sisel ENDA ATF02 User manual

ENDA
ATF02
ON TIME
OFF TIME
OFF RANGE
.4
.6 .8
0
1
.2
10M
10H
H
10S
M
S
.4
.6 .8
0
1
.2
ON RANGE
10M
10H
H
10S
M
S
ENDA ATF02 Rail Mounted Flasher Analog Timer
* Can be triggered with supply voltage.
* Triggering output (OUT1 optional).
* Contact output for timing function (OUT2).
* ON and OFF time durations can be adjusted separately.
* 6 Different timing units (S, 10S, M, 10M, H, 10H)
* Rail mounted.
* Screw-terminal connection.
* CE marked according to European Norms.
ATF02 - xR - xV
Power Led
ton toff ton toff
Power
Power
OUT2 NO
OUT2 Led
90-250V AC
24V AC/DC
Supply Voltage
UV
LV
1 Relay
2 Relays
Output Relay(s)
1R
2R
ORDER CODE ATF02 - xR - xV
Product Basic Code
Rail Mounted
Analog Timer
OUT1 NO
ton=ON RANGE x ON TIME
toff=OFF RANGE x OFF TIME
1/2 ATF02-E-01-201412
0 ... +50°C/-25 ... +70°C (With no condensation and icing).
OUTPUT CONTROL
SİSEL MÜHENDİSLİK ELEKTRONİK SAN. VE TİC. A.Ş.
Şerifali Mah. Y.Dudullu 34775
ÜMRANİYE/İSTANBUL-TURKEY
Tel : [phone] Pbx. Fax : [phone]
url : www.enda.com.tr
Barbaros Cad. No:18
Thank you for choosing ENDA ATF02 Rail mounted flasher analog timer.
Technical Specifications
Read this document carefully before using this device. The guarantee will be expired by device demages if you don't
attend to the directions in user manual. Also we don't accept any compensations for personal injury, material
damage or capital disadvantages.
Max. humidity 80% for temperatures up to 31°C decreasing linearly to 50% relative humidity at 40°C.
ENVIRONMENTAL CONDITIONS
Max. 2000m
IP20, According to EN 60529
Do not use the device in locations subject to corrosive and flammable gasses.
Height
Ambient/storage temperature
Max. relative humidity
Rated pollution degree
ELECTRICAL CHARACTERISTICS
Scale
EMC
İnsulation test voltage
Supply voltage
Power consumption
Connection
Reset time
Accuracy
Safety requirements
90-250V AC +%10 -%20, 50/60Hz or 24V AC %10, 50/60Hz or± ± 24V DC %10
Max. 10VA
Screw-terminal connection.
Depending on the effect of voltage: max %0.2
EN 61326-1: 2012
EN 61010-1: 2010 (pollution degree 2, overvoltage category II)
3kV AC min. 1 minute, 4,2kV DC min. 1 minute.
Can be adjusted between 0 and 1.
Max. 0.04 seconds.
Depending on the set value settings:max %4.5
Depending on the effect of temperature :max %1
OUTPUTS
Control outputs (OUT1/OUT2)
Control output state
Life expectancy for relays
Relay: 250V AC, 10A (for resistive load), NO+NC
Without load 10.000.000 operation; 250V AC, 10A resistive load 50.000 operation.
OUT2 LED lights up for length of ON and blinks for length OFF.
CONTROL
Timing function
Timing unit
ON : ON time duration for relay. OFF : OFF time duration for relay. Can be adjusted on device.
ON and OFF time durations can be selected as, second, 10 seconds, minute, 10 minutes, hours and 10 hours on device.
HOUSING
Mounting
Dimensions
Weight
Enclosure material
Rail mounted (EN 60715, Th35)
W18xH90xD66mm
Approx. 90g (after packaging)
Self extinguishing plastics.
While cleaning the device,solvents (thinner,benzine,acid etc.) or corrosive materials must not be used.
tt
t t
t t

.4
.6 .8
0
1
.2
10S
M
10M H
S
10H
NC NC
C C
NO NO
U1 U1
U2 U2
NC NC C C NO NO
ENDA
ON TIME
OFF RANGE
.4
.6 .8
0
1
.2
10S
M
10M H
S
10H
18,5 mm
1
2
1
ENDA
ATF02
OFF TIME
OFFRANGE
.4
.6 .8
0
1
.2
10S
M
10M H
S
10H
OFF TIME
OFF RANGE
ON RANGE
10S
M
10M H
S
10H
ATF02
.4
.6 .8
0
1
.2
OFF TIME
ENDA
ON TIME
OFF RANGE
.4
.6 .8
0
1
.2
10S
M
10M H
S
10H
ON RANGE
10S
M
10M H
S
10H
ATF02
.4
.6 .8
0
1
.2
OFF TIME
ONRANGE
.4
.6 .8
0
1
.2
ON TIME
10S
M
10M H
S
10H
.4
.6 .8
0
1
.2
Relay status LED
(OUT1 LED lights up when OUT1 relay is turned on).
90-250V AC or
24V AC/DC
Cable size : 1,5mm²
Fuse
F 100 mA
250V AC
62 mm
66 mm
8 680407 715008
ENDA
ATF02-2R-UV
ANALOG FLASHER TIMER
SN: XXXXXXXXX
Made in Turkey
OUT1 / OUT2 :
250V AC 10A
RESISTIVE LOAD
POWER :
90-250V AC
50/60Hz
OUT1
NC NO
C
U1 U2
OUT2
NC NO
C
90 mm 69 mm 45 mm
ENDA
ATF02-2R-UV
ANALOG FLASHER TIMER
SN: XXXXXXXXX
Made in Turkey
OUT1 / OUT2 :
250V AC 10A
RESISTIVE LOAD
POWER :
90-250V AC
50/60Hz
OUT1
NC NO
C
U1 U2
OUT2
NC NO
C
OUT2
OUT1
CONNECTION DIAGRAM
ENDA ATF02 Series timers are rail mounted devices. Make
sure that the device is used only for intended purpose. The
shielding must be grounded on the instrument side. During an
installation, all of the cables that are connected to the device
must be free of energy. The device must be protected against
inadmissible humidity, vibrations, severe soiling and make sure that the
operation temperature is not exceeded. All input and output lines that are not
connected to the supply network must be laid out as shielded and twisted cables.
These cables should not be close to the power cables or components. The
installation and electrical connections must be carried on by a qualified staff and
must be according to the relevant locally applicable regulations.
Supply indicator.
1) Mains supply cords shall meet the requirements of IEC
60227 or IEC 60245.
2) In accordance with the safety regulations, the power supply
switch shall bring the identification of the relevant instrument
and it should be easily accessible by the operator.
Phase
Neutral
Fuse should
be connected.
Switch
Holding screw
0.4-0.5Nm.
DIMENSIONS MONTAGE
For mounting the device to the panel :
Push the device in direction 1 , the rails
provide the key to keeping the rail.
For removing the device from rail;
Push the rail lock in direction 1 with a
screwdriver and pull the device in
direction 2 .
ON Time unit selection.
ON Timing selection.
t
t
OFF Time unit selection.
t
OFF Timing selection.
t
2/2 ATF02-E-01-201412
SİSEL MÜHENDİSLİK ELEKTRONİK SAN. VE TİC. A.Ş.
Şerifali Mah. Y.Dudullu 34775
ÜMRANİYE/İSTANBUL-TURKEY
Tel : [phone] Pbx. Fax : [phone]
url : www.enda.com.tr
Barbaros Cad. No:18