
(optional)
Power
supply
(depending on version)
n.c. n.c.
GND
0/1 - 5V, 0/2 - 10V
0/4-20mA
++
Power
supply
(depending on version)
GND DATA+
DATA-
R - 485
+ Uo -
+24V +5%, -10%
Imax = 100mA
1 2 5 6 7 8 9
10 11 12 13 14 15
3 4
31 32 33 34 35
R1 R2 R3
R4
(optional) (optional) (optional)
(optional)
n.c. n.c.
GND
0/1 - 5V, 0/2 - 10V
0/4-20mA
++
16
31

User manual - METER SRP-94
Figure 4.8. Termi als descriptio (relay a d active curre t outputs)
Figure 4.9. Termi als descriptio (OC-type a d active curre t outputs)
Figure 4.10. Termi als descriptio (relay a d passive curre t outputs)
12
GND DATA+
DATA-
R - 485
+ Uo -
+24V +5%, -10%
Imax = 100mA
R1
- +
R2
n.c. n.c.
1 2 5 6 7 8 9
10 11 12 13 14 15
3 4
31 32 33 34 35
Power
supply
(depending on version)
(optional) (optional)
ACTIVE
current output
(optional)
n.c. n.c.
GND
0/1 - 5V, 0/2 - 10V
0/4-20mA
++
GND DATA+
DATA-
R - 485
+ Uo -
+24V +5%, -10%
Imax = 100mA
- +
1 2 5 6 7 8 9
10 11 12 13 14 15
3 4
31 32 33 34 35
OC1 OC2
- +
OC1 ÷ OC2: Umax = 30V DC,
Imax = 30mA, Pmax = 100mW
(opcja)
(opcja)
+ -
n.c. n.c.
ACTIVE
current output
(optional)
Power
supply
(depending on version)
n.c. n.c.
GND
0/1 - 5V, 0/2 - 10V
0/4-20mA
++
GND DATA+
DATA-
R - 485
+ Uo -
+24V +5%, -10%
Imax = 100mA
R1 R2
n.c. n.c.
1 2 5 6 7 8 9
10 11 12 13 14 15
3 4
31 32 33 34 35
Passive, isolated
Current output
4÷20mA
(optional)
Power
supply
(depending on version)
(optional) (optional)
n.c. n.c.
GND
0/1 - 5V, 0/2 - 10V
0/4-20mA
++

User manual - METER SRP-94
Figure 4.11. Termi als descriptio (OC-type a d passive curre t outputs)
Figure 4.12. Termi als descriptio (relay a d active voltage outputs)
Figure 4.13. Termi als descriptio (OC-type a d active voltage outputs)
13
GND DATA+
DATA-
R - 485
+ Uo -
+24V +5%, -10%
Imax = 100mA
1 2 5 6 7 8 9
10 11 12 13 14 15
3 4
31 32 33 34 35
OC1 OC2
- +
OC1 ÷ OC2: Umax = 30V DC,
Imax = 30mA, Pmax = 100mW
+ -
n.c. n.c.
(optional) (optional)
Passive, isolated
Current output
4÷20mA
(optional)
Power
supply
(depending on version)
n.c. n.c.
GND
0/1 - 5V, 0/2 - 10V
0/4-20mA
++
GND DATA+
DATA-
R - 485
+ Uo -
+24V +5%, -10%
Imax = 100mA
R1
- +
R2
n.c. n.c.
1 2 5 6 7 8 9
10 11 12 13 14 15
3 4
31 32 33 34 35
Power
supply
(depending on version)
(optional) (optional)
ACTIVE
voltage output
(optional)
n.c. n.c.
GND
0/1 - 5V, 0/2 - 10V
0/4-20mA
++
GND DATA+
DATA-
R - 485
+ Uo -
+24V +5%, -10%
Imax = 100mA
1 2 5 6 7 8 9
10 11 12 13 14 15
3 4
31 32 33 34 35
OC1 OC2
- +
OC1 ÷ OC2: Umax = 30V DC,
Imax = 30mA, Pmax = 100mW
+ -
n.c. n.c.
(optional) (optional)
Power
supply
(depending on version) - +
ACTIVE
voltage output
(optional)
n.c. n.c.
GND
0/1 - 5V, 0/2 - 10V
0/4-20mA
++

User manual - METER SRP-94
Figure 4.14. Co ectio of 2-wire curre t co verters
Figure 4.15. Co ectio of 3-wire curre t co verters
Figure 4.16. Co ectio of voltage co verters
14
5 6 24V DC
- +
+ -
+
-
+
-
internally connected
16
31
17
32
18
33
19
34
20
35
16
31
17
32
18
33
19
34
20
35
+ -
5 6
-
+
+
-
24V DC
- +
internally connected
16
31
17
32
18
33
19
34
20
35
16
31
17
32
18
33
19
34
20
35
5 6
- +
-
+
+
24V DC
- +
-
+
+
internally connected
16
31
17
32
18
33
19
34
20
35
16
31
17
32
18
33
19
34
20
35

User manual - METER SRP-94
Depe di g o versio :
85...230...260V AC/DC or
19...24...50V DC; 16...24...35V AC
Figure 4.17. Co ectio of power supply a d relays
Contacts of relay outputs are not equipped with spark suppressors. While use
the relay outputs for switching of inductive loads (coils, contactors, power
relays, electromagnets, motors etc.) it is required to use additional
suppression circuit (typically capacitor 47nF/ min. 250VAC in series with
100R/5W resistor), connected in parallel to relay terminals or (better) directly
on the load. In consequence of using the suppression circuit, the level of
generated electromagnetic disturbances is lower, and the life of relay contacts
rises.
15
R4
FU E
1 2
L N
L N
10 11 12 13 14 15
3 4
FU E
R1 R2 R3
!

User manual - METER SRP-94
a) b)
Figure 4.18. Examples of suppressio circuit co ectio :
a) to relay termi als; b) to the i ductive load
Figure 4.19. Example of OC-type outputs co ectio
16
5 610 11
+
voltage input
24 V
-
Logic controller
- +
OC1
+ -
Uo
5 610 11
- +
OC1
+ -
Uo
R
2k2
LED 10 mA
!
N
10 11 10 11
LL
N
!

User manual - METER SRP-94
Figure 4.20. Example of active curre t outputs co ectio
(for device with active curre t output o ly)
Figure 4.21. Example of passive curre t outputs co ectio
(for device with passive curre t output o ly)
Figure 4.22. Example of active voltage outputs co ectio
(for device with active voltage output o ly)
17
+
current input
0-20 mA
-
Logic controller
3 4
- +
ACTIVE
current output
- +
current input
4-20 mA
Logic controller
3 4 5 6
PA IVE
current output Uo
+ -
Isolation loss
!
+
voltage input
0 - 10V
-
Logic controller
3 4
- +
ACTIVE
voltage output

User manual - METER SRP-94
4.4. MAINTENANCE
The unit does not have any internal replaceable or adjustable components available to
the user. Pay attention to the ambient temperature in the room where the unit is operating.
Excessively high temperatures cause faster ageing of the internal components and shorten the
fault-free time of the unit's operation.
In cases where the unit gets dirty do not clean with solvents. For cleaning use warm water with
small amount of detergent or in the case of more significant contamination ethyl or isopropyl
alcohol.
Using any other agents can cause permanent damage to the housing.
Product marked with this symbol should not be placed in municipal waste. Please
check local regulations for disposal of electronic products.
5. FRONT PANEL DESCRIPTION
18
!
MENU
E C ENTER
AL
R1
R2
R3
R4
display
Thresholds exceedi g
LED i dicators (R)
alarm LED i dicator (AL)
programmi g
pushbutto s

User manual - METER SRP-94
Symbols and functions of push-buttons:
Symbol used in the manual: [E C/MENU]
Functions:
• Enter to main menu ( press and hold by at least 2 sec.)
• Exit the current level and Enter to previous menu (or measure mode)
• Cancel the changes made in parameter being edited
Symbol used in the manual: [ENTER]
Functions :
• Start to edit the parameter
• Enter to the sub-menu,
• Confirmation of changes made in parameter being edited
Symbol used in the manual: [^] [v]
Functions :
• Change of the present menu,
• Modification of the parameter value,
• Change of the display mode.
6. PRINCIPLE OF OPERATION
After turning the power supply on, device ID and software version are showed on the
display, next the controller goes to the measurement mode.
6.1. MEASUREMENT MODE
In the measure mode, the measurement results, converted over selected characteristic,
are displayed on the LED display. The measurement range equal to the nominal range is
called: nominal measurement range, and the measurement range equal to the extended
nominal range is called: permissible measurement range (Figure 6.1, 6.2).
Figure 6.1. Defi itio s of measureme t ra ges i mode 4 ÷ 20mA
If the result of measurement exceeds the permissible measurement range, warning ”-Hi-” or
”-Lo-” is displayed rather than input signal, depends on exceeded value (see description of
“Lo r” i “Hi r” parameters, paragraph ”inPt” menu).
19
MENU
E C
ENTER
”Lo r” parameter ”Hi r” parameter
4 mA 20 mA
permissible measurement range
nominal measurement range

User manual - METER SRP-94
Figure 6.2. Defi itio s of measureme t ra ges i mode 0 ÷ 20mA
If the measurement value does not exceed permissible measurement range but
displayed value exceeds range - ÷ , the warning ”-Ov-” is displayed rather
than the calculated result.
In the measurement mode user can check main thresholds values. After pressing [^] or
[v] button, name of the threshold (e.g. ”rEL1”) and his value will be displayed on the display
in alternating mode. If [^] or [v] will be pressed in 5 sec again, the next threshold will be
displayed, else the device comes back to the measurement mode. If a free access is enabled
(see description of ”SECu” menu), user can change the value of particular threshold pressing
button [ENTER] (see: PARAMETERS EDITION).
Input type, range of displaying values, characteristic of conversion, decimal point
position and measure filtering ratio, are user configurable parameters. All accessible
parameters can be changed by entering the menu (see: DEVICE PROGRAMMING). Use the
local keyboard or the remote controller to do it. (Note: all parameters can be remote changed
via RS-485 interface).
Configuration of the device (via menu or RS-485 interface) does not stop
measures.
20
i
”Hi r” parameter
0 mA 20 mA
permissible measurement range
nominal measurement range
i