AMP Lighting EscherPro AAL-1023 Series Operating and safety instructions

- 1 -
INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP®EscherPro MR11 Spotlight (Lamp Ready)
AAL-1023 Series

Package Contents
Product Dimensions
A. (1) Fixture Body
B. (1) Stake
1”
2.83”
3.72”
- 2 - - 3 -
1.82”
4.25”
3”
AMP®EscherPro MR11 Spotlight
AAL-1023
Important Safety Instructions: Read Before Installation
INSTALLATION & MAINTENANCE GUIDE
!
www.amplighting.com
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
Important Safety Instructions
!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
[email protected] • 813.978.3900

Install Stake
1
Board
Ground
Soil
Stake
- 4 - - 5 -
Install Luminaire to Stake
2
Ground
Supply Wires
Wireway Slot
Soil
Stake
Luminaire
Determine the desired location for mounting
the luminaire. Hammer the stake into the
ground until ange of stake is ush to grade.
To avoid damage to the stake, place a board
on top of the stake while hammering.
NOTE: If the ground is hard and the stake
is difcult to install, make a crosscut in the
ground using a at shovel.
Clear away an area in the ground
at the wireway slot on top of the
stake. Lay the luminaire pigtail
into the wireway slot and attach
the luminaire onto the stake.
Tighten until snug.
Wire Connections
3
Strip both leads from the luminaire pigtail. Using two wire connectors
(sold separately), connect the leads from the luminaire to the main
supply cable leads.
Pigtail
Main Low Voltage
Supply Cable
Wire Connectors
Remove Glare Guard
4
Loosen the set screw and remove
the glare guard from the xture
body.
REMOVE
Fixture Body
Set Screw
Glare Guard
Remove Lens
5
Rotate the lens to remove it
from the xture body.
REMOVE
ROTAT E
Fixture Body
Lens
AMP®EscherPro MR11 Spotlight
AAL-1023
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com [email protected] • 813.978.3900

- 7 -- 6 -
Install MR11 Bulb
6
Insert MR11 bulb with the correct
wattage and type marked on the
xture label.
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
MR11 Bulb
Socket
ROTAT E
Install Lens
4
Place the lens back onto the
xture body and rotate it until
it is secured properly.
Fixture Body
Lens
Install Glare Guard
5
Install the glare guard back
onto the xture body and
secure with previously
removed set screw.
Fixture Body
Set Screw
Glare Guard
Using the provided Allen wrench,
loosen the knuckle and adjust
the xture body to your desired
direction. Once your desired
direction is achieved, tighten the
knuckle into place.
ROTAT E
Adjust Bulb Direction
6
Fixture Body
Allen Wrench
Knuckle
Remove the glare guard and the lens to expose the MR11 bulb and replace it
with the correct wattage and type marked on the xture label. Then,
reinstall the lens and the glare guard.
IMPORTANT: MR11 bulb must be protected from moisture and dust at all
times. Always reinstall the lens and the glare guard when removed.
Install/Replace Bulb
AMP®EscherPro MR11 Spotlight
AAL-1023
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com [email protected] • 813.978.3900

- 8 -
IS-AAL-1023
Specications and product details subject to change without notice.
© Copyright 2019, AMP®Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com