Simex SWE-73-L User manual

Assisting the automation
industry since 1986
User manual
METER
SWE-7 -L
•Firmware: v.1.00 or higher
•Input type: 4-20 mA
•Supply from current loop 4-20 mA
Read the user's manual carefully before starting to use the unit or software.
Producer reserves the right to implement changes without prior notice.
2017.0 .05 SWE-73-L_INSSXEN_v.1.05.001

User manual - METER SWE-73-L
CONTENTS
1. BASIC REQUIREMENTS AND USER SAFETY........................................................................................3
2. GENERAL CHARACTERISTICS................................................................................................................4
3. TECHNICAL DATA......................................................................................................................................4
4. DEVICE INSTALLATION............................................................................................................................5
4.1. UNPACKING.......................................................................................................................................6
4.2. ASSEMBLY........................................................................................................................................6
4.3. CONNECTION METHOD...................................................................................................................8
4.4. MAINTENANCE................................................................................................................................10
5. DESCRIPTION OF THE FRONT PANEL AND IR REMOTE CONTROLLER PUSH-BUTTONS...........11
6. PRINCIPLE OF OPERATION...................................................................................................................11
6.1. MEASUREMENT MODE..................................................................................................................11
6.2. DETECTION OF THE PEAK VALUES............................................................................................13
6.3. CONTROL OF THE RELAY OUTPUTS..........................................................................................13
6.3.1. On thr shold mod ................................................................................................................15
6.3.2. Two thr sholds mod ..............................................................................................................16
7. DEVICE PROGRAMMING.........................................................................................................................16
7.1. PROGRAMMING MENU..................................................................................................................17
7.2. PARAMETERS EDITION.................................................................................................................17
7.2.1. Num ric param t rs (digit chang mod )...............................................................................17
7.2.2. Switch param t rs (“LIST” typ ).............................................................................................18
7.3. MENU DESCRIPTION.....................................................................................................................18
7.3.1. “rEL” m nu...............................................................................................................................18
7.3.2. “inPt” m nu..............................................................................................................................20
7.3.3. “HOLd” m nu...........................................................................................................................22
7.3.4. “Scod” param t r....................................................................................................................23
7.3.5. “dEFS” param t r....................................................................................................................23
7.3.6. “SErv” m nu............................................................................................................................23
7.4. MENU STRUCTURE........................................................................................................................24
. OVER-CURRENT PROTECTION.............................................................................................................25
9. DISPLAYED VALUES CALCULATION....................................................................................................25
9.1. ADDITIONAL CALCULATIONS (USED CONVERSION CHARACTERISTIC)...............................25
9.1.1. Lin ar charact ristic................................................................................................................26
9.1.2. Squar charact ristic..............................................................................................................26
9.1.3. Squar root charact ristic.......................................................................................................27
9.1.4. Us r d fin d charact ristic.....................................................................................................27
9.2. EXAMPLES OF CALCULATIONS...................................................................................................28
10. DEFAULT AND USER'S SETTINGS LIST.............................................................................................31
Explanation of symbols used in the manual:
- This symbol d not s sp cially important guid lin s conc rning th installation and
op ration of th d vic . Not complying with th guid lin s d not d by this symbol
may caus an accid nt, damag or quipm nt d struction.
IF THE DEVICE IS NOT USED ACCORDING TO THE MANUAL THE USER IS
RESPONSIBLE FOR POSSIBLE DAMAGES.
- This symbol d not s sp cially important charact ristics of th unit.
R ad any information r garding this symbol car fully
2
i
!

User manual - METER SWE-73-L
1. BASIC REQUIREMENTS AND USER SAFETY
- The manufacturer is not responsible for any damages caused by
inappropriate installation, not maintaining the proper environmental
conditions and using the unit contrary to its assignment.
- Installation should be conducted by qualified personnel . During installation all
available safety requirements should be considered. The fitter is responsible for
executing the installation according to this manual, local safety and EMC
regulations.
- The unit must be properly set-up, according to the application. Incorrect
configuration can cause defective operation, which can lead to unit damage or
an accident.
- If in the case of a unit malfunction there is a risk of a serious threat to the
safety of people or property additional, independent systems and
solutions to prevent such a threat must be used.
- Neighbouring and connected equipment must meet the appropriate standards
and regulations concerning safety and be equipped with adequate overvoltage
and interference filters.
- Do not attempt to disassemble, repair or modify the unit yourself. The unit
has no user serviceable parts. Defective units must be disconnected and
submitted for repairs at an authorized service centre.
- In order to minimize fire or electric shock hazard, the unit must be protected
against atmospheric precipitation and excessive humidity.
- Do not use the unit in areas threatened with excessive shocks, vibrations, dust,
humidity, corrosive gasses and oils.
- Do not use the unit in areas where there is risk of explosions.
- Do not use the unit in areas with significant temperature variations, exposure to
condensation or ice.
- Do not use the unit in areas exposed to direct sunlight.
- Make sure that the ambient temperature (e.g. inside the control box) does not
exceed the recommended values. In such cases forced cooling of the unit must
be considered (e.g. by using a ventilator).
The unit is designed for operation in an industrial environment and must
not be used in a household environment or similar.
3
!
!
!

User manual - METER SWE-73-L
2. GENERAL CHARACTERISTICS
The SWE 73 L is a simple digital panel indicator, equipped with one measurement input
(current input, 4-20mA) used simultaneously as device power supply input. Current input has
additionally overcurrent protection circuit, which protects standard resistor.
The SWE 73 L allows user to select a conversion characteristic of several kinds: linear,
square, square root, and user defined (max.20 points length). Result is showed on 4-digit LED
display. Displayed values range can be selected by user, from -999 to 9999, plus decimal
point.
Optionally SWE 73 L can be equipped with bistable relay output. The device can be
configured via IR remote controller. Easy assembling, small dimensions, precision and
reliability are the basic trumps of SWE 73 L indicators.
IR remote controller is not a part of the SWE 73 L and must be ordered separately.
3. TECHNICAL DATA
Minimal supply current 3.5 mA, device supplied from current loop
Measurement loop voltage drop max. 7 V
Current input 4÷20 mA overload protected,
maximum input current about 50 mA
Current measurement accuracy ± 0,1% @ 25°C; ± one digit
Temperature stability 50 ppm / °C
Display range -999 ÷ 9999, plus decimal point
Accepted prolonged input overload: 20%
Relay output bistable 0.5A/30V AC (cos j = 1), min. switching delay:
about 4 sec.
Display LED, 4 digit, 13mm height, red
Data memory non-volatile memory, EEPROM type
Protection level IP 5 (from front - option, IP 40 - standard)
IP 20 (housing and connection clips)
Housing type
Housing material
Housing dimensions
panel
NORYL UL94V-0
72 x 3 x 77 mm
Mounting hole
Assembly depth
7 x 32,5 mm
min. 78 mm
Panel thickness max. 5 mm
Operating temperature
(depending on version)
0°C to +50°C
or -20°C to +50°C
Storage temperature
(depending on version)
-10°C to +70°C
or -20°C to +70°C
4

User manual - METER SWE-73-L
Humidity
Altitude
5 to 90% no condensation
up to 2000 meters above sea level
Screws tightening max. torque 0,5 Nm
Max. connection leads diameter 2,5 mm2
EMC according to: PN-EN 132 -1
This equipment is not intended for use in residential environments and may
not provide adequate protection to radio reception in such environments.
4. DEVICE INSTALLATION
The unit has been designed and manufactured in a way assuring a high level of user
safety and resistance to interference occurring in a typical industrial environment. In order to
take full advantage of these characteristics installation of the unit must be conducted correctly
and according to the local regulations.
- All installation works must be conducted with a disconnected power supply.
- Read the basic safety requirements on page 3 prior to starting the installation.
- All installation works must be conducted with a disconnected power supply.
5
!
!

User manual - METER SWE-73-L
4.1. UNPACKING
After removing the unit from the protective packaging, check for transportation damage. Any
transportation damage must be immediately reported to the carrier. Also, write down the unit
serial number on the housing and report the damage to the manufacturer.
Attached with the unit please find:
- user’s manual,
- warranty,
- assembly brackets - 2 pieces.
4.2. ASSEMBLY
- The unit is designed for mounting inside housings (control panel, switchboard)
insuring appropriate protection against surges and interference. Metal housings
must be connected to ground in a way that complies with the governing
regulations.
- Disconnect the power supply prior to starting assembly.
- Check the connections are wired correctly prior to switching the unit on.
In order to install the unit, a 7 x 32.5 mm mounting hole (Figure 4.1) must be
prepared. The thickness of the material of which the panel is made must not exceed
5mm. Place the unit in the mounting hole inserting it from the front side of the panel,
and then fix it using the brackets (Figure 4.2). The minimum distances between the
centre points of multiple units - due to the thermal and mechanical conditions of
operation - are 91 mm x 57mm (Figure 4.3).
a)
6
!
!
max. 5 mm
7 mm
32,5 mm

User manual - METER SWE-73-L
b)
Figur 4.1. Mounting hol dim nsions: a) r comm nd d b) allowabl
Figur 4.2. Installing of brack ts, and dim nsions of conn ctors.
Figur 4.3. Minimum distanc s wh n ass mbly of a numb r of units
7
91 mm
57 mm
9 mm
-
8 mm
12 mm 10 mm
1 mm
8,5 mm
8 mm
max. 5 mm
32,5 mm

User manual - METER SWE-73-L
4.3. CONNECTION METHOD
Caution
- Installation should be conducted by qualified personnel . During installation all
available safety requirements should be considered. The fitter is responsible for
executing the installation according to this manual, local safety and EMC
regulations.
- Wiring must meet appropriate standards and local regulations and laws.
- In order to secure against accidental short circuit the connection cables must be
terminated with appropriate insulated cable tips.
- Tighten the clamping screws. The recommended tightening torque is 0.5 Nm.
Loose screws can cause fire or defective operation. Over tightening can lead to
damaging the connections inside the units and breaking the thread.
- In the case of the unit being fitted with separable clamps they should be inserted
into appropriate connectors in the unit, even if they are not used for any
connections.
- If the unit is equipped with housing, covers and sealing packing, protecting
against water intrusion, pay special attention to their correct tightening or
clamping. In the case of any doubt consider using additional preventive
measures (covers, roofing, seals, etc.). Carelessly executed assembly can
increase the risk of electric shock.
Due to possible significant interference in industrial installations appropriate measures
assuring correct operation of the unit must be applied. To avoid the unit of improper
indications keep recommendations listed below.
–Avoid common (parallel) leading of signal cables and transmission cables together with
power supply cables and cables controlling induction loads (e.g. contactors). Such cables
should cross at a right angle.
–Contactor coils and induction loads should be equipped with anti-interference protection
systems, e.g. RC-type.
–Use of screened signal cables is recommended. Signal cable screens should be
connected to the earthing only at one of the ends of the screened cable.
–In the case of magnetically induced interference the use of twisted couples of signal
cables (so-called “spirals”) is recommended. The spiral (best if shielded) must be used
with RS-485 serial transmission connections.
–In the case of measurement or control signals are longer than 30m or go outside of the
building then additional safety circuits are required.
–In the case of interference from the power supply side the use of appropriate anti-
interference filters is recommended. Bear in mind that the connection between the filter
and the unit should be as short as possible and the metal housing of the filter must be
connected to the earthing with largest possible surface. The cables connected to the filter
output must not run in parallel with cables with interference (e.g. circuits controlling relays
or contactors).
8
!

User manual - METER SWE-73-L
Connections of measurement signal and relay output are executed using the screw
connections on the back of the unit’s housing.
Figur 4.4. M thod of cabl insulation r placing and cabl t rminals
Figur 4.5. T rminals d scription
Figur 4.6. Conn ction of 2-wir curr nt conv rt rs
9
R
1 2
GND
4 20mA
+
345
ONOFF
-7 mm
max. 2 mm
+
1 2
24V DC
+

User manual - METER SWE-73-L
Figur 4.7. Conn ction of 3-wir curr nt conv rt rs
4.4. MAINTENANCE
The unit does not have any internal replaceable or adjustable components available to
the user. Pay attention to the ambient temperature in the room where the unit is operating.
Excessively high temperatures cause faster ageing of the internal components and shorten the
fault-free time of unit operation.
In cases where the unit gets dirty do not clean with solvents. For cleaning use warm water with
small amount of detergent or in the case of more significant contamination ethyl or isopropyl
alcohol.
Using any other agents can cause permanent damage to the housing.
Product marked with this symbol should not be placed in municipal waste. Please
check local regulations for disposal and electronic products.
10
!
1 2
24V DC
+
+

User manual - METER SWE-73-L
5. DESCRIPTION OF THE FRONT PANEL AND IR REMOTE
CONTROLLER PUSH-BUTTONS
Symbols and functions of push-buttons:
Symbol used in the manual: [ESC/MENU]
Functions:
• Enter to main menu ( press and hold by at least 2 sec.)
• Exit the current level and Enter to previous menu (or measure mode)
• Cancel the changes made in parameter being edited
Symbol used in the manual: [ENTER]
Functions :
• Start to edit the parameter
• Enter to the sub-menu,
• Confirmation of changes made in parameter being edited
Symbol used in the manual: [^] [v]
Functions :
• Change of the present menu,
• Modification of the parameter value,
• Change of the display mode.
6. PRINCIPLE OF OPERATION
Device is supplied from current loop. For proper work of device it is required to guarantee
that signal value of current loop is greater than 3.5 mA. If signal value is to low then running
decimal point is displayed. Device configuration using remote controller is possible if signal
value of current loop is greater than 10 mA (it is signalised by front panel LED marked “IR”).
6.1. MEASUREMENT MODE
In the measure mode, the measurement results, converted over selected characteristic,
are displayed on the LED display. The measurement range equal to the nominal range is
called: nominal measurement range, and the measurement range equal to the extended
nominal range is called: permissible measurement range (figure .1).
11
MENU
ESC
ENTER
programming pushbuttons
infrar d
transmitt r
MENU
ESC
ENTER
R
IR
Thr shold xc ding LED indicator (R)
IR LED confirms th infrar d r c iv r

User manual - METER SWE-73-L
Figur 6.1. D finitions of m asur m nt rang s in mod 4 ÷ 20mA
If the result of measurement exceeds the permissible measurement range, warning
“ Hi ” or “ Lo ” is displayed rather than input signal, depends on exceeded value (see
description of “Lo r” i “Hi r” parameters, paragraph “inPt” menu).
If the measurement value do not exceeds permissible measurement range, but
displayed value exceeds range -999 ÷ 9999, the warning “ Ov ” is displayed rather
than the calculated result.
Range of displaying values, characteristic of conversion, decimal point position and
measure filtering ratio, are user configurable parameters. All accessible parameters can be
changed by entering the menu (see: DEVICE PROGRAMMING). Use the remote controller to
do it.
Configuration of the device via menu do not stops measures.
12
i
“Lo r” parameter “Hi r” parameter
4 mA 20 mA
permissible measurement range
nominal measurement range
i

User manual - METER SWE-73-L
6.2. DETECTION OF THE PEAK VALUES
The SWE 73 L controller is equipped with peaks detection function. It can detect a peaks
of the input signal and display their values. Presets connected with this function are placed in
“HOLd” menu (see description of “HOLd” menu). The detection of the peak can be done if
the measured signal raises and drops of value at least equal to parameter “PEA”. Detected
peaks are displayed during the time defined by parameter “timE”. If a new peak will be
detected while one is displayed, this new peak will be displayed and display time counter will
be cleared (figure .2). If no peaks are detected while time “timE” elapses, device starts to
show the current value of input signal again.
Figur 6.2. Proc ss of p aks d t ction
6.3. CONTROL OF THE RELAY OUTPUTS
Device is equipped with one bistable SPDT relay output. Front panel LED named “R”
indicates the state of the relay output.
After device power on relay is in the same state as it was set while power off (see
parameter “AL” of “rEL” menu description). There is no possibility to change relay state
until 10 seconds elapsed since device power on. During this period it is required to power
device by at least 3.5 mA current. Otherwise the waiting time is extended by the time of waiting
for the correct current. Each next change of the relay state is possible after at least 4 seconds
since last change of the relay state. This delay is also extended by the time of waiting for the
correct current (minimum 3.5 mA). During device power off the relay is set according to the
value of “AL” parameter.
Modes of the control can be changed depend on the values of parameters “SEtP”,
“SEt2”, “HYSt”, “modE” and “AL”. Depend on “modE” parameter, relays can be used or
controlled over one or two thresholds values.
If one threshold is used (figure .3) the relay can be turned on (“modE” = “on”) or off
(“modE” = “oFF”) when the input signal value enters the zone A. If two thresholds are used
(figure .4) the relay will be turned on when value of input signal enters the zone A (“modE” =
“in”) or zone B (“modE” = “out”) and turned off if the signal enters the second one.
13
“timE”
measure
time
“timE”
“PEA”
“PEA”
real measurement result
display value

User manual - METER SWE-73-L
Figur 6.3. On thr shold control of th r lay/LED outputs
Figur 6.4. Two thr shold control of th r lay/LED outputs
The relay output and LED (named “R”) can be controlled depend on both - the
current value and the peak value (when peak detection is active) of the input signal.
14
zone A
zone B
measure
“SEtP” parameter
“HYSt” parameter
state of
relay/LED
zone B
zone A
zone B
measure
“SEtP” or “SEt2” parameter
“HYSt” parameter
state of
relay/LED
i

User manual - METER SWE-73-L
6.3.1. One threshold mode
Figure .5 presents the principle of relay outputs operation for one threshold mode, and
an example values of other parameters.
Description:
A, B, C, D - points where measured signal exceeds border values (expected value ± allowed deviation)
tA , tB , tC , tD - time periods while input signal is in zone A or zone B
Figur 6.5. Principl of LED/r lay output op ration for on thr shold mod
Parameter “SEtP” sets a threshold of the relay, and parameter “HYSt” sets
a hysteresis of the relay (figure .5 a). The relay can change his state only when input value
exceeds (over or under) border value. Border values means values equal
threshold+hysteresis and threshold-hysteresis respectively.
The relay state will be changed as soon as input value exceeds any of the
border values (see points A and C, figure .5 a, b, c) but only if at least 4 seconds elapsed
since last change of the relay state, in the other case relay state will be changed after required
delay (4 sec).
The state of relay output while the input value exceeds the border values (points A, B, C,
D) is described by parameter “modE”. The relay can be turned on (“modE” = “on”), or
turned off (“modE” = “oFF”) when input signal value enters the zone A (figure .5 a).
The parameter “AL” allow user to set the relay output behaviour in critical situations (e.
g. Input values exceeds permissible measurement range). User can select that the relays
will be turned on, turned off,or not changed in critical situations.
All parameters connected with relay outputs are described in paragraph “rEL” menu.
15
“SEtP” parameter
(expected signal value)
“HYSt” parameter
(allowed signal
deviation)
measured
signal
displayed value
time
time
AB
CD
relay state
(modE = on)
tAtBtCtD
BON
DOFF
relay state
(modE = oFF)
BOFF
DON
time
closed
open
a)
b)
c)
open
closed
zone A
zone B

User manual - METER SWE-73-L
6.3.2. Two thresholds mode
Description:
A, B, C, D, E - points where measured signal exceeds border values (expected value ± allowed deviation)
tA , tB , tC , tD , tE- time periods while input signal is in zone A or zone B
Figur 6.6. Principl of LED/r lay output op ration for two thr sholds mod
Figure . presents the principle of relay outputs operation for two thresholds mode, and
an example values of other parameters. In this mode parameter “SEt2” is accessible in
common with “SEtP”, this parameter describes a second threshold of the relay output. The
parameters “HYSt”, “modE” and “AL” are connected with both “SEtP” and “SEt2”
thresholds. While the controlling process, the relay output changes his state depends of both
“SEtP” and “SEt2” thresholds in similar way as it was described in one threshold mode.
If two threshold mode is used, “modE” parameter defines state of the relay output when
the input value occurs in a particular zone defined by border values of both thresholds. The
relay can be turned on if the input value enters the zone A (“modE” = “in”) or zone B
(“modE” = “out”) and turned off if it enters the second one (figure . ).
The sequence of thresholds “SEtP” and “SEt2” can be set in any order, due to the
control of relay outputs is done depend on difference between thresholds values
(zone A ) and outside of threshold values (zone B).
7. DEVICE PROGRAMMING
The device menu allow user to set all parameters connected to operation of
measurement input, control modes, critical situations behaviour and access settings. The
meaning of the particular parameters is described in paragraph MENU DESCRIPTION.
16
i
EOFF “SEtP” or “SEt2”
parameter
“HYSt” parameter
measure
d signal
displayed value
time
time
AB
C
D
relay state
(modE = in)
tAtCtD
BON
relay state
(modE = out)
BOFF
EON
time
closed
open
a)
b)
c)
open
closed
zone A
zone B
“HYSt” parameter
zone B COFF CON
E
tBtE

User manual - METER SWE-73-L
The device can be configured via IR remote controller but it must be supplied at
least by 10mA current and the temperature must be at least 0°C in order to do that.
7.1. PROGRAMMING MENU
To enter main menu (being in the measurement mode) operator must to press and hold
at least 2 sec. [ESC/MENU] button.
If the user password is defined (see parameter “Scod”), operator have to enter correct
one before proceeding to menu options . Entering of the passwords is similar to the edition of
numeric parameters (see: PARAMETERS EDITION ), however presently editing digit is showed
only on the display, other digits are replaced by “-” sign.
After entering of last digit of the password first menu position will be displayed (if the password
is correct) or warning “Err” in other case.
Functions of the buttons while sub-menu and parameters choice:
Selection of sub-menu or parameter for editing. Name of selected item (sub-
menu or parameter) is displayed.
Operation of [ENTER] button depend on present menu position:
• if the name of some sub-menu is displayed - enter this sub-menu; name
of the first parameter (or next level sub-menu) is displayed,
• if the name of some parameter is displayed - enter the edition of this
parameter; present value of the parameter is displayed,
[ESC/MENU] button allow user to exit present menu level and goes to upper
level menu (or measurement mode).
After about 1 min. since last use of the buttons, device exits the menu mode and
returns to the measurement mode (only if no parameters are in editing mode).
7.2. PARAMETERS EDITION
To start edition of any parameter user should select name of desired one using [^] [v]
buttons and then press [ENTER].
7.2.1. Numeric parameters (digit change mode)
Numerical parameters are displayed as decimal numbers. The mode of its new value
entering depends on chosen edit method ( see parameter “Edit”).
In mode “by digit” (“Edit”=“dig”) pressing one of the keys [^] or [v] causes change of
current position (flashing digit) or the sign (+/-). Short pressing of the [ENTER] button causes
change of the position (digit).
Press [ENTER] at least 2 seconds to accept the changes, after that question “SEt?” is
displayed, and user must to confirm (or cancel) the changes. To conform changes (and story it
in EEPROM) press [ENTER] button shortly after “SEt?” is displayed. To cancel the changes
press [ESC] button shortly after “SEt?” is displayed. After that device returns to the menu.
17
i
ENTER
MENU
ESC
i

User manual - METER SWE-73-L
7.2.2. Switch parameters (“LIST” type)
Switch parameters can be described as a sets of values (a lists) out of which only one of
the options available on the list can be selected for the given parameter. Options of switching
parameter are selected using [^], [v] keys.
Short pressing of [ENTER] causes in displaying of the acknowledge question (“SEt?”). If
key [ENTER] is pressed again, the changes are accepted, stored in EEPROM end the edition
process finished. Pressing the key [ESC] after “SEt?” causes in cancelling of made changes
and returning to menu.
Functions of buttons when editing numeric and switching parameters:
While editing numeric parameter - change of current (flashing) digit.
While editing switch parameter - selection of switch parameter.
If numerical parameter is being edited, a short press of [ENTER] button
change edited position. A long press of [ENTER] button (at lest 2 sec.)
causes of display a “SEt?” ask, which allow user to make sure if change of
the parameter value is correct. If switch parameter is being edited, a short
press of [ENTER] button causes of display a “SEt?” ask. When [ENTER]
button is pressed again (while “SEt?” is displayed) the new value of the
parameter is stored in EEPROM memory.
Pressing this button operator can cancel the changes done up to now (if they
were not approved by [ENTER] button after the “SEt?” ask) and come back
to menu
7.3. MENU DESCRIPTION
“ ” - password checking. If some password different from “0000” is set, then every
enter to main menu follows the entering of password. If entered password is
correct then first menu position will be displayed else warning “Err”, and unit
returns to measurement mode.
Due to problem with direct displaying of “m” letter, it is exchanged with special sign
“ ”. Independently in user manual letter “m” is used to make it more readable
(example: “modE”).
7.3.1. “rEL” menu
This menu allows to configure the operation mode of relay and LED marked “R”.
Principle of the relays operation is described in paragraph CONTROL OF THE RELAY
OUTPUTS.
The relay output and LED (named R) can be controlled depend on both - the current
value and the peak value (when peak detection is active) of the input signal.
“SEtP” - first threshold of the relay (range -999 ÷ 9999). Negative values can be input by
selecting a “-” sign on first digit (to change value use [^] and [v] buttons).
Threshold is the medium value of relay hysteresis.
18
i
MENU
ESC
ENTER
i

User manual - METER SWE-73-L
“SEt2” - second threshold of the relay (range -999 ÷ 9999). Negative values can be input
by selecting a “-” sign on first digit ( to change value use [^] and [v] buttons). This
threshold is accessible when “modE” parameter is set to “in” or “out” value.
Threshold is the medium value of relay hysteresis.
“HYSt” - hysteresis of relay (range 0 ÷ 999). Full hysteresis of the relay is equal to 2x
“HYSt” parameter. The relay state can change when an input signal is out of
threshold hysteresis to threshold+hysteresis zone.
Presented parameters should be set to ensure that “SEtP” + “HYSt”,
“SEt2” + “HYSt”, “SEtP” “HYSt” or “SEt2” “HYSt” do not exceeds the
measure range. Additionally, in two threshold mode (“modE”= “in” or “out”),
the hysteresis for both thresholds must not cover each other (in other case relay
can't change his state).
“modE” - relay operation mode:
“noAc” - the relay is not active (permanently turned OFF)
“on” - one threshold mode, the relay turns ON when input signal exceeds from
the bottom SEtP+HYSt value, and turns OFF when exceeds from the top
SEtP HYSt,
“oFF” - one threshold mode, the relay turns ON when input signal exceeds from
the top SEtP HYSt value, and turns OFF when exceeds from the bottom
SEtP+HYSt,
“in” - two threshold mode, the relay turns ON when the input signal exceeds
from the bottom “lower threshold + HYSt” or from the top
“bigger threshold - HYSt”, and turns OFF when exceeds from the top
“lower threshold HYSt” or from the bottom
“bigger threshold + HYSt”. The bigger threshold means bigger one of
“SEtP” and “SEt2” thresholds, the lower threshold means lower one of
“SEtP” and “SEt2” thresholds.
“out” - two threshold mode, the relay turns ON when the input signal exceeds
from the top “lower threshold HYSt” or from the bottom
“bigger threshold + HYSt”, and turns OFF when exceeds from the
bottom “lower threshold + HYSt” or from the top
“bigger threshold - HYSt”. The bigger threshold means bigger one of
“SEtP” and “SEt2” thresholds, the lower threshold means lower one of
“SEtP” and “SEt2” thresholds.
•LED lights when “ON” part of the relay is closed, independently of relay
mode.
• When power supply fail, unit sets relay state accordingly to “AL” parameter.
19
i
i

User manual - METER SWE-73-L
“AL” - this parameter defines the relay reaction when some critical situations occurs:
“noCH” - relay do not change his state,
“on” - relay will be turned ON,
“oFF” - relay will be turned OFF.
If parameter “modE” is set to “on” , “oFF”, “in” or “Out” the “critical situation”
means that allowable measurement range is exceeded.
•If option “noCH” is selected for “AL” parameter, behaviour of the relay may
depend on “FiLt” parameter in some cases. If “FiLt” is set to big value and the
input signal drops, result value of the measure will change slow, causes of
turning on or off relay due to thresholds values. The critical situation is slowly
detected, so it is impossible to predict the relay state in that situations.
•If parameter “AL” = “on”, the relay will be turned on in the critical situations,
even if his parameter “modE” = “noAC”.
7.3.2. “inPt” menu
This menu presets the measurement input:
“CHAr” - this option presets type of the conversion characteristic, and can be set to:
“Lin” - linear
“Sqr” - square
“Sqrt” - square root
When one of those characteristics is chosen display
range is defined by “Lo C” and “Hi C”.
“USEr” - user defined characteristic. Maximal length 20 points. Every point is
defined by user. Adding, Editing and Deleting of points is done by options
“AddP”, “EdtP”, “dELP” (“InPt” menu) respectively.
If user defined characteristic is selected, and if number of defined points is lower
than 2 then warning “Errc” is displayed in measurement mode.
The process of displayed result calculation is described in details in DISPLAY VALUES
CALCULATION paragraph.
“FiLt” - this parameter sets filtration rate. It can be set to values from 0 (no filtration ) to 5
(strongest filtration – time window about 3 sec).
“Pnt” - decimal point position. It can be set to one of:
“ 0”, “ 0.0”, “ 0.00”, “0.000”
Decimal point position is changed by [^], [v] buttons.
20
i
i