Siruba AA-6 User manual

{iffl ~~~~
INSTRUCTION BOOK
C€
AA-6
~ ® -~Jii1S3~Jl~flE]
~ KAULIN MFG.CO .• LTD.
From the library of: Superior Sewing Machine & Supply LLC

EC DECLARATION OF CONFORMITY
According to the following EC Directive
Machinery Directive : 98 I 37 I
EC , as amended by 8913361 EEC and 731231 EEC.
The undersigned, DAVID LIN , representing KAULIN MFG. CO.. LTD. 11 F 128 Sec.
3 Min Shen E. Road, Taipei , Taiwan ROC., manufacturer, declares that the
machine described hereafter:
Portable Bag Closer
Model :AA-2/AA-6
Provided that it is used and maintained in accordance with the generally accepted
codes of good practice and the recommendations of the instructions manual, meets the
essential safety and health requirements of the Machinery Directive.
For the most
specific risks of the machine, safety and compliance with the essential
requirements of the Directive has been based on elements of : the European Standard
EN 292 - 1 & - 2 : 1992 Safety of machinery ; basic concepts, general principles for
design.
The
compliance of the model with the requirements of EC Machinery Directive was
established by AIB-VINCOTTE Inter n.f.p, Avenue A. Drouart 27-29 , B 1160 , Brussels,
Belgium ( Notified
body under the number 26 for machinery listed in annex IV of EC
Machinery Directive).
Date: JUL. I 15I 2005
Signature : ?J~ L:_, YJ
Qualification: VICE CHAIRMAN
From the library of: Superior Sewing Machine & Supply LLC

General Safety Instructions
Warning ! When using this machine, basic safety precautions should always be followed to reduce the
risk of fire, electric shockand personal injury, including the following.
Read all these instructions before operating this product and save these instructions.
!.Keep work area clean.
Cluttered areas and benches invite injuries.
2.Considerwork area environment.
Do not expose powerto rain. Do not use machine tools in damp or wet locations. Keep workarea well lit.
Dot not use powertools where there is risk to cause fire or explosion.
3.Guard against electric shock.
Avoid body contactwith earthed or grounded surfaces (e.g. pipes, radiators, ranges refrigerators).
4.Keep children away.
Do not let visitors touch the tool or extension code.
5.Dress properly.
Do notwear loose clothing or jewelry, they can be caught in moving parts. Wear protecting hair covering to
contain long hair.
6.Do not abuse the cord.
Never carry the machine by cord or yank it to disconnect it from the socket. Keep the cord away from heat,
oil and sharp edges.
7.Maintain machinewith care.
Follow instructions for lubrication and changing accessories. Inspecttool cord periodically and if
damaged have it repaired by
an authorized serviced facility.
B. Disconnect machine
When not in use, before servicing and when changing accessories.
9.Avoid unintentional starting.
Do not carry a plugged in tool with a finger on the switch. Ensure switch is offwhen plugging in.
1O.Check damaged parts.
Before further use of the tool, a guard or other part that is damaged should be carefully checked to
determine that it will operate properly and perform its intended function.
11. Warning.
The use of any accessory or attachment, other than those recommended in this instruction manual, may
present a risk of personal injury.
12. Have your tool repaired by a qualified person.
Repairs should only be carried out by qualified persons using original spare parts.
Special Warning For Electric Connection !
1.Incorporate this machine only with "CE" certificate hold to run control device.
2.Followthe instruction manual deviceto install control device.
3.Aiways earth machine appropriatelyduring operation.
4.Before adjustment, parts change or servicing must be sure to pull outthe plug from socket to prevent
the hazard of unintentionally start of machine.
From the library of: Superior Sewing Machine & Supply LLC

i!*i
at;Z~~
attf;Z~
at~
~at;Z~~
~ttz~~
i!& IIH~~ Itt
·llf*l
·mtt
·l'ftt
·:f'~UitS
·ttlm1'-
INDEX
SPECIFICATIONS
FEATURES
MAINTENANCE
NOTIC
THREADING
INSTALLATION OF NEEDLE
ADJUSTMENT OF NEEDLE BAR
STITCH LENGTH
INSTALLING AND/ OR REPLACING THE LOOPER
ADJUSTING THE LOOPER
TROUBLE SHOOTING
·THREAD-BREAKING
• STITCH-SKIPPING
• NEEDLE-BREAKING
• FAILURE
IN SEWING
• STITCHING BEING UNEVEN
MODEL AA-3/AA-6
Net
Weight (Kgs) 5 Noise Level, dB(A)
Serial No. Vibration(m/sec2)
Dimension Length Width
32cm
22cm
Ji/PAGE
1
1
1
2
2
3
3
4
4
5
5
75.5dB(A)
Height
30cm
From the library of: Superior Sewing Machine & Supply LLC

tt: 05
,~jl: 1/8HP, 90W.
ttBE: 7.2mm
m•:5kgs
1.-M~SM o
2.fi{1=fm~
~~~~-~m~aaM~~-~*~~
~Mtra<Ja D 'fttJH~itl&H.HPiiJ~~M.M
:ffl fl mlb tJJ 11r M BJi o
3.PJT~$~{~iH~J~iijJif!~~' ~·
:iE,~MUllltKfiJ.:Zi!io
4.iiJmM~ii~*!Ut, PP/EEIIIUt.tft.a•
~0
5.iiJ mM!lii)E~M~tcffiHifiiMlt~mM~
.:Z!Jff'!o
••
ltiJSiif;Wi(A909)~1.ffijl9HA900)\ii*!'m$~51&1JD
~~m~•~~·~~~~••,m•••
f1HII4' ~ 1JD ~ ~ 5111 o
-1-
SPECIFICATIONS
Needle: 05
Motor : 1/8HP, 90W.
Stitch length: 7.2 mm
Weight: approx.5 kgs
FEATURES
1. Single-thread chain stitching
2. Easy operation :
when the operator holdswith one hand the
opening ofthe bag to be sewn and carries
the bag closer with anotherhand, then
presses the powerbutton and starts
sewing.
When the sewing is finished, the thread
will be automaticallycut off.
3. Since all component parts have been
carefully designed and produced, quality
is verystableand reliable .
Due to this reason, the user(s) can be kept
away from the trouble ofrepairs .
4. It can be applied to sewmulti-layer PP/PE
bags, and/orcotton, linen bags.
5. It can be mounted to acertain fixture for
operating ,or be hung togetherwith a
suspending spring from the ceiling for
saving labor.
MAINTENANCE
Checkthe motor belt (A909) and motor
(A900) periodically.
Keepthe machine clean afterusing and
rememberto oil the machine, so that it can
provideyou with a quality sewing. If the bag
is carrying corn powder, orsimilar stuff, the
lubricating oil can notbe addedtoo much to
the machine.
From the library of: Superior Sewing Machine & Supply LLC

~~~~~~~e~~oo~~~a,~••
aq , Bl1l.~Ja~m,~~~~Ji!l o
NOTICE
The operator is requested to stop pressing
the powerbutton(A806) when the sewing on
one bag isfinished. Otherwise the life
of
motorwill decrease and I or possibly burn
out.
THREADING
--------------------------------------------------------------------------------------------1
~-~-ELiEit~.AMM~ ' ~~II1PJT~~
-0
i.lzlb&l~(A909) ' Stttf(ASOO)fii'iiiHi~ftJ:
YiM ' Blm!JII~(A501) ' *""FIItt ' MHttfi~
tt1i.Att¥-JlLJIIO ' lt!ild~(A501)' tJJ ~2
tt z!~j•~~rfft.tcil ' ~c 1112, 3 o
1112 /Fig. 2
-2-
For a correctthreading, see FIG .1 and do
accordingly.
111/Fig. 1
INSTALLATION OF NEEDLE
Pull the motor belt (A909), to make sure the
needle bar (ASOO) lifts to its highest position.
Loosen the screw (A501) ofthe needle holder,
take off the old needlefrom the needle holder,
and then insert the newneedle to the hole of
the needle holder. Fasten the screw. During
installing, remember to keep the needle1s
long groove facing the left side ofthe
machine. Please see Fig. 2&3.
tighten
1113/ Fig. 3
From the library of: Superior Sewing Machine & Supply LLC

1.~~~titf~~A1 01 R , Qlb~'li(A909) , 1i@
1ytt3~~114PJT5F
0
2.ll!fi!Bimtt•z!liM(SA26) o
3.~~tf'aqj!j}}l I ~ ll5Pfi5F ' ttN1ytt
(A3oo)tt~n~ I 1ytiz~~4'm~ttil*l
0.4mm 1 ifflilJit~1iltiZ~ilffii"'Ftfjjl!UT~
~tiZ*ilLJ:.*I o
••tt•xf-I:Z!ki**(SA26) ' :jij&J:.tt•il
~(A101R)' ~Wi~!iti~1ytf'(A300)~~
z rdi!Jt~ 1116 o
~
\\
114/Fig. 4
1115/Fig. 5
lE m ZtiBe lt 7. 2m m ' iffl ~*'llil(A203)i!i IIi
~1:62.7mm
1
1ri~tiBe4'~~ ' ftljtft~~
"'f:
1.~flA ii~'iil~IUI ' !fb~JUlWi o
2.~flA 'iil~lfa"'F ' .J..jJ&~~A81±itit&
;Zj!jJ!i=f'~2.7mm' ftiJi/lil~~flJii.Jm;Z
!liM(SA22)fi~'iil o
-3-
ADJUSTMENT OF NEEDLE BAR
1.Releasethe needle barcover (A 101 R), pull
the motorbelt (A909) to let the looper move
as per the instruction ofFig. 4.
2.Siightly loosenthe needle bar screw
(SA26).
3.Adjusting the heightof needle, please see
Fig.
5. When the needle and looper (A300)
meet together, the distance between the tip
of looperand the needle can not exceed
over 0.4mm. At the same time, the bottom
edge ofthe looper's tip just passes overthe
needle hole.
Fasten the needle bar screw (SA26), put
the needle bar protective cover
(A 101 R)
back, and then readjust the clearance
between the needle and looper according
to Fig. 6.
O J=r
116/Fig. 6
STITCH LENGTH
The normal stitch length is 7.2mm, and the
tips ofthe feed
dog (A203) should be set
higherthan the needle plate(A21
0} by 2. 7mm.
Ifthe stitch length is too long, checkand do
as follows:
1.Thetips of feed dog may be worn out,
then feed dog must be replaced.
2.The feed dog may possiblysink, and the
height of the tips of feed dog over the
needle plate is less than 2.7mm
consequently. Loosen the feed dog holder
screw (SA22) and adjustthe feed dog.
From the library of: Superior Sewing Machine & Supply LLC

1.QibBZ1ii(A909){f~fl~1±iiil"l!i o
2 .• ~~tt6UI~(SA19) I IDl"'F~tt.Jm
(A301 R) o
3.ft~~tt!R**(SA03) I Im"'F~tt(A300)
0
4.~tiT~tt I MI.A.~tt~Pi
0
5.tf!~ttJ~iUl.A.~tt~llbJ:.(A303R) I ~~~
tt ~~ 1116 I :ttltiUII'*(SA03)
0
6.~~~tt~(A301R)~II4 I M!I\!Ril~
(SA19) o
1.:S.R~£~~tt~1"~li'H~~ I @1'±:~~
''~tt*b" (A303R) , ~-~fa(A301 R)~
~!MM14M~~f1:~~ o
2.~tt1±1ru~;Ltl~ I ~ttttjjlij~tt••~
~~~1.2mm 1 ~114 o
3.:S~~jjj~a~ , ltst,llhBZt.Wi(A909) I {f~
tt3~1!!J~;L~I!ii~~-~~#-~;L
!II**(SA03).!lD~~;L o
-4-
INSTALLING AND/ OR
REPLACING THE LOOPER
1.Turn the motorbelt (A909) to make sure the
feed
dog is at its highest position.
2.Loosen the looper holder screw
(SA 19) and
take offthe Iooper holder
(A301 R).
3.Loosen the screw (SA03) oflooper, and
take offthe looper(A300).
4.Replace the old looper, and put the new
looperto the holder.
5.Put the holder backto the holder bed
{A303R) and adjustthe height and timing of
looper as per Fig. 6and fasten the screw
{SA03).
6.Adjustthe position of looper holder
{A301 R) as per Fig. 4and fasten the screw
(SA19).
ADJUSTING THE LOOPER
1.1f the replacement oflooper is required, the
adjustment
is then not necessary. But when
the looper holder
bar, plastic cam or cam
component parts are replaced, the
adjustmentwould be a must.
2.When the looper returns backwardsto its
extreme, looper's tips will be only away
from the needle's edgeabout a distance
1.2mmsee Fig.
4.
3.1f aadjustment is required, first move the
motor beltA909, to letthe looper come
backto its extreme position. Loosen the
screw (SA03)
on looper holder bed, and
then adjust it.
From the library of: Superior Sewing Machine & Supply LLC

••
1 .• * f!l ~ it ~ ~ IJJ.p.J< it ~ I ~ $t ~ • J:
51B I j..jj~ f11 51 IJ1j If.
0
2.ff~tttiiilalt~1"1Efil I ~ttttmi~~-
]IC~!tifi:jijiifi~~O
3.1"1Efil*-'*leJZ~)J I ~~~~~~**-'• 0
~ttt
1.M*W~it~BJt1Jtj]j(l£~ I ~5'CH~IciJ:51B
j..). !I jiiJ ]I 0
2.~ tt'fiLii j!j~~1" lE fil I ~*~ tt'fiLii.~ ~~~
5'6o
3.tiB9llilltitll1" JE fil I tll:6:tillill~ 1112 O
4.j§*li!li1lJtm~tii I ~~;tifT O
•tt
1.tt~~1"JE fil I ~*tt!Y-J~jJJ:!: 1~H±mw
(f(j~jl~~~~o
2.~tt~&:!:e1"JEfil I ~~~4~1l o
~•n~a
10 tt '-& If liB 1" :If I Jf :If Bjt il ifi 0
2.jlf!Ji 1lJft~IUii1"lf Iitifi 0
ttBe~-
1.jlfiJil!li!1J1"S I i~J~ii'MZIBJJ
0
2.~f~AIUii I !tifT 0
-5-
TROUBLE SHOOTING
THREAD-BREAKING
1.Before sewing the pitch-coated bags or
water-proof paper bags oil the thread first
to increase the lubrication, so that thread
breaking can be avoided.
2.1f the looper is damaged or incorrectly
adjusted, looper's tip needs to be polished
or replaced, and then adjust onceagain.
3.The thread breaking may be caused by
incorrect threading or wrong thread
tension. Check the threading as per Fig. 1.
STITCH-SKIPPING
1.When sewing the pitch-coated bags or
water-proof paper bags, the stitch-skipping
easily happens. We suggest oiling the
thread before sewing.
2.The position of loopermay be wrong. Check
the looperas per Fig. 5&6.
3.The position
of needle is wrong, Check the
needle as per Fig. 2.
4.Threading tension spring may be damaged.
Replace the damaged one.
NEEDLE-BREAKING
1.1ncorrect needle installation. Check if the
needle's long groove is facing the left side
of the machine.
2.1ncorrect needle installation. Check and
adjustas per Fig.
4.
FAILURE IN SEWING
1.The needle plate may be deformed.
Replace it.
2.The presser foot may be damaged. Replace
it.
STITCHING BEING UNEVEN
1.The pressure
of the presser foot may be
improper. Adjust the pressure.
2.The feed dog is damaged. Replace it.
From the library of: Superior Sewing Machine & Supply LLC

1Ji~.Jil1Q.II!f}~ KAUUN MFG.CO.,LTD.
The specification and/or appearances of the equipment described In this Instruction book are subject to
change because of modification without previous notice .
A941 D-1. JUN. 2005
From the library of: Superior Sewing Machine & Supply LLC