Volt VPL-1042-4-BBZ User manual

VOLT®Low Voltage Landscape Lighting
Cypress Bollard
VPL-1042-4-BBZ
INSTALLATION INSTRUCTIONS
- 1 -
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700

VOLT®Cypress Bollard
VPL-1042-4-BBZ
Important: Please Read Before Installation
Important Safety Instructions
INSTALLATION INSTRUCTIONS
!
!
www.voltlighting.com
- 2 -
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
xture.
2. Warning: this xture is not intended to be installed within 10 feet [3
meters] of a pool, spa or fountain.
3. This xture is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm) in
order to connect to the main low voltage cable.
5. Wiring connections must be made with UL Listed wire connectors that
are suitable for the application.
6. Position the wire connector so that it is located within 6 inches (15.2 cm)
from a building structure, a luminaire, or tting.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or shield.

Package Contents
Product Dimensions
[email protected] • 813.978.3700
- 3 -
A. (1) Fixture Body
B. (1) Coupler
C. (1) Hat
D. (1) Finial
22.4”
5.9”
6.45”

INSTALLATION INSTRUCTIONS
www.voltlighting.com
Install Fixture Hat
1
- 4 -
Install Stake
2
VOLT®Cypress Bollard
VPL-1042-4-BBZ
Screw the coupler onto the top
center of the xture body and
hand tighten until snug.
Secure the xture hat onto the
coupler with the nial and hand
tighten until snug.
Finial
Fixture Hat
Fixture Body
Coupler
Determine the desired location
for mounting the stake mount.
Hammer the stake into the
ground until ange of stake
is ush to grade. To avoid
damage to the stake, place a
board on top of the stake while
hammering.
Note: If the ground is hard and
the stake is difcult to install,
make a crosscut in the ground
using a at shovel.
Board
Ground
Soil
Stake

[email protected] • 813.978.3700
- 5 -
Install Fixture Body to Stake
3
Pass the xture wire through
the center hole of the stake.
Thread the xture body onto
the stake and hand tighten until
snug.
Fixture Body
Fixture Wire
Ground
Soil
Stake

INSTALLATION INSTRUCTIONS
www.voltlighting.com
- 6 -
Wire Connections
4
VOLT®Cypress Bollard
VPL-1042-4-BBZ
Strip both leads from the xture body. Using two wire connectors (sold
separately) connect the leads from the xture body to the main supply
cable leads.
Pigtail
Main Supply Cable
Supply Wire from
Fixture Body
Wire Connectors

[email protected] • 813.978.3700
- 7 -

IS-VPL-1042-4-BBZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
www.voltlighting.com
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 8 -