SKYDANCE DT User manual

● AC phase-cut mosfet DALI dimmer, one DALI address, one channel output.
● In accordance with DALI standard protocol IEC 62386-102, IEC 62386-207 and in compliance with DALI products
from other international incorporation.
● DALI address can be manually assigned and shown in digital display or automatically assigned by DALI master.
● Reverse-phase dimming or forward-phase dimming selectable.
● Connect with external push switch to achieve on/off and 0-100% dimming function.
● To dim and switch single color dimmable LED lamps, traditional incandescent and halogen lights.
User Manual Ver 1.0.2
Technical Parameters
Model No.: DT
Features
Page 1
Mechanical Structures and Installations
1DALI address/1 Channel output/Leading edge or trailing edge/Numeric display
AC Triac DALI Dimmer
AC L input
AC N input
LVD
Wiring Diagram
AC N Output
AC L Output
DT AC Triac DALI Dimmer
Output current Max 1.2A
Input voltage AC100-240V
Output voltage AC100-240V
Input and Output Safety and EMC
EMC standard (EMC)
EN 55015:2013
EN 61547:2009
EN 61000-3-2:2014
EN 61000-3-3:2013
Certification CE,EMC,LVD
EN 61347-2-11:2002
EN 61347-1:2015
EN 62493:2015
Safety standard(LVD)
Warranty
5 years
Warranty
Operation temperature
Case temperature (Max.)
Environment
IP20
IP rating
Ta: -30
O
C ~ +55
O
C
T c: +85
O
C
Output power 120-288W
Setting key Digital display
Two groups of DALI signal input
DALI bus no need distinguish
plus-minus polarity
187.00 mm
46.00 mm
22.00 mm
DALI
Master
N
L
AC 100-240V
tc: 7 0℃
0.5-2.0mm²
4-5mm
Wire Pre parati on
PUSH -DIM
SIGN AL INPUT
DA1
DA2
DA1
DA2
L
N
N
L1
AC100-240V OUTPUT
AC100-240V INPUT
DT DALI AC Triac Dimmer
Uout=100-240VAC
Iout=1.2A
Pout=120-288W
Temp Range:
-30℃~+55℃
Uin=100-240VAC
Iin=1.3A
0-6 0-9
Push switch com
Push switch in
Dimmable LED light
LED light
Dimmable
LED Driver
tc: 7 0℃
0.5-2.0mm²
4-5mm
Wire Pre parati on
PUSH -DIM
SIGN AL INPUT
DA1
DA2
DA1
DA2
L
N
N
L1
AC100-240V OUTPUT
AC100-240V INPUT
DT DALI AC Triac Dimmer
Uout=100-240VAC
Iout=1.2A
Pout=120-288W
Temp Range:
-30℃~+55℃
Uin=100-240VAC
Iin=1.3A
0-6 0-9
tc: 7 0℃
0.5-2.0mm²
4-5mm
Wire Pre parati on
PUSH -DIM
SIGN AL INPUT
DA1
DA2
DA1
DA2
L
N
N
L1
AC100-240V OUTPUT
AC100-240V INPUT
DT DALI AC Triac Dimmer
Uout=100-240VAC
Iout=1.2A
Pout=120-288W
Temp Range:
-30℃~+55℃
Uin=100-240VAC
Iin=1.3A
0-6 0-9
N
L
AC 100-240V
Note: When calculating the maximum number of load lamps or drivers, the input power or input current
parameters of a single lamp or driver must be used, the output power parameters can not be used,
otherwise, the product will be overloaded and damaged.
Please carefully ensure all wire connections and polarities are correct and secure before applying power,
otherwise this controller will be damaged.
Caution:

Push-Dim Function
● Short press:
Turn on or off light.
● Long press (1-6s):
Press and hold to step-less dimming,
With every other long press, the light level goes to the opposite direction.
● Dimming memory:
Light returns to the previous dimming level when switched off and on again, even at power failure.
● Synchronization:
If more than one controller are connected to the same push switch, do a long press for more than 10s,
then the system is synchronized and all lights in the group dim up to 100%.
This means there is no need for any additional synchrony wire in larger installations.
We recommend the number of controllers connected to a push switch does not exceed 25 pieces,
The maximum length of the wires from push to controller should be no more than 20 meters.
The provided Push-Dim interface allows for a simple dimming method using commercially available non-latching
(momentary) wall switchs.
User Manual Ver 1.0.2 Page 2
Operation
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Safety & Warnings
DALI address assigned by DALI masters
DALI address can also be assigned by DALI Master controller automatically.
Please refer to user manuals of compatible DALI Masters for specific operations.
The digital display will show “AU” When the DALI master is assigning address.
After address is assigned, the digital display will show the start DALI address”xx”, xx is from 00 to 63.
Set DALI Address via buttons
● Long press any of the two buttons for 2s, prepare for set the start DALI address, digital display start flashes.
● Short press first button to set “tens” position and second button to set “units” position.
● The address can be set from 00~63-FF. no DALI address is assigned for the dimmer, digital display shows “FF”.
● Long press any of the two buttons for 2s or timeout 10s, quit start DALI address setting, digital display stop flashes.
Reverse-phase or for ward-phase dimming setting
Long press two buttons at the same time for 2s, switch between reverse-phase dimming("CR") or forward-phase("CF") dimming.
DT AC Triac DALI Dimmer