AMP Lighting LocketPro Mini Hanging Light Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP® LocketPro Mini Hanging Light (Lamp-Ready)
ASI-9007-4036-B-BZ

AMP® LocketPro Mini Hanging Light (Lamp-Ready)
ASI-9007-4036-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
[email protected] • 813.978.3900
Product Dimensions
–3–
Important Safety Instructions: Read Before Installation
!
Important Safety Instructions
!
Package Contents
Parts Required (Sold Separately)
This xture is intended for installation in accordance with local codes and the
National Electric Code (NEC). Failure to adhere to these codes and instructions
may result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, opera-
tion maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or
more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply (trans-
former) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. The unit low voltage cable should:
a. Be protected by routing in close proximity to the luminaire or tting,
or next to a building structure such as a house or deck;
a. Not be buried except for a maximum 6 inches (15.2 cm) in order to
connect to the main low voltage cable; and
a. Have the length cut o so that it is connected to a connector within 6
inches (15.2 cm) from the building structure, a luminaire, or tting.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Turn o/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may dam-
age lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
A. (1) Fixture
B. (1) Fixture Chain
C. (1) Chain Link
D. (1) Mounting Bracket
E. (3) Self-tapping Screws
F. (3) Flat Washers
A. (1) Bi-Pin Brass Puck Light
2” 2”
3” 3”
7.32”

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
2
1
[email protected] • 813.978.3900
–5–
AMP® LocketPro Mini Hanging Light (Lamp-Ready)
ASI-9007-4036-B-BZ
Remove Shade
Install Bi-Pin Brass Puck Light
Fixture
Bottom Shade
Screw
Use a screwdriver to remove
the screws from under the
xture. Then take o the
bottom shade.
Fixture
Insert the Bi-Pin brass puck light
into the socket and secure with the
two screws provided. Tighten with a
screw driver.
CAUTION: This xture is for LED use
only. Do not exceed maximum watt-
age marked on luminaire label.
NOTE: DO NOT touch the Bi-Pin brass
puck light with bare hands. Use soft
cloth to handle the puck light.
Socket
Screw
Bi-Pin Puck Light
Bi-pin Puck Light
Holes on Bi-pin Puck Light
Holes on
Mounting
Plate
ROTATE
TIPS: If the holes on the Bi-Pin
puck light do not align to the
holes on the mounting plate
after installation, rotate the
Bi-Pin puck light slightly to
line the holes up and then
secure with screws.
3
Re-install Shade
Fixture
Bottom
Shade
Screw
Place the bottom back onto the x-
ture and secure with the previously
removed screws. Tighten with a
screw driver.
4
Install Mounting Bracket
Wall Anchor
(not included)
Flat Washer
Self-tapping Screw
Mounting
Bracket
Ceiling Attach the mounting bracket onto
the desired ceiling surface. Secure
with the at washers and self-tap-
ping screws.
Note: Wall anchors are required
for certain installation conditions
(concrete or brick walls). Mark on
the desired ceiling surface for wall
anchors by using the holes on the
mounting bracket. Remove the
mounting bracket and drill proper
holes on the desired ceiling surface
and then insert the wall anchors.

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
[email protected] • 813.978.3900
–7–
AMP® LocketPro Mini Hanging Light (Lamp-Ready)
ASI-9007-4036-B-BZ
5
Attach Fixture to Mounting Bracket
Supply Wires Fixture Chain
Fixture
Mounting
Bracket
Chain Link
Ceiling Loop
Adjust the xture chain to the desired
length by removing the links if needed.
(Note: Pliers are required for this step).
With the xture chain unattached to the x-
ture loop on top of the xture body; or the
ceiling loop on the underside of the mount-
ing bracket, pull the supply wires through
the xture chain alternating between the
links.
After the wires are through the xture
chain, pull the supply wires up and around
the backside of the mounting bracket.
Attach one end of the xture chain to the
xture loop at the top of the xture body.
Lift the xture body and xture chain up
and attach the other end of the xture chain
onto the ceiling loop on the bottom of the
mounting bracket with the chain link.
The xture will now hang safely. Close the
chain loop at the ceiling loop.
6
Adjust Fixture
Adjust the xture chain to the desired length by removing the links if
needed. (Note: Pliers are required for this step).
With the xture chain unattached to the ceiling loop remove the links
to create the length needed. Then, pull the supply wire from the xture
through the chain alternating between the links.
After the wire is through the chain, pull the additional wire through the
mounting bracket.
Attach the xture chain to the ceiling loop using the chain link.
7
Wire Connections
Fixture
Pigtail
Transformer
(Sold Separately)
Supply Wire
Strip both leads from the luminaire
pigtail. Connect the leads from the
luminaire supply cable to the trans-
former (sold separately).

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com