Simex SPP-638 User manual

Assisting the automation
industry since 1986
User manual
FLOW METER
PP-638
•Firmware: v.6.01 or higher
•Input type: 0/4-20 mA
•Batching and tota izer function
Read the user's manual carefully before starting to use the unit or software.
Producer reserves the right to implement changes without prior notice.
2018.12.20 PP-638_IN XEN_v.1.04.001

User manual - FLOW METER SPP-638
CONTENTS
1. BASIC REQUIREMENTS AND USER SAFETY........................................................................................4
2. GENERAL CHARACTERISTICS................................................................................................................5
3. TECHNICAL DATA......................................................................................................................................6
4. DEVICE INSTALLATION............................................................................................................................8
4.1. UNPACKING.......................................................................................................................................8
4.2. ASSEMBLY........................................................................................................................................9
4.3. CONNECTION METHOD...................................................................................................................9
4.4. MAINTENANCE................................................................................................................................16
5. FRONT PANEL DESCRIPTION................................................................................................................17
6. PRINCIPLE OF OPERATION...................................................................................................................18
6.1. MEASUREMENT MODE..................................................................................................................18
6.2. DETECTION OF THE PEAK VALUES............................................................................................21
6.3. CONTROL OF THE RELAY OUTPUTS..........................................................................................22
6.3.1. On thr shold mod ................................................................................................................24
6.3.2. Two thr sholds mod ..............................................................................................................25
6.3.3. Batch r mod and „PrE r1” mod ...........................................................................................26
6.3.4. Us of th batch r count r as a mark r.................................................................................27
7. DEVICE PROGRAMMING.........................................................................................................................28
7.1. PROGRAMMING MENU..................................................................................................................28
7.2. PARAMETERS EDITION.................................................................................................................29
7.2.1. Num ric param t rs (digit chang mod )...............................................................................29
7.2.2. Num ric param t rs (slid chang mod )..............................................................................29
7.2.3. Switch param t rs (“LIST” typ ).............................................................................................30
7.3. MENU DESCRIPTION.....................................................................................................................30
7.3.1. “rELAy1” m nu........................................................................................................................30
7.3.2. “bEEP” m nu...........................................................................................................................34
7.3.3. “FLouu” m nu..........................................................................................................................34
7.3.4. “bAtCH” m nu.........................................................................................................................38
7.3.5. “totAL” m nu............................................................................................................................39
7.3.6. “Pr inP” m nu..........................................................................................................................40
7.3.7. “Init d” param t r.....................................................................................................................41
7.3.8. “FiLtEr” m nu..........................................................................................................................41
7.3.9. ”OutP” m nu............................................................................................................................41
7.3.10. ”briGHt” param t r................................................................................................................45
7.3.11. ”HOLd” m nu.........................................................................................................................45
7.3.12. ”SECU” m nu........................................................................................................................46
7.3.13. ”rS-485” m nu.......................................................................................................................46
7.3.14. ”Edit t” param t r..................................................................................................................47
7.3.15. ”dEFS” param t r..................................................................................................................47
7.3.16. ”SErv” m nu..........................................................................................................................47
7.4. UNITS CALCULATIONS EXAMPLES.............................................................................................48
7.4.1. Units r calculating xampl s..................................................................................................49
7.5. MENU STRUCTURE........................................................................................................................50
8. OVER CURRENT PROTECTION.............................................................................................................52
9. DISPLAYED VALUES CALCULATION....................................................................................................52
9.1. ADDITIONAL CALCULATIONS (USED CONVERSION CHARACTERISTIC)...............................52
9.1.1. Lin ar charact ristic................................................................................................................52
9.1.2. Squar charact ristic..............................................................................................................53
9.1.3. Squar root charact ristic.......................................................................................................54
9.1.4. Us r d fin d charact ristic.....................................................................................................54
9.2. EXAMPLES OF CALCULATIONS...................................................................................................55
10. THE MODBUS PROTOCOL HANDLING...............................................................................................59
10.1. LIST OF REGISTERS....................................................................................................................59
10.2. TRANSMISSION ERRORS DESCRIPTION..................................................................................68
10.3. EXAMPLES OF QUERY/ANSWER FRAMES...............................................................................68
2

User manual - FLOW METER SPP-638
11. DEFAULT AND USER'S SETTINGS LIST.............................................................................................71
3

User manual - FLOW METER SPP-638
Explanation of symbols used in the manual:
- This symbol d not s sp cially important guid lin s conc rning th installation and
op ration of th d vic . Not complying with th guid lin s d not d by this symbol
may caus an accid nt, damag or quipm nt d struction.
IF THE DEVICE IS NOT USED ACCORDING TO THE MANUAL THE USER IS
RESPONSIBLE FOR POSSIBLE DAMAGES.
- This symbol d not s sp cially important charact ristics of th unit.
R ad any information r garding this symbol car fully
1. BASIC REQUIREMENTS AND USER SAFETY
-


- Installation should be conducted by qualified personnel . During installation all
available safety requirements should be considered. The fitter is responsible for
executing the installation according to this manual, local safety and EMC
regulations.
- If the device is equipped with PE connector, it should be connected to PE wire.
Otherwise PE wire should be connected to GND connector.
- The unit must be properly set-up, according to the application. Incorrect
configuration can cause defective operation, which can lead to unit damage or
an accident.
- 


- 


- Neighbouring and connected equipment must meet the appropriate standards
and regulations concerning safety and be equipped with adequate overvoltage
and interference filters.
-


4
i
!
!

User manual - FLOW METER SPP-638
- Do not use the unit in areas threatened with excessive shocks, vibrations, dust,
humidity, corrosive gasses and oils.
- Do not use the unit in areas where there is risk of explosions.
- Do not use the unit in areas with significant temperature variations, exposure to
condensation or ice.
- Do not use the unit in areas exposed to direct sunlight.
- Make sure that the ambient temperature (e.g. inside the control box) does not
exceed the recommended values. In such cases forced cooling of the unit must
be considered (e.g. by using a ventilator).


2. GENERAL CHARACTERISTICS
Main task of !!"#$%is measurement of instantaneous flow (flow rate), and counting of
total flow (e.g. passage of fluid or gas ), The device can be used as regulator, to control
industrial process. Measurement of instantaneous flow can be indicated in range: 0 to
999999 (plus decimal point) and can be expressed in any scalable user units of flow and three
time measures (second, minute, hour). Total flow can be indicated in range from 0.000 to
4294967295 user units with maximum resolution of 0.00001 units.
!!"#$% can cooperate with flow sensors with current output (0-20mA or 4-20mA).
ensors can be powered from sensor supply output (stabilized, 24VDC +5%, -10% 100mA).
The meter is equipped in 2 or 4 relay outputs or Open Collector outputs, which can be
driven due to instantaneous flow, total flow or batcher counter value. It can also not have any
outputs at all. Optionally !!"#$% with two relays outputs (or OC-type outputs) can be
equipped with active current output, passive isolated current output or active voltage output.
Build in R 485 interface enables access to all internal registers, and supports MODBU RTU
communication protocol. The controller can be ordered in two power supply versions.
Optionally the meter (in version with four relay outputs or four OC-type outputs) can be
equipped with active current output, passive isolated current output or active voltage output.
Modern design guarantees high operational reliability. Front panel is protected from dust
and water spatters.
Additional features:
• alarm preset; alarm signal is released when measurement exceeds measurement range
• direct access to relays thresholds settings, without password,
• batcher mode.
5
!
!

User manual - FLOW METER SPP-638
3. TECHNICAL DATA
Power supply voltage
(depending on version)
External fuse (required)
Power consumption
85...&$'...260V AC/DC; 50 ÷ 60 Hz (separated)
or 19...&(...50V DC and 16...&(...35V AC (separated)
T - type, max. 2 A
max. 29 VA @ 85 ÷ 260V AC/DC
max. 13 VA @ 16V ÷ 35V AC
max. 8.683 W @ 19V ÷ 50V DC
) 0÷20 mA, 4÷20 mA overload protected,
maximum input current about 40 mA
Current measurement accuracy ± 0,1% @ 25°C; ± one digit (for 0÷20 mA range)
Measurement input resistance: 50 W
Accepted prolonged input overload: 20%
!
low level:
high level:
not separated
0V ÷ 1V
10V ÷ 30V (about. 12 mA @ 24V)
 24V +5%, -10% / max. 100 mA, stabilized
* 1, 2 or 4 NO 1A/250V AC (cos j = 1)
+)" 1, 2 or 4; 30mA / 30VDC / 100mW
,
(optional, for two relays or two
OC-type output version only)
range max. 0 ÷ 24 mA
Load resistance max. 700 W
!
(optional, for two relays or two
OC-type output version only)
range max. 2.8 ÷ 24 mA
upply voltage Us = 9.5 ÷ 36V
Load resistance max. (Us – 9.5V) / 24mA [kW]
6

User manual - FLOW METER SPP-638
,
(optional, for two relays or two
OC-type output version only)
range max. 0 ÷ 11V
Load resistance min. 2000 W
Instantaneous flow range 0 ÷ 9999, plus decimal point
Temperature stability 50 ppm / °C
Instantaneous flow precision elected from range: 0 ÷ 0.000
Instantaneous flow unit User unit per min. or sec. or hour
Total flow range over 4 x 109 units (max. 16 digits )
Total flow precision elected from range: 0 ÷ 0.000
Total flow unit Any, with precision, settable by user
Batcher counter range 65536 units
Batcher counter precision elected from range: 0 ÷ 0.000
Batcher counter unit Any, with precision, settable by user
Number of batches counter range 0 ÷ 999999
Communication interface R 485, 8N1 and 8N2, Modbus RTU, not separated
Baud rate 1200 bit/s ÷ 115200 bit/s
Display
(depending on version)
LED, 6 digit, 38 mm height, red (l = 660 nm)
LED, 6 digit, 38 mm height, pure green (l = 520 nm)
LED, 6 digit, 38 mm height, blue (l = 470 nm)
Data memory non-volatile memory, EEPROM type
Protection level of device IP 67
Housing type
Housing material
Wall mounted, T-type
AB (lower part) + PC (upper part)
Operating temperature
(depending on version)
0°C to +50°C
or -20°C to +50°C
torage temperature
(depending on version)
-10°C to +70°C
or -20°C to +70°C
Humidity
Altitude
5 to 90% no condensation
up to 2000 meters above sea level
crews tightening max. torque 0,5 Nm
Max. connection leads cross section 2,5 mm2
afety requirements according to: PN-EN 61010-1
installation category: II
pollution degree: 2
voltage in relation to ground: 300V AC
7

User manual - FLOW METER SPP-638
insulation resistance: >20MW
insulation strength between power supply and
input/output terminal: 1min. @ 2300V
insulation strength between relays terminal:
1min. @ 1350V
EMC according to: PN-EN 61326-1
-
-
4. DEVICE INSTALLATION
The unit has been designed and manufactured in a way assuring a high level of user
safety and resistance to interference occurring in a typical industrial environment. In order to
take full advantage of these characteristics installation of the unit must be conducted correctly
and according to the local regulations.
- Read the basic safety requirements on page 4 prior to starting the installation.
- Ensure that the power supply network voltage corresponds to the nominal
voltage stated on the unit’s identification label.
- The load must correspond to the requirements listed in the technical data.
- All installation works must be conducted with a disconnected power supply.
- Protecting the power supply clamps against unauthorized persons must be
taken into consideration.
4.1. UNPACKING
After removing the unit from the protective packaging, check for transportation damage. Any
transportation damage must be immediately reported to the carrier. Also, write down the unit
serial number on the housing and report the damage to the manufacturer.
Attached with the unit please find:
- user’s manual,
- warranty,
8
!
!

User manual - FLOW METER SPP-638
4.2. ASSEMBLY
- Disconnect the power supply prior to starting assembly.
- Check the connections are wired correctly prior to switching the unit on.
To install device on the wall, a pinholes should be made. .  (/ presents
dimensions of the device and distances between holes. The back side of the device
has four mounting holes. This part of the case should be mounted to a wall by
screws.
Figur 4.1. D vic and ass mbly dim nsions of th cas
4.3. CONNECTION METHOD
Caution
- Installation should be conducted by qualified personnel . During installation all
available safety requirements should be considered. The fitter is responsible for
executing the installation according to this manual, local safety and EMC
regulations.
- The unit is not equipped with an internal fuse or power supply circuit breaker.
Because of this an external time-delay cut-out fuse with minimal possible nominal
current value must be used (recommended bipolar, max. 2A) and a power supply
circuit-breaker located near the unit. In the case of using a monopolar fuse it must
be mounted on the phase cable (L).
- The power supply network cable diameter must be selected in such a way that in
the case of a short circuit of the cable from the side of the unit the cable shall be
protected against destruction with an electrical installation fuse.
9
!
!
!
f
4.4
f
8.4
212 mm
112 mm
230 mm
140 mm
96.5 mm

User manual - FLOW METER SPP-638
- Wiring must meet appropriate standards and local regulations and laws.
- In order to secure against accidental short circuit the connection cables must be
terminated with appropriate insulated cable tips.
- Tighten the clamping screws. The recommended tightening torque is 0.5 Nm.
Loose screws can cause fire or defective operation. Over tightening can lead to
damaging the connections inside the units and breaking the thread.
- In the case of the unit being fitted with separable clamps they should be inserted
into appropriate connectors in the unit, even if they are not used for any
connections.
"0

-
- If the unit is equipped with housing, covers and sealing packing, protecting
against water intrusion, pay special attention to their correct tightening or clamping.
In the case of any doubt consider using additional preventive measures (covers,
roofing, seals, etc.). Carelessly executed assembly can increase the risk of electric
shock.
- After the installation is completed do not touch the unit’s connections when it is
switched on, because it carries the risk of electrical shock.



–Avoid common (parallel) leading of signal cables and transmission cables together with
power supply cables and cables controlling induction loads (e.g. contactors). uch cables
should cross at a right angle.
–Contactor coils and induction loads should be equipped with anti-interference protection
systems, e.g. RC-type.
–Use of screened signal cables is recommended. ignal cable screens should be
connected to the earthing only at one of the ends of the screened cable.
–In the case of magnetically induced interference the use of twisted couples of signal
cables (so-called “spirals”) is recommended. The spiral (best if shielded) must be used
with R -485 serial transmission connections.
–In the case of measurement or control signals are longer than 30m or go outside of the
building then additional safety circuits are required.
–In the case of interference from the power supply side the use of appropriate anti-
interference filters is recommended. Bear in mind that the connection between the filter
and the unit should be as short as possible and the metal housing of the filter must be
connected to the earthing with largest possible surface. The cables connected to the filter
output must not run in parallel with cables with interference (e.g. circuits controlling relays
or contactors).
10
!

User manual - FLOW METER SPP-638
Connections of power supply voltage and measurement signals are executed using the
screw connections on the back of the unit’s housing.
Figur 4.2. M thod of cabl insulation r placing and cabl t rminals
1 ,2
1 .

1 )
 !!"#$%
Figur 4.3. T rminals d scription (two r lay outputs)
Figur 4.4. T rminals d scription (two OC-typ outputs)
11
!
6-7 mm
max. 2 mm
!3
/ &
!

(depending on version)
$ (
*/

4
*&

5 % 6 /' // /&#
7
"08
,,8
,,"
97
8&(: +5%, -10%
Imax = 100mA
/$ /( /4 /# /5 /% /6 &' &&&/


'"&',
("&',
978

!3
/ &
!

(depending on version)
"08
,,8
,,"
97
8&(: +5%, -10%
Imax = 100mA
/$ /( /4 /# /5$ ( 4 5 % 6 /' // /&
+)/;+)&< Umax = 30V DC,
Imax = 30mA, Pmax = 100mW
" 8
+)&

" 8
+)/

#
7
/% /6 &' &&&/


'"&',
("&',
978


User manual - FLOW METER SPP-638
Figur 4.5. T rminals d scription (four r lay and on OC-typ output)
Figur 4.6. T rminals d scription (two r lay, on OC-typ and activ curr nt outputs)
Figur 4.7. T rminals d scription (two r lay, on OC-typ and passiv curr nt outputs)
Figur 4.8. T rminals d scription (two r lay, on OC-typ and activ voltag outputs)
12
!3
/ &
!

(depending on version)
"08
,,8
,,"
97
8&(: +5%, -10%
Imax = 100mA
/$ /( /4 /# /54 5 % 6 /' // /&
+)&< Umax = 30V DC,
Imax = 30mA, Pmax = 100mW
" 8
+)&

#
7
$ (
*/

/% /6 &' &&&/


'"&',
("&',
978

!3
/ &
!

(depending on version)
$ ( 5 % // /&
"08
,,8
,,"
97
8&(: +5%, -10%
Imax = 100mA
/$ /( /4 /# /5
+)$< Umax = 30V DC,
Imax = 30mA, Pmax = 100mW
8 "
+)$

ACTIVE
current output

" 8
*/

4
*&

# 6 /'
 
/% /6 &' &&&/


'"&',
("&',
978

!3
/ &
!

(depending on version)
$ ( 5 % // /&
"08
,,8
,,"
97
8&(: +5%, -10%
Imax = 100mA
/$ /( /4 /# /5
8 "
+)$

!
)
(;&',

+)$< Umax = 30V DC,
Imax = 30mA, Pmax = 100mW
$ (
*/

4
*&

# 6 /'
 
/% /6 &' &&&/


'"&',
("&',
978

!3
/ &
!

(depending on version)
$ ( 5 % // /&
"08
,,8
,,"
97
8&(: +5%, -10%
Imax = 100mA
/$ /( /4 /# /5
+)$< Umax = 30V DC,
Imax = 30mA, Pmax = 100mW
8 "
+)$

ACTIVE
voltage output

" 8
6 /'
 
*/

4
*&

# /% /6 &' &&&/


'"&',
("&',
978


User manual - FLOW METER SPP-638
Figur 4.9. T rminals d scription (four r lay outputs)
Figur 4.10. T rminals d scription (four OC-typ outputs)
D p nding on v rsion:
85...230...260V AC/DC or
19...24...50V DC; 16...24...35V AC
Figur 4.11. Conn ction of pow r supply and r lays
13
!3
/ &
!

(depending on version)
$ (
*/

4 #
*&

5 %
*$

6 /'
*(

7
// /&
"08
,,8
,,"
97
8&(: +5%, -10%
Imax = 100mA
/$ /( /4 /# /5 /% /6 &' &&&/


'"&',
("&',
978

!3
/ &
!

(depending on version)
$ ( 4 # 5 % 6 /'
"08
,,8
,,"
97
8&(: +5%, -10%
Imax = 100mA
/$ /( /4 /# /5
8 "
+)(

8 "
+)$

" 8
+)&

" 8
+)/

+)/;+)(< Umax = 30V DC,
Imax = 30mA, Pmax = 100mW
7
// /& /% /6 &' &&&/


'"&',
("&',
978

/ & $ (
*/
4 #
*&
5 %
*$
6 /'
*(
= 7
FU E
FU E
= 7

User manual - FLOW METER SPP-638
)->
  
            -       
         (5.?   &4':,)     
/''*?4>
      -           


a) b)
Figur 4.12. Exampl s of suppr ssion circuit conn ction:
a) to r lay t rminals; b) to th inductiv load
Figur 4.13. Exampl of OC-typ outputs conn ction
14
!
!
7
$ ( $ (
==
7
!
6 /'
0
/# /5
+)
+
Voltage input
24 V
-
Logic controller
"8
8"
6 /'
0
/# /5
+) "8 8"
*&&=3/',

User manual - FLOW METER SPP-638
Figur 4.14. Exampl of activ curr nt outputs conn ction
(for d vic with activ curr nt output only)
Figur 4.15. Exampl of passiv curr nt outputs conn ction
(for d vic with passiv curr nt output only)
Figur 4.16. Exampl of activ voltag outputs conn ction
(for d vic with activ voltag output only)
15
// /&
ACTIVE
current
output

" 8
+
current input
0-20 mA
-
Logic controller
// /&
- +
current input
4-20 mA
Logic controller
0
/# /5
"8

!
!
)
(;&',

// /&
ACTIVE
current
voltage

" 8
+
voltage input
0-10 V
-
Logic controller

User manual - FLOW METER SPP-638
4.4. MAINTENANCE
The unit does not have any internal replaceable or adjustable components available to
the user. Pay attention to the ambient temperature in the room where the unit is operating.
Excessively high temperatures cause faster ageing of the internal components and shorten the
fault-free time of unit operation.
In cases where the unit gets dirty do not clean with solvents. For cleaning use warm water with
small amount of detergent or in the case of more significant contamination ethyl or isopropyl
alcohol.
Using any other agents can cause permanent damage to the housing.
Product marked with this symbol should not be placed in municipal waste. Please
check local regulations for disposal and electronic products.
16
!

User manual - FLOW METER SPP-638
5. FRONT PANEL DESCRIPTION
Symbols and functions of push buttons:
ymbol used in the manual:@3 )?A370B
Functions:
• Enter to main menu ( press and hold by at least 2 sec.)
• Exit the current level and Enter to previous menu (or measure mode)
• Cancel the changes made in parameter being edited
or ymbol used in the manual:@373*Bor@!,0 3B
Functions <
• tart to edit the parameter
• Enter to the sub-menu,
• Confirmation of changes made in parameter being edited
• While batcher mode: pause/start batching.
ymbol used in the manual:@CB@B
Functions <
• Change of the present menu,
• Modification of the parameter value,
• witching of the display between relay thresholds and number of batches
counter
or ymbol used in the manual: @SBor@*3 3B
Functions <
• witching of the display between total and instantaneous measurements
or batcher counter (while batcher mode only)
• Zeroing the currently displayed counter (press and hold by at least 2
sec.), the zeroing must be confirmed by @373*B button.
17
*3 3
.*$ *(*/ *&

A370
3 ) 373*
infrar d
r c iv r
display
programming
pushbuttons
Thr sholds xc ding
LED indicators (R)alarm LED indicator (F)

A370
3 )
373*
S
.=

!,0 3
373*

*3 3
D

User manual - FLOW METER SPP-638
6. PRINCIPLE OF OPERATION
After turning the power supply on, device ID and software version are showed on the
display, next the controller goes to the measurement mode.
6.1. MEASUREMENT MODE
In the measure mode, device displays instantaneous measurement (flow value or time
per one unit of flow, depending on „.!” parameter value) equivalent to input current, total
flow or batcher counter value.
Displayed value presentation is defined by parameters E.F, EF and EF
with resolution defined by parameters E.!3F, E!3F and E!3F.
... 879 876 543 . 219
“F unit” “F PrEc”
... 876 543 . 219
“F unit” “F PrEc”
Instantaneous flow (flow rate) is displayed in units defined by parameter E.F and
E.F (min., sec. or h), with resolution defined by E!F (max. 3 digits after decimal
point). Device converts measured current to selected units accordingly to conversion
characteristic selected by user. The measurement range equal to the nominal range is called:
nominal measurement range, and the measurement range equal to the extended nominal
range is called: permissible measurement range (Figure 6.1, 6.2).
Figur 6.1. D finitions of m asur m nt rang s in mod 4 ÷ 20 mA
If the result of measurement exceeds the permissible measurement range, warning F"G"F or
F"="F is displayed rather than input signal,depends on exceeded value (see description of
E=F or EGFparameters, paragraph ”FLouu” menu).
18
”=” parameter ”G” parameter
4 mA 20 mA
permissible measurement range
nominal measurement range

User manual - FLOW METER SPP-638
Figur 6.2. D finitions of m asur m nt rang s in mod 0 ÷ 20 mA
–If input current range is strongly overloaded, device can display improper results
–While time per one unit of flow is displayed (parameter E.!F = “!3”):
• If flow value equals 0, then message E" +!"F is displayed.
• If value of period is too high to be fitted on 6 digits, message E"+="F
(Overload) is displayed instead of the result.
• If flow value is different than 0 but value of period is too small to be fitted
on 6 digits, message E"0="F (Underload) is displayed instead of the
result.
Total flow is displayed in units defined by parameter EF with resolution defined by
parameter E!3F (max 3 digits after decimal point). If total flow counter overflows, warning
EF is displayed alternatively with maximum counter value. Total flow counter can be
zeroed using E)F option of E,=F submenu, using @S B button (press and hold by at
least 2 sec.), electrically via programmabl input or via R -485 interface by writing of value
0000h to any of total flow counter result registers.
Zeroing by @S B button can be activated using „)=” option of E,=F submenu.
Zeroing via programmabl input can be activated using „.” option of E!!F
submenu.
Parameter E)..F, allows to define input current value, below which total amount of
flow (incremented).
E)..F
                    +,=
)+073* 7+7)*3A373
E)FE)F<
T =" utoFF" ×20mA
100 for 0÷20 mA input
T =" utoFF" ×16mA
100 4mA for 4÷20 mA input
19
”G” parameter
0 mA 20 mA
permissible measurement range
nominal measurement range
i
i
i

User manual - FLOW METER SPP-638
Batching counter value is displayed in units defined by parameter EF with resolution
defined by parameter E!3F (max 3 digits after decimal point). If batcher counter overflows,
warning E,F is displayed alternatively with maximum counter value. Batching counter can
be zeroed using E)=,Foption of E,)GF submenu, using @SB button (press and hold by
at least 2 sec.), electrically via programmabl input or via R -485 interface by writing of value
0000h to any of batcher counter result registers.
Zeroing by @SB button can be activated using „)=” option of E,)GF submenu.
Zeroing via programmabl input can be activated using „.” option of E!!F
submenu.

@S B. Kind of displayed value is signalised by ESF LED. It lights,
while total flow is displayed. If batcher counter is displayed then ESF LED is pulsing.
Batching counter can be displayed while batcher mode only (set „ )3”=”,” in
H3=,/Fsubmenu).
Functions of @CB and @B buttons depend on kind of presently displayed value:
• If instantaneous flow (flow rate) is displayed ( LED marked ESF is off) or batcher counter
value (ESF LED is pulsing), user can check main threshold values and numb r of batch s
count r (which indicates how many times batcher was started). After pressing @CB or @B
buttons, name of the threshold (e.g. F3=!/F) and its value or F,)F label and
numb r of batch s count r will be displayed on the display in alternating mode.
If @CB or @B will be pressed in 5 sec again, the next threshold will be displayed, else the
device comes back to the measurement mode. If a free access is enabled (see description
of ”SECu” menu), user can change the value of particular threshold pressing button
@373*B (see: PARAMETERS EDITION). Using @S B button while numb r of batch s
count r is displayed and confirm H)=3,IF message by @373*B button causes zeroing
numb r of batch s count r.
• If particular parameter has been changed and confirmed in quick view mode, its
new value is displayed in alternating mode with parameter name by few
seconds. Confirmed changes may be checked or user can switch viewed
parameter pressing @CBor @B button.
•Numb r of batch s counter is incremented after each start of batching process
(every first start after batcher counter zeroing).
• If batcher counter value is displayed (ESF LED is pulsing) and counter value
exceeds 6 digits, then decimal point of the most left digit is pulsing. To view
most significant digits, it is required to decrease resolution or/and change unit to
m3.
• If total flow counter value is displayed ( LED marked ESF is on), and its length exceeds 6
digits, buttons @CB and @B enable switching between more and less significant digits.
Positions of currently displayed digits are signalized by flashing decimal points (see
example below).
20
i
i
i